Barco Coronis Uniti MDMC-12133 User manual

Coronis Uniti
User Guide
MDMC-12133
K5902079/03
21/04/2015

Barco nv
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
PrintedinBelgium

Table of contents
TABLE OF CONTENTS
1. Welcome! .......................................................................................... 3
1.1 About the product ............................................................................................. 3
1.2 What’s in the box.............................................................................................. 3
2. Parts, controls and connectors ............................................................... 5
2.1 Display front view ............................................................................................. 5
2.2 Display rear view.............................................................................................. 6
2.3 Accessories.................................................................................................... 7
3. Display installation .............................................................................. 9
3.1 Removing the connector compartment cover.............................................................. 9
3.2 Unlocking the tilt mechanism ................................................................................10
3.3 Unlocking the height mechanism............................................................................10
3.4 Adjusting the display position................................................................................11
3.5 Connecting the signal cables ................................................................................12
3.6 Connecting the power cable .................................................................................14
3.7 Mounting the film clip .........................................................................................15
3.8 Mounting the MultiTouchPad.................................................................................16
3.9 Routing the cables & Reattach the connector compartment cover ......................................17
3.10 Fixation of the foot on the desk..............................................................................18
3.11 VESA-mount installation .....................................................................................19
3.12 First time starting up..........................................................................................22
4. Daily operation ................................................................................... 23
4.1 Recommendations for daily operation ......................................................................23
4.2 Key indicator lights............................................................................................24
4.3 Standby switching.............................................................................................24
4.4 Bringing up the OSD menus.................................................................................25
4.5 Navigating through the OSD menus ........................................................................25
4.6 Overview of the functionality of the Left/Right keys ... ..... .... .... .... ..... ..... .... .... .... ..... ..... ...26
4.7 I-Luminate .....................................................................................................27
4.8 Extended display keypad functions .........................................................................27
4.8.1 I-luminate mode .........................................................................................27
4.8.2 Viewing mode............................................................................................27
5. Advanced operation ............................................................................. 29
5.1 OSD menu language .........................................................................................29
5.2 OSD menu automatic close function........................................................................29
5.3 Power status indicator light ..................................................................................29
5.4 Key indicator lights............................................................................................30
5.5 Power lock function ...........................................................................................30
5.6 SoftGlow Task light ...........................................................................................30
5.7 SoftGlow Wall light............................................................................................31
5.8 DPMS mode...................................................................................................31
5.9 Hibernate.......................................................................................................32
5.10 I-Luminate default mode .....................................................................................32
5.11 I-Luminate film position.......................................................................................33
5.12 Luminance target..............................................................................................33
5.13 Color presets ..................................................................................................33
5.14 Color temperature.............................................................................................34
5.15 Color coordinates .............................................................................................34
5.16 Viewing modes................................................................................................34
5.17 Display functions..............................................................................................35
5.18 Ambient Light Compensation (ALC) ........................................................................36
5.19 Reading rooms ................................................................................................36
5.20 Continuous ALC...............................................................................................37
5.21 Embedded QA.................................................................................................37
5.21.1 About Embedded QA ...................................................................................38
K5902079 CORONIS UNITI 21/04/2015 1

Table of contents
5.21.2 DICOM status report ....................................................................................38
5.21.3 DICOM compliance check..............................................................................39
5.21.4 DICOM calibration.......................................................................................39
5.21.5 Reset DICOM calibration ...............................................................................39
5.21.6 DICOM error threshold..................................................................................40
5.22 Image scaling..................................................................................................40
5.23 Image source selection modes ..............................................................................40
5.24 Grayscale conversion modes................................................................................41
5.25 Input interface standard version.............................................................................41
5.26 EDID format ...................................................................................................42
5.27 EDID timings...................................................................................................42
5.28 Display info ....................................................................................................42
5.29 Display status..................................................................................................43
6. Cleaning your display ........................................................................... 45
6.1 Cleaning instructions .........................................................................................45
7. Important information ........................................................................... 47
7.1 Safety information.............................................................................................47
7.2 Environmental information ...................................................................................48
7.3 Regulatory compliance information .........................................................................50
7.4 EMC notice ....................................................................................................51
7.5 Explanation of symbols.......................................................................................54
7.6 Legal disclaimer...............................................................................................56
7.7 Technical specifications ......................................................................................56
7.8 Open source license information............................................................................58
2K5902079 CORONIS UNITI 21/04/2015

