B&B Electronics 9POP4 User manual

Documentation Number –p/n 9093R1 9POP4-0712qsg
©2010 B&B Electronics Manufacturing Company
C
Ce er rt ti if fi ic ca at ti io on ns s
•FCC Class B
•CE
oEN 55022: 2006 + A1:2007 Class A Emissions
oEN 61000-6-1: 2007 Generic Standards for
Residential, Commercial and Light-Industrial
Environments
oEN 61000-4-2: 2008 Electro-Static Discharge
(ESD)
oEN 61000-4-3: 2006 Radiated Field Immunity
(RFI)
oEN 61000-4-4: 2004 Electrical Fast Transients-
Burst (EFT)
oEN61000-4-5: Ed2, 2005 (Surge)
oEN 61000-4-6: 2005 Conducted Immunity
C
Ch he ec ck k f fo or r A Al ll l R Re eq qu ui ir re ed d H Ha ar rd dw wa ar re e
9POP4 RS-232 Optical Isolator
This Quick Start Guide
12VDC Wall Power Supply (sold separately).
Recommended Power Supplies:
oUS – 232PS
oUK – PS1UK-1000
oEU – PS1EU-1000
Put
Quick Start Guide
9POP4
Optically Isolated RS-232
Repeater
D
DB B9 9 P Pi in n- -o ou ut t
1. DTE stands for Data Terminal
Equipment: these include Computers,
PLC's, and most devices which are not
used to extend communications. Think
COMPUTER for DTE.
2. DCE stands for Data Communications
Equipment: these includes devices
intended to plug directly into a DTE
port, Modems and devices that extend
communications like a modem, such
as RS-422, RS-485, or Fiber Optic
converters or Radio Modems. Think
MODEM for DCE.
3. On the DCE (female) side, Pins 1, 4,
and 6 are tied together internally.
4. On the DTE (Male) side, Pins 4 and 6
are tied together internally.
2
1
I
In nf fo or rm ma at ti io on n – – C Co on nn ne ec ct to or rs s
Connectors
A
DB9 Female – Data Communications Equipment
(DCE)
A
DB9 Male – Data Terminal Equipment (DTE)
C
Power – 12 VDC Jack, 2.5 mm Center Positive
Pin
Signal
DCE
DTE
1
DCD
Output
Input
2
RD
Output
Input
3
TD
Input
Output
4
DTR
Input
Output
5
GND
---
---
6
DSR
Output
Input
7
RTS
Input
Output
8
CTS
Output
Input
9
RI
Output
Input
3
4

Documentation Number –p/n 9093R1 9POP4-0712qsg
©2010 B&B Electronics Manufacturing Company
5
W
Wi ir ri in ng g E Ex xa am mp pl le e
P
Po ow we er r
1. The two sides of the isolator are
powered from a single +12VDC power
supply and maintain isolation. This
powering configuration allows the
device to be run in any system with
only a single supply, regardless of the
power levels on the RS-232 ports.
2. In order to maintain the required
isolation, use the recommended
power supply. Using an unregulated
power supply may negate the
isolation.
3. Recommended Power Supplies:
a. US – 232PS
b. UK – PS1UK-1000
c. EU – PS1EU-1000
L
Lo oo op pb ba ac ck k T Te es st t
Use a DB9 Female to DB9 Male cable to connect a
PC to the DCE port.
(Recommended) Connect a DB9 Female to DB9
Female cable to the DTE port.
On the DTE Port, jumper pin 2 to 3 and pin 7 to 8 on
the female end of the cable. This loops TD to RD and
CTS to RTS.
Using hyper terminal or similar program, connect to
the appropriate COM port (remember to set the baud
rate to 9600).Turn off hyper terminal local echo
Transmit data. The same data should be returned.
6
7