Bang & olufsen Beoplay v1-32 User manual

BEOPLAY V1

BeoPlayV1–32

BeoPlayV1–40

This Getting Started contains information about the setting up and daily use of your

B&O PLAY product and connected equipment.

Your television offers more features and functions than described in this Getting

Started. Among other things; Sleep Timers, pin code system and network settings.

These and other features are described in more detail in the product’s online guide

or in the help texts in the television menus.

The guides are found on www.beoplay.com/v1/support.

The guides and the on-screen help texts are also kept up to date if new software

introduces new or modied features and functions in your television.

On www.beoplay.com/v1 you can also nd more information and relevant FAQs

(Frequently Asked Questions) about your product.

Your retailer is your rst stop for all your service queries.

Dear Customer

Technical specications, features and the use

thereof are subject to change without notice.

3511008 Version 1.0 1201

Cautions

– Ensure that the television is positioned, set up

and connected in accordance with the

instructions in this Getting Started. To prevent

injury, use Bang & Olufsen approved stands and

wall brackets only!

– Place your television on a rm, stable surface.

– Do not place any items on top of your television.

– Do not subject the television to rain, high

humidity or sources of heat.

– The television is intended for indoor use in dry,

domestic environments only. Use within a

temperature range of 10–40°C (50–105°F)

– If the television has been exposed to

temperatures below 5°C (40°F), leave it at room

temperature and wait until the television has

regained normal room temperature before it is

connected to the mains and switched on.

– Do not place the television in direct sunlight or

direct articial light, such as a spotlight, as this

may reduce the sensitivity of the remote control

receiver. Also if the screen is overheated, black

spots may appear in the picture. These spots

disappear again, once the television cools down

to normal temperature.

– Leave enough space around the television for

adequate ventilation.

– No naked ame sources, such as lighted candles

should be placed on the apparatus.

– To prevent the spread of re, keep candles or

other open ames away from this product at all

times.

– Do not attempt to open the television. Leave

such operations to qualied service personnel.

–

Do not strike the glass with hard or pointed items.

–

The television can only be switched off completely

by disconnecting it from the mains socket. The

mains socket must always be accessible.

– Follow instructions to ensure correct and safe

installation and interconnection of equipment in

multimedia systems.

– The product label is placed behind the

connection cover.

Contents

Setting up

6 How to set up your television

8 Connection panel – BeoPlayV1–32

10 Connection panel – BeoPlayV1–40

Daily use

12 How to use your remote control

13 How to navigate in menus

15 Watch television

16 Media browser

17 Change picture or sound settings

18 Cleaning

19 How do I…

How to set up your television

Important – guides and FAQs are found on www.beoplay.com/v1/support

– To remove the connection cover, pull out at the

bottom rst to release the cover, then pull it off.

– Connect the mains cord, Ethernet cable and the

aerial or satellite cable depending on your setup.

For a wireless connection (optional), see

below.*1

– Switch on the television (press TV). If prompted

for a pin code, enter the pin code provided by

your retailer and continue with rst-time setup

(see next page).

Unpack the television and place it on a soft

blanket. Remove the four pins from the television.

Before mounting the stand or wall bracket,

remember to insert the speaker cover. Hold the

speaker cover with both hands and slide it

carefully into the hole on the side of the television.

Then mount the stand or wall bracket

(see separate guide).

3.Connect your TV

1.Unpack the television

2.Insert speaker cover and mount

stand/wall bracket

Guides and more information, for example, FAQs (Frequently Asked Questions) are

found on www.beoplay.com/v1/support.

To remove the speaker cover, gently push it out

using one of the four pins removed from the

television. If the television is mounted on the table

stand or wall bracket, you must rst remove the

sides on the stand or wall bracket to remove the

speaker cover. See the guides enclosed with the

stand or wall bracket.

To ensure proper ventilation, allow enough space around the screen. Do not cover the ventilation grill. At over heating

(ashing

standby indicator and an on-screen warning), switch the TV to standby, not off, in order for the TV to cool down. You

cannot operate the TV during this time.

Connect your television to the Internet to receive software updates and download Peripheral Unit Controller (PUC) tables.