1. Welcome!
1. WELCOME!
1.1 About the product
Overview
Thank you for choosing this Coronis Uniti!
Coronis Uniti is an ingenious PACS display system designed to enhance flexibility and productivityindiag-
nostic imaging. Featuring the industry’s first 33-inch color LCD that can be used as two seamless heads
or one wide-screen display, Coronis Uniti offers you the freedom to organize your workspace just the way
you want it. It allows you to read radiology, mammography, and breast tomosynthesis images, side by
side on a single diagnostic screen. Coronis Uniti features Barco Optical Glass illuminated by DuraLight
Brilliance to provide an exceptional image over your entire field of view. Use the instructions in this guide
to install your Coronis Uniti display and discover the productive features and included accessories!
CAUTION:Read all the important safety information before installing and operating your
Coronis Uniti. Please refer to the dedicated chapter in this user guide.
1.2 What’s in the box
Overview
Your Coronis Uniti comes with:
• this Coronis Uniti user guide
• Quick Installation Sheet
• a system CD
• two DisplayPort cables
• a USB cable
• a set of AC power cords
• an external power supply
•Filmclip
• MultiTouchPad
If you ordered a Barco display controller, it’s also in the box together with its accessories. A dedicated
user guide is available on the system CD.
Keep your original packaging. It is designed for this display and is the ideal protection
during transport and storage.
K5902079 CORONIS UNITI 21/04/2015 3

1. Welcome!
4K5902079 CORONIS UNITI 21/04/2015

2. Parts, controls and connectors
2. PARTS, CONTROLS AND
CONNECTORS
2.1 Display front view
Overview
Image 2-1
Front view
1I-Luminate/Left key 2Right key
3Menu key 4Standby key
5Power status indicator light (Power On) 6Power status indicator light (Standby)
7I-Guard 8Ambient light sensor
K5902079 CORONIS UNITI 21/04/2015 5

2. Parts, controls and connectors
2.2 Display rear view
Connector compartment cover closed
Image 2-2
Rear view with closed connector compartment cover
1Connector compartment cover 2Tilt lock pin (only for transportation)
3Tilt & swivel foot 4Cable duct
5Foot lock pin (only for transportation) 6SoftGlow Task light
7SoftGlow Wall light
Store the foot lock pin and tilt lock pin for possible future transportation of the display.
6K5902079 CORONIS UNITI 21/04/2015

2. Parts, controls and connectors
Connector compartment cover open
Image 2-3
Rear view with open connector compartment cover
1Power connector 2Display port connector
3Display port connector 4Not used
5USB upstream connector 6USB downstream connector
7USB downstream connector 8USB downstream connector
2.3 Accessories
Film clip
The film clip can be used to hold a radiological film when using the I-Luminate function as a light box.
Image 2-4
Film clip
K5902079 CORONIS UNITI 21/04/2015 7

2. Parts, controls and connectors
MultiTouchPad
The MultiTouchPad enables and controls SpotView.
Image 2-5
MultiTouchPad
8K5902079 CORONIS UNITI 21/04/2015

3. Display installation
3. DISPLAY INSTALLATION
Prior to installing your Coronis Uniti and connecting all necessary cables, make sure to
have a suitable display controller physically installed in your computer. If you are using
a Barco display controller, please consult the user guide delivered with it to do this.
For a list of compatible display controllers, please refer to the latest version of the com-
patibility matrix available on my.barco.com (MyBarco > My Support > Healthcare > Com-
patibility Matrices > Barco Systems Compatibility Matrices).
3.1 Removing the connector compartment cover
The connector compartment cover should be removed to get access to the connectors.
To remove the connector compartment cover
1. Gently push the two lips on the top of the cover.
2. Pull the top of the cover slightly away from the display and lift the cover upwards.
3. Remove the cover.
K5902079 CORONIS UNITI 21/04/2015 9

3. Display installation
3.2 Unlocking the tilt mechanism
In the factory, the tilt system in the display stand is locked with a red pin to prevent dam-
age during transportation. You’ll have to remove this pin before adjusting your display
position.
Push the display against the buffer part to easily remove the pin.
To remove the pin:
1. Position the display with its rear side facing you.
2. Pull out