Bante Instruments TB200 User manual

TB200 Laboratory Turbidity Meter
USER MANUAL
Bante Instruments Inc.

1IOverview
Introduction
Thank you for selecting the TB200 laboratory turbidity meter. This user
manual provides a step-by-step guide to help you operate the meter,
please carefully read the following instructions before use. Any use
outside of these instructions may invalidate your warranty and cause
permanent damage to the meter.
Environmental Conditions
Before unpacking, ensure that current environmental conditions meet
the following requirements.
•Relative humidity is less than 80%
•Ambient temperature between 0°C (32°F) and 50°C (122°F)
•No ambient light and electromagnetic interference
Packing List
The following list describes all components of the meter. If any items
are missing or damaged, contact the supplier immediately.
TB200 turbidity meter
Formazin standard solutions 0.02, 200, 500, 1000 NTU
Two sample vials
Lint-free cloth
12V DC power adapter
Meter Overview
1 Light shield lid
2 Measurement chamber
3 Display
4 Membrane keypad
Connectors
1 Socket for power adapter
2 USB-B interface to computer
Keypad
Key
Function
•Switch the meter on or off
•Exit the calibration, settings, data logs and return
to the measurement mode
•Start calibration
•Press and hold the key to enter the setup menu
•Store current reading to memory
•Increase value or scroll up through a list of options
•View the data logs
•Decrease value or scroll down through a list of
options
Confirm the calibration or displayed option
•Start measurement
•Lock or unlock the measurement
Switching the Meter On and Off
•Connect the 12V DC power adapter to the meter and wall outlet.
•Press the key and release to switch on the meter.
•Press and hold the key to switch off the meter.
Prior to Use
Switch on the meter and wait 10 minutes for meter to warm up.

Setup I2
Meter Setup
The TB200 turbidity meter contains an integrated setup menu for
customizing the displayed option to meet measurement requirements.
The following table describes the functions of each menu item.
Setup Menu
Date and Time
Set the year, month, day, hour, minute for data log.
Measurement Mode
Select the desired measurement mode and unit.
NTU Nephelometric turbidity unit (default)
FNU Formazin nephelometric unit
EBC Turbidity unit of the European Brewing Convention
ASBC Turbidity unit of American Society of Brewing Chemists
mg/L Total suspended solids unit
Resolution
Set the resolution of the turbidity measurement.
0.1 default
0.01
TSS Factor
Set the conversion factor for measurement of the total suspended
solids.
0.13 default
Auto-Power Off
If enabled, the meter will automatically switch off if no key is pressed
within 2 hours.
2 hours default
Disable
Delete Data
Delete all data logs in the memory.
Delete all stored data
Cancel default
Brightness
Set the brightness level of backlight.
Password
Set the password protection for setup menu and calibration.
Enable
Disable default
Reset
Reset the meter to factory default settings. Note, the meter must be
recalibrated.
Enable
Disable default
Setting a Default Option
1.1 Press and hold the key to enter the setup menu.
1.2 Press the / key to select a menu item or an option.
1.3 Press the Enter key to save.
To exit the setting without saving changes, press the ESC key.
Setting the Password
The password protection feature is used to prevent the unauthorized
calibration and settings. If enabled, the user must enter a 4-digit
password to enter the setup menu or calibration mode.
2.1 Press and hold the key to enter the setup menu.
2.2 Press the key to select the
Password , press the Enter key to
confirm.
2.3 Press the key to select the
Enable . Press the Enter key, the
screen shows 0000 and the cursor appears below the first digit.
2.4 Press the / key to set the password, press the Enter key
to confirm until the meter returns to the measurement mode.
Unlock the Password
If your password has created, the meter will show Password Protection
screen when pressing the Cal key. Press the / key to enter
the password, press the Enter key to confirm, the meter will unlock
immediately. If you forgot your password, please contact supplier and
providing the serial number of the meter.