It is recommended that you set the television to update software automatically.

A wireless setup requires that your television has a built-in wireless module and that you have purchased a wireless

network antenna. For more information, see the online guide.

Ventilation

Ethernet connection

1*Wireless setup

WLAN

ANTENNA

AERIAL

SATELLITE

5V 50mA

Aerial/cable/analogue

signal

Mains supply

Wireless network

antenna

Satellite

signal

Ethernet

Setting up

You can fasten the cables to either sides or in the

middle, depending on stand or wall bracket

placement. For safety reasons, secure the cables

with the enclosed cable ties.

When you have made all the connections, mount

the connection cover.

6.Run cables

If you have a wall bracket, make sure that there is

enough slack in the cables to allow the TV to turn

before you fasten the cables with cable ties to

make a neat bundle.

Follow on-screen instructions. When available, press the blue button

for help texts.

MENU LANGUAGE

SOFTWARE UPDATE (USB)

COUNTRY

LANGUAGE

NETWORK SETTINGS

SOFTWARE UPDATE (INTERNET)

SPEAKER SETTINGS

ACCESS CONTROL

INPUTS (TV TUNING)

NICE TO KNOW

4.First-time setup

You will be guided through a number of menus

where you must make different settings. Use the

Beo4 navigation button ,,and , and press

in the middle to select settings. In some

submenus, press BACK to return to rst-time

setup.

You can change the settings again later if you

wish. If you receive your TV signal via a set-top

box, select NONE in INPUTS. Set up your set-top

box as illustrated below.

The illustration here is only one example of many

possible setups.

When you connect external equipment, for

example a set-top box, to the HDMI IN socket on

the television (see next pages), you are prompted

to congure the source. Follow on-screen

instructions.

For information on other setup options, PUC

tables and IR-transmitters, see the online guide

available on www.beoplay.com/v1/support.

5.Connect external equipment

For information on your Beo4 remote control, see page12 or your Beo4 guide.

The indicator light ashes green shortly and the TV is ready to be used. To reduce start up time, see the online guide

regarding power settings.

The TV is in standby but leave it connected to the mains supply due to software downloads.

The TV has been disconnected from the mains supply and you must enter the pin code. See the online guide for more

information on the pin code system, available on www.beoplay.com/v1/support.

Do not disconnect the TV from the mains supply. Could be due to new software being activated or too many failed pin

code attempts.

The TV is in standby and you can disconnect it from the mains supply if you want. However, this activates the pin code

system.

Indicator light – Green

Solid red

Slowly ashing red

Quickly ashing red

Off

BACK

INTERNET

PUCHDMI

ETHERNET

It is possible to control non-Bang&

Olufsen equipment using the Beo4

remote control with a Peripheral

Unit Controller (PUC) table. For PUC

to work, an IR-transmitter must be

placed close to the IR-receiver on

the connected equipment. Check

the IR-signal before attaching the

IR-transmitter.

Indicator light

Connection panel – BeoPlayV1–32

Important

Any equipment you connect to the connection panel must be registered in the

SOURCE LIST SETUP menu.

Mains cord and plug Connect the ~socket on the connection panel of your TV to the wall outlet.

The TV is in standby mode and ready to be used.

The supplied plug and mains cord are specially designed for the product. Do

not change the plug and if the mains cord is damaged, you must buy a

Bang& Olufsen approved mains cord.

1*Make sure the cable connection between the

product and the router does not exit the building

to avoid contact with high voltage.

Ethernet ( )*1

For connection to the Internet.

For software updates or for

UPnP streaming of digital photos,

video or music les from, for

example, a NAS device

SATELLITE (14/18V – 0.4A)

Aerial input socket for a digital satellite signal.

