Bang & Olufsen BEOLAB 8002 User manual

BeoLab 8002
Guide

WARNING: To reduce the risk of fire or
electric shock, do not expose this appliance
to rain or moisture. Do not expose this equip-
ment to dripping or splashing and ensure
that no objects filled with liquids, such as
vases, are placed on the equipment.
To completely disconnect this equipment
from the AC Mains, disconnect the mains
plug from the wall socket. The disconnect
device shall remain readily operable.
The lightning flash with arrowhead symbol
within an equilateral triangle, is intended
to alert the user to the presence of un-
insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.

Daily use
When you have finished setting
up the loudspeakers as described
on the following pages, connect
the entire system to the mains
supply. The indicator lights up
in red, indicating that the loud-
speakers are in standby, ready to
be used. The loudspeakers are
designed to be left in this
standby mode when not in use.
Switching on and off –
indicator
When you switch on your Bang&
Olufsen system, the loudspeakers
switch on simultaneously. The red
standby indicator light turns green,
indicating that the loudspeakers
are switched on.
When you switch off your system, or
mute the sound, the red indicator
light appears immediately,
indicating that the loudspeakers
are not in use.
If the loudspeakers are connected
to a non-Bang& Olufsen system,
they switch on when they receive a
signal from the system (refer to
p.6). They switch off a few
minutes after the signal has
disappeared.
Loudspeaker protection
The loudspeakers are equipped
with a thermal protection system
which prevents overheating. If an
error occurs – or the speaker units
become overheated – the system
automatically switches the loud-
speakers to standby, and the
indicator light turns orange.
To restore the situation:
> Disconnect the loudspeakers
from the mains.
> Allow the system time to reset
(approximately 3–5 minutes).
> Reconnect the loudspeakers to
the mains.
Should the problem persist, contact
your Bang & Olufsen retailer.
Cleaning the loudspeaker
Wipe dust off the surfaces using a
dry, soft cloth. If necessary, remove
stains or dirt with a soft, damp cloth
and a solution of water and mild
detergent such as washing-up
liquid.
Never use alcohol or other solvents
to clean any part of the loud-
speakers!
3
NOTE! Prolonged listening at high
volume levels may cause hearing
damages.
Indicator

Set up the loudspeaker
We recommend that you follow
this procedure:
– Disconnect your system from the
mains supply.
– Place the loudspeakers in your
setup.
– Set the switches to the correct
setting. This is explained in ‘Adapt
the loudspeakers to your setup’
(page6).
– Connect your speaker system.
– Connect the entire system to the
mains again.
If you mount the loudspeaker on a
wall bracket, you cannot assemble
the base to the loudspeaker.
Cautions
– Make sure that the loudspeakers
are placed and connected in
accordance with the instructions
in this Guide. To prevent injury,
use Bang & Olufsen approved
stands and wall brackets only!
– The loudspeakers can only be
switched off completely by
disconnecting them from the
wall socket.
– The loudspeakers are designed
for indoor use in dry, domestic
environments only, and for use
within a temperature range of
10–40º C (50–105º F).
– Remember that all speakers in a
setup must be connected to a
mains outlet, and that they are
designed to be connected to the
mains at all times, as this allows
them to switch on automatically.
– Do not attempt to open the loud-
speaker. Leave such operations
to qualified service personnel!
Column and base
It is easiest to assemble the base and
the speaker column if the loud-
speaker is placed on the two foam
packaging blocks – as shown.
Remove the small plastic cylinder
from the threaded end of the loud-
speaker, and push the base onto
the threaded end. Fasten the base
to the column with the washer and
nut. Tighten the nut carefully.
4
NOTE! The type number of the
loudspeaker appears on the label
which is placed on the inside of the
socket panel cover.