3ICalibration
Factory Reset
The Reset feature is used to restore the meter back to factory default
settings. If enabled, all of the calibration data and selected options
will be deleted or reset, the meter must be recalibrated.
Note, the data logs will not be deleted.
3.1 Press and hold the key to enter the setup menu.
3.2 Press the key to select the
Reset , press the Enter key to
confirm.
3.3 Press the key to select the
Restore Factory Settings . Press the
Enter key, the screen shows "Are you sure you want to restore
factory settings? ".
3.4 Press the Enter key to confirm or the ESC key to cancel.
Measurement and Calibration Hints
•Never pour the sample directly into the measurement chamber
and using a vial to perform measurement.
•Make sure the sample in vial is homogeneous. Do not shake or
agitate the solution violently to prevent air bubbles.
•Keep the outside of vial clean and dry. If necessary, wipe the vial
with a lint-free cloth.
•If the vial has scratches or scuffs, replace a new one (order code
TB-GV).
•During the calibration and measurement processes, make sure
the vial is positioned in the measurement chamber and the
triangle mark on the vial must be aligned with the arrow on the
meter.
•Always close the light shield lid to prevent the measurement
errors from ambient light.
•Wash the sample vial with distilled water after measurement.
Any residues can cause inaccurate readings.
Turbidity Calibration
The TB200 turbidity meter allows turbidity calibration up to 7 points
with minimum of 2 points, the default calibration points include the
0.02, 10, 200, 500, 1000, 1500 and 2000 NTU. For better accuracy, we
recommend to select a calibration point close to the sample value you
are measuring. Note, the meter is calibrated with Formazin Standards
at the factory and does not require user calibration before use.
Calibrating the Meter
1. Press the Cal key to enter the calibration mode. Press the /
key to select the number of calibration points.
2. Press the Enter key, the screen shows 0.02 NTU. If necessary,
press the / key to select first calibration point, the meter
will perform the calibration from the low to high turbidity.
3. Take out the corresponding turbidity standard from accessory box
(e.g., 0.02 NTU), wipe the vial with a lint-free cloth to remove
fingerprints. Hold the vial cap and gently inverting vial several
times, ensure that the turbidity standard is homogeneous and no
air bubbles.
4. Insert the vial into the measurement chamber. Align the triangle
mark on the vial cap with the arrow on the meter. Close the light
shield lid.
Align arrows
Mark
Arrow

Measurement I4
5. Press the Enter key, the meter begins calibration. The Calibrating
icon shows on the upper right corner of the screen.
When the reading stabilizes, the meter will automatically show
next calibration point.
If necessary, press the key to select a desired calibration point.
6. Repeat steps 3 through 5 until the screen shows "Calibration is
Completed", the meter returns to the measurement mode.
To exit the calibration without saving calibrated values, press the ESC
key.
Turbidity Measurement
An accurate turbidity measurement depends on good measurement
techniques. Factors such as clean sample vial, positioning of vial in
the measurement chamber, covering the vial with the light shield lid,
meter calibration, removal of bubbles, etc. Refer to the Measurement
and Calibration Hints section for detailed instructions on page 3.
Measuring the Low Turbidity Sample
For the low turbidity samples (< 200 NTU), we recommend that using
the same vial to perform the calibration and measurement.
1.1 Rinse the vial with approximately 10 ml of sample. Cap and upend
the vial several times. Discard the used sample and repeat the
rinsing procedure two more times.
1.2 Fill the vial with the sample. Cap the vial and wipe with a lint-
free cloth to remove waterdrops and fingerprints. Hold the vial
cap and gently inverting vial several times, ensure that the sample
is homogeneous and no air bubbles.
1.3 Insert the vial into the measurement chamber. Align the triangle
mark on the vial with the arrow on the meter. Close the light
shield lid.
1.4 Press the Meas key, the meter begins measurement, the
icon shows on the screen. When the reading stabilizes, the icon
will automatically switch to .
1.5 If necessary, press the Meas key to take a new measurement.
During the measurement, press the key, the reading will be locked.
Press the key again to resume measurement.
Align arrows