Depending on your tuner options, you may have

either one or no satellite socket. Never connect an

optional active antenna here

2 x COMMON INTERFACE (CA Module)

For insertion of a CA module and smart card

for access to coded digital channels. For more

information about compatible smart card and

CA module combinations, contact your

retailer. See the online guide for information

on correct insertion*2

USB ( , 5V – 0.5A)

For connection of a

USB device to browse

digital photos, video or

music les

AERIAL (5V – 50mA)

Aerial input socket for an

external aerial/cable TV network

or for an analogue signal

~ –Mains supply

Connection to the

mains supply

ANTENNA WLAN

For connection of wireless

network antenna (optional)

WLAN

ANTENNA

AERIAL COMMON INTERFACE

SATELLITE

CHIPSIDE

5V 50mA

Setting up

PL1–3 (Power Link)

For connection of external

speakers in a surround sound

setup. See the online guide for

more information*2

HDMIIN (1–5)

The High Denition Multimedia Interface

allows you to connect many different

video sources, such as set-top boxes,

game consoles, multimedia players, Blu-

ray players, or a PC

S/P-DIFIN

Digital audio input

socket

PUC1 A+B (CTRL2)/PUC2 A+B (CTRL3)

For IR control signals to external equipment connected

to an HDMIIN or AV IN socket. Allows you to control

non-Bang& Olufsen equipment with a Beo4 remote

control with navigation button*2

CTRL1

Not in use

AVIN

For connection of analogue video

equipment. Special adaptor needed

Cables and adaptors

Ethernet connection

2*Online guide

Depending on the type of equipment you connect to the television, different cables and maybe also

adaptors are needed. Cables and adaptors are available from your Bang& Olufsen retailer.

Connect your television to the Internet to receive software updates and download Peripheral Unit

Controller (PUC) tables. It is recommended that you set the television to update software automatically.

The online guide includes more information about setup and connection of external equipment.

We recommend that you connect the television to the Internet to be able to

receive software updates and to download Peripheral Unit Controller (PUC) tables.

PUC tables enable you to operate connected non-Bang& Olufsen products with

the Beo4 remote control with navigation button.

54321

CTRL 1

S/P-DIF

IN HDMI IN

CTRL 2

PUC 2 A+B

CTRL 3

PUC 1 A+B PL 1PL 2PL 3

Any equipment you connect to the connection panel must be registered in the

SOURCE LIST SETUP menu.

Connection panel – BeoPlayV1–40

USB ( , 5V – 0.5A)

For connection of a USB

device to browse digital

photos, video or music

les

Ethernet ( )*1

For connection to the Internet. For

software updates or for UPnP

streaming of digital photos, video or

music les from, for example, a NAS

device

SATELLITE (14/18V – 0.4A)

Aerial input socket for a digital

satellite signal. Depending on your

tuner options, you may have either

one or no satellite socket. Never

connect an optional active antenna

here

AERIAL (5V – 50mA)

Aerial input socket for an external aerial/

cable TV network or for an analogue

signal

2 x COMMON INTERFACE (CA Module)

For insertion of a CA module and smart card for

access to coded digital channels. For more information

about compatible smart card and CA module

combinations, contact your retailer. See the online

guide for information on correct insertion*2

Important

Mains cord and plug Connect the ~socket on the connection panel of your TV to the wall outlet.

The TV is in standby mode and ready to be used.

The supplied plug and mains cord are specially designed for the product. Do

not change the plug and if the mains cord is damaged, you must buy a new

one from your Bang& Olufsen retailer.

1*Make sure the cable connection between the

product and the router does not exit the building

to avoid contact with high voltage.

AERIAL COMMON INTERFACE

SATELLITE

CHIPSIDE

5V 50mA

Setting up

~ –Mains supply

Connection to the

mains supply

ANTENNA WLAN

For connection of wireless

network antenna (optional)

PL1–3 (Power Link)

For connection of external

speakers in a surround sound

setup. See the online guide for

more information*2

HDMIIN (1–5)

The High Denition Multimedia

Interface allows you to connect many

different video sources, such as set-top

boxes, game consoles, multimedia

players, Blu-ray players, or a computer

S/P-DIFIN

Digital audio input

socket

PUC1 A+B (CTRL2)/PUC2 A+B (CTRL3)

For IR control signals to external equipment

connected to an HDMIIN or AVIN socket. Allows

you to control non-Bang& Olufsen equipment

with a Beo4 remote control with navigation

button*2

CTRL1

Not in use

AVIN

For connection of

analogue video

equipment. Special

adaptor needed