Bang & Olufsen BeoVision 4-85 User manual

BeoVision 4-85
Installationguide for BeoVision 4-85, Floor Stand
Version 1.1

Introduction 2
Introduction
The aim for this guide is to assist the installer to attain a smooth and correct installation. The guide is intended as a guideline and may in certain
cases not be 100% relevant. However, the guide could be useful as a reference book to nd informations and dimensions about the products.
Content
The main content of the Installationguide describes the following:
- Precautions
- Assembly and installation of Floor Stand
- Mechanical specications for BeoVision 4-85, Floor Stand.
Important
! Since both the plasma panel and the stand are sizeable dimensions, it is strongly recommended to read the warning and precautions section
carefully. Otherwise there is major risk of damaging personnel or furnitures.
How to navigate this guide
When the guide is opened, it automatically opens in Full Screen Mode (can be left as desired - see below). This is primarily done to optimize the
usability of screen reading. There are several ways to navigate when using the guide, see the survey of keys, shortcuts and hotkeys below:
/ (arrow keys on the keyboard) navigates to the next page
/ (arrow keys on the keyboard) navigates to the previous page
Esc (Esc button ) exit Full Screen Mode (press CTRL + L to return to Full Screen Mode).
Another feature to optimize the navigation is the navigation icons in the bottom of the screen (see below for explanation).
Navigates you to the previous view
Navigates you directly to the start page
Navigates directly to the table of contents (theese are active links - click the link to be directed directly to the chapter)
Prints the document - the print dialog box opens (Ctrl + P also brings up this feature)
Furthermore to ease the navigation, this guide contains links. The links are mouseover active and marked with blue text. Just click on a page
reference to be transferred to that page.

Warning / Precautions 3
Warning
Before the installation is started it is strongly recommended to ensure the following:
! Ensure that the oor construction is strong enough to support long-term use. If its strenght becomes insufcient over the course of long-term use,
the product may tip over, and possible causing injury.
! Installation and removal should be carried out by qualied installers only. If the Floor Stand is installed incorrectly, the display may fall down, and
possible causing injury.
! Do not install in places which are subject to high humidity, dust, oil fumes, water vapour or excessive heat. These can have adverse effects on the
plasma display operation, and re or electric shocks may occur.
! Exercise caution when selecting the location for the display. It may discolor or deform due to light or heat if it is placed where it is exposed to direct
sunlight, or near a heater.
!Only moving company are allowed to lift or move the TV and Floor Stand.
Not technicians or installers.
Precautions
Before the installation is started it is strongly recommended to read this section carefully. The description is only intended as a guiding instruction
which may vary compared to the actual situation.
Edges of the items
The shape of BeoVision 4-85 and the oor stand may be considered as potential risks when they are free hanging items. Be aware of their
positions when they are free hanging in the active working area during the installation, to avoid getting injured.

Installation overview 4
Installation overview
Apart from the Floor Stand, the basic set-up of BeoVision 4-85 includes the
following items:
- BeoVision 4-85 PDP (Plasma Display Panel) incl. IR, ACM and shielding frames
- BeoSystem 3
- BeoLab 10
The Floor Stand installation includes:
- Floor Stand with motorised speaker bracket (incl. accessorie bags with e.g., EMC
caps, washers, screws etc.).
- Cabinet parts (TV cabinet, speaker cabinet and stand cabinet).
- Decorative plates.
- BeoLab 10 wall bracket (attached to the speaker bracket).
Floor Stand installation
Introduction
Warning/Precautions
Installation overview
Installation, Floor Stand
Installation, TV
Installing the TV on the
Floor Stand
Installing shielding
frames
Connection of cables to
the TV
Horizontal TV adjust
Assembly of cabinet parts
Connection of
BeoVision 4-85 /
BeoSystem 3
Installing BeoLab 10
Setting-up PDP settings
Installation on the
Japanese market
Technical specications

Installation overview 5
Weight
When the TV or the stand needs to be moved, a crane can be used (recommended). The items are too heavy to move and it is strongly
recommended to not attempt lifting them manually.
! Only moving company are allowed to lift or move the TV and Floor Stand. Not technicians or installers.
There is no requirements to which type of crane to use, but in order to attain a
smooth and safe operation, it is recommended to use a crane like this:
L = 95-135 cm, length of reach
H = ≥ 235 cm (height)
W = ≥ 98 cm (width)
Hw = ≤ 18 cm (height of wheels)
The weight of BeoVision 4-85 is approx. 145 kg and approx. 260 kg for the Floor Stand.
It is recommended to use a crane which is approved to handle loads up to
350 kg at L = 135 cm for Floor Stand installations (155 cm for wall bracket installations).
The reason is to ensure a safe and steady operation.
Environment
It is strongly recommended to pay attention to the environment where the installation is going to take place. It is very important that all kinds of
precautions are made to prevent damages to the environment (oors, walls, furnitures etc.).
Placement
Be sure that the surface where the product is going to be placed, is plane and the building design meets the required loads.
!It is very important that the oor is level, and all eight feets under the plate are correctly adjusted.
L
H
W
Hw