5IMeasurement
Measuring the High Turbidity Sample
For the high turbidity samples (>1100 NTU), the solution must be diluted
before measurement. The dilution water can be obtained by filtering
distilled water through a < 0.45 µm filter membrane.
2.1 Repeat steps 1.1 through 1.4 above and record the reading.
2.2 Calculate the true turbidity of the original sample using the
following formula.
T = [Td(Vs+ Vd)] / Vs
Where:
T = Ture turbidity of the original sample
Td= Measured value
Vs= Volume of the original sample (ml)
Vd= Volume of the dilution water (ml)
Total Suspended Solids
Measurement
The TB200 turbidity meter contains a Total Suspended Solids mode
and needs to enter a conversion factor before measurement.
Calculating the TSS Factor
1. Rinse the filter disk with distilled water to remove any solids that
may remain. Put the filter disk in a watch glass and dry them in
a 104°C (219°F) drying oven for 1 hour.
2. Remove the filter disk and watch glass and put in a desiccator.
Immediately cover the desiccator. Wait for them decrease to
room temperature.
3. Weigh the filter disk and watch glass and record the mg value
as B.
4. Filter the 100 ml of sample through pre-weighed filter disk. Put
the filter disk and watch glass in a 104°C (219°F) drying oven for
1 hour.
5. Remove the filter disk and watch glass and put in a desiccator.
Immediately cover the desiccator. Wait for them decrease to
room temperature.
6. Weigh the filter disk and watch glass and record the mg value
as A.
7. Calculate the TSS value using the formula below.
TSS (mg/L) = (A - B) / 0.1
8. Fill the vial with the sample.
9. Repeat turbidity measurement steps 1.1 through 1.5 and record
the NTU value. Calculate the TSS conversion factor using the
formula below.
Factor = NTU / TSS (mg/L)
Setting the TSS Factor
1. Press and hold the key to enter the setup menu.
2. Press the key to select the
TSS Factor , press the Enter key to
confirm.
3. Press the / key to set the conversion factor, press the Enter
key to save.
Selecting the TSS Measurement Mode
1. Press and hold the key to enter the setup menu.
2. Press the key to select the
Measurement Mode , press the
Enter key to confirm.
3. Press the / key to select the
mg/L (TSS) , press the Enter
key to enter the Total Suspended Solids measurement mode.

Data Management I6
TSS Measurement
The measurement method of the Total Suspended Solids is the same
as the turbidity. Refer to the Turbidity Measurement section for
detailed instructions on page 4.
Data Management
Storing a Measurement Result
In the measurement process, press the MI key to store the reading
into the memory, the screen will show "Data is stored in memory".
Viewing the Data Logs
1.1 Press the MR key in the measurement mode, the screen shows
the stored readings.
1.2 Press the / key to switch pages.
1.3 Press the ESC key, the meter returns to the measurement mode.
Deleting the Data Logs
If the memory is full, the meter will automatically show a reminder
when the MI key is pressed. To delete data logs, please follow the
steps below.
2.1 Press and hold the key to enter the setup menu.
2.2 Press the / key to select the Delete Data , press the Enter
key to confirm.
2.3 Press the / key to select the
Delete all stored data , press
the Enter key, the screen shows "Are you sure you want to delete
all stored data?".
2.4 Press the Enter key to confirm or the ESC key to cancel.
Communication
The TB200 turbidity meter is capable of transferring the data to the
computer or importing the data to Excel by a free DAS software. You
are able to download this software from our official website. Before
installation, ensure that the Windows 10 operating system has been
installed on your computer.
Receiving the Data
1. Connect the USB cable to the meter and computer.
2. Click the DAS icon, the system automatically scans an available
communication port and shows a message box "Found a port on
your computer".
3. Click the OK, the application starts.
4. Click the Connect, the screen shows "Port is connected".
5. Click the OK, then click the Receive, the stored data will transfer
to computer automatically.
If your computer can not find a communication port, please click the
file "CP210xVCPInstaller_x64.exe or CP210xVCPInstaller_x86.exe" to
update the drive program.
Creating an Excel File
When the transfer is completed, click the Save as Excel button, the
readings in data sheet will automatically convert to Excel file.
Note, once the software is closed, all received data will be lost and
can not be recovered.
Appendix
Indexing a Sample Vial
The United States Environmental Protection Agency recommends that
the vial used for turbidity calibration or sample measurement be
indexed. Its purpose is to obtain a position which provides the lowest
turbidity reading. The indexing methods are as follows.
1.1 Fill the vial with the distilled water (< 0.5 NTU). Cap the vial.
1.2 Wipe the vial with the lint-free cloth. Ensure that the outside of
vial is clean and dry.
1.3 Place the vial in the measurement chamber. Align the triangle
mark on the vial with the arrow on the meter.
1.4 Press the Meas key, the meter begins the measurement.
1.5 Slowly rotate the vial approximately 45°. Close the light shield
lid and record the reading.
1.6 Repeat the step 1.5 until the lowest turbidity reading is shown.
Mark this position on the vial.