Cable connections
The loudspeakers can be used
with Bang& Olufsen audio,
video and link systems. They may
also be used with non-Bang&
Olufsen systems. For specific
information about the sockets on
your system, refer to the Guide
enclosed with the system.
Mains cord: The supplied mains
cord and plug are specially designed
for the product. If you change the
plug or damage the mains cord,
you must buy another from your
Bang& Olufsen retailer!
Place the cable cover around the
cables as shown on page8.
Pull the small lid and then lift it up to
gain access to the socket panel.
For safety reasons you must fasten
the mains lead to the black lid using
the enclosed cable-tier (A).
A
SETUP
L
R
LINE
POSITION
5
Connection to the
mains supply
SETUP switch
L–R–LINE
POWER LINK socket
POSITION switch
– –

Adapt the loudspeakers to your setup
The loudspeakers may be placed
almost anywhere in your room.
However, the most natural
sound is obtained if they are set
up as explained in this section. SETUP switch
This switch has three settings: LEFT,
RIGHT and LINE. Set the switch to
LEFT or RIGHT when connecting
the loud speakers in a Bang&
Olufsen system. Set the switch to
LINE when connecting the loud-
speakers in a non–Bang& Olufsen
system.
…To a Bang& Olufsen system:
Use Bang& Olufsen Power Link
cables to connect the loudspeakers
to your system. Set the SETUP
switch to LEFT and RIGHT (the left
and right sound channel)
respectively.
…To a non-Bang& Olufsen
system:
Use a special adaptor with an
ordinary phono/RCA plug in one
end, and a DIN-plug in the other.
Depending on your setup, you may
also need to connect an adaptor
with phono/RCA and mini jack
plugs (optional accessories,
available from your Bang& Olufsen
retailer). Set the SETUP switch to
LINE.
POSITION switch
When a loudspeaker is placed in a
corner or close to a wall, the bass
level is boosted compared to the
bass level from a loudspeaker placed
in a more free-standing position.
To remove this excessive bass boost,
set the POSITION switch to ensure
that the bass level suits the
placement of the loudspeaker. The
appropriate switch setting depends
on the distance from the loudspeaker
to the walls and corners of the room.
Use the guidelines on the next page,
when deciding which of the three
POSITION switch settings to select
– on each loudspeaker.
The position zones, shown on the
next page, are meant as guidelines
– you may, of course, set the switch
to any of the three settings you
prefer.
SETUP
L
R
LINE
POSITION
SETUP
L
R
LINE
POSITION
6

The POSITION switch has three
settings: free, wall and
corner.
free
Use this setting if the loudspeaker is
placed more than 15cm (6") from
the wall, and no closer to a corner
than 50cm (20") – shown by the
large light grey area in the
illustration.
wall
Use this setting if the loudspeaker
is placed less than 15cm (6") from
the wall, and no closer to a corner
than 50 cm(20") – shown by the
grey areas along the walls in the
illustration.
If the loudspeaker is mounted on a
wall bracket, use this setting.
corner
Use this setting if the loudspeaker
is placed in a corner – shown by the
dark grey areas in the illustration.
How to measure? The distances
referred to are measured as shown
here (the loudspeaker seen from
above).
7
Position zones: The three settings
(free, wall and corner) correspond
to the position zones marked in
different shades of grey.

>> Adapt the loudspeakers to your setup
Cable cover: The rubber tube
packed with the loudspeakers is a
cable cover specially designed for
the loudspeakers. Use the enclosed
tool to “zip up” the cable cover
when you have placed both the
mains cord and the Power Link
cable inside it.
The special adaptor, part no.
6270706, can be used to connect
additional pairs of loudspeakers to
your Bang& Olufsen system. The
adaptor is available as an optional
accessory from your Bang& Olufsen
retailer.
8

Waste Electrical and Electronic
Equipment (WEEE) –
Environmental protection
Electrical and electronic equipment,
parts and batteries marked with
this symbol must not be disposed
of with normal household wastage;
all electrical and electronic equip-
ment, parts and batteries must be
collected and disposed of separately.
When disposing of electrical and
electronic equipment and batteries
by use of the collection systems
available in your country, you
protect the environment, human
health and contribute to the
prudent and rational use of natural
resources. Collecting electrical and
electronic equipment, batteries
and waste prevents the potential
contamination of nature with the
hazardous substances which may
be present in electrical and elec-
tronic products and equipment.
Your Bang & Olufsen retailer will
advise you of the correct way of
disposal in your country.
If a product is too small to be
marked with the symbol, it will
appear in the User Guide, on the
Guarantee certificate, or on the
packaging.
This product is in conformity with the provisions of the Directives
2004/108/EC and 2006/95/EC.
Technical specifications, features and the use thereof are subject to
change without notice!
All Bang& Olufsen products comply with applicable environ mental
legislation throughout the world.
9