7IAppendix
Matching the Sample Vials
For better accuracy and repeatability, using an indexed sample vial is
best choice for turbidity measurement. If you need to use a few vials,
match these vials are necessary.
2.1 Repeat steps 1.1 through 1.6 above for each vial and record the
readings.
2.2 Find the closest position of these vials measuring value and mark
it.
Preparation of Formazin Standards
Turbidity-Free Water:
The turbidity-free water is used for preparation of turbidity standards
and is prepared by filtering distilled water through a 0.45 µm or smaller
pore-sized membrane.
Turbidity Standards:
4000 NTU: Dissolve 1 gram hydrazine sulfate (NH2)2• H2SO4in the
turbidity-free water and dilute to 100 ml in a volumetric flask.
Dissolve 10 grams hexamethylenetetramine (CH2)6N4in the turbidity-
free water and dilute to 100 ml in a volumetric flask.
Mix 5 ml of hydrazine sulfate and 5 ml of hexamethylenetetramine
solutions in a 100ml volumetric flask and let stand 24 hours at 25/±3°C.
2000 NTU: Mix 50 ml of 4000 NTU standard in a 100 ml volumetric
flask and dilute to the mark.
1500 NTU: Mix 37.5 ml of 4000 NTU standard in a 100 ml volumetric
flask and dilute to the mark.
1000 NTU: Mix 25 ml of 4000 NTU standard in a 100 ml volumetric
flask and dilute to the mark.
500 NTU: Mix 12.5 ml of 4000 NTU standard in a 100 ml volumetric
flask and dilute to the mark
200 NTU: Mix 10 ml of 4000 NTU standard in a 100 ml volumetric
flask and dilute to the mark. Mix 50 ml of above standard in a 100 ml
volumetric flask and dilute to the mark.
10 NTU: Mix 2.5 ml of 200 NTU standard in a 100 ml volumetric flask
and dilute to the mark.
- Or -
Mix 2 ml of 500 NTU standard in a 100 ml volumetric flask and dilute
to the mark.
Optional Accessories
Order Code Description
TB-GV Glass sample vial, 60(H)×25(Dia) mm (2.36×0.98 in.)
TB-CAL Turbidity standards 0.02, 200, 500, 1000 NTU, 20 ml
USB-B USB connector A to B, 1 m (3.3 ft) cable
DCPA-12V 12V DC power adapter, european standard plug
Specifications
Model
TB200
Measurement Method
ISO 7027 nephelometric method (90°)
Range
0 to 2000 NTU/FNU
0 to 500 EBC
0 to 9999 ASBC
TSS range depends on conversion factor
Resolution
0.01 NTU (0 to 99 NTU)
0.1 NTU (100 to 999 NTU)
1 NTU (1000 to 2000 NTU)
Accuracy
±2% of reading (0 to 500 NTU),
±3% of reading (501 to 2000 NTU)
Calibration Points
2 to 7 points
Calibration Standards
0.02, 10.00, 200, 500, 1000, 1500, 2000 NTU
Light Source
Infrared-emitting diode (850nm wavelength)
Detector
Silicon photodiode
Stray Light
< 0.02 NTU
Sample Vial
60 (H) × 25 (Dia) mm (2.36 × 0.98 in.)
Sample Volume
20 ml
Memory
200 data sets
Communication
USB interface
Operating Temperature
0 to 50°C (32 to 122°F)
Storage Temperature
0 to 60°C (32 to 140°F)
Relative Humidity
< 80% (non-condensing)
Display
4.5 in. TFT LCD
Power Requirements
12V/2A DC power adapter
Dimensions
250 (L) × 177 (W) × 96 (H) mm
(9.8 × 6.9 × 3.7 in.)
Weight
1.2 kg (2.6 lb)

The information in this document is subject to change without notice.
Copyright © Bante Instruments Inc, 2022. All rights reserved.
Disposal
This product is required to comply with the European Union’s Waste
Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC and
may not be disposed of in domestic waste. Please dispose of product
in accordance with local regulations at the collecting point specified
for electrical and electronic equipment.
Warranty
The warranty period for meter is one year from the date of shipment.
Above warranty does not cover the turbidity standards and glass vials.
Out of warranty products will be repaired on a charged basis.
The warranty on your meter shall not apply to defects resulting from:
•Improper or inadequate maintenance by customer
•Unauthorized modification or misuse
•Operation outside of the environment specifications of the
products.
For more information, please contact the supplier.
Office: 4715 Castlewood St., Sugar land, TX 77479, USA
Tel: [phone]
E-mail: [email protected]
Factory: F3, Building 2, No.2185, Laifang Rd., Shanghai 201615, China
Tel: [phone]
E-mail: [e-mail]
www.bante-china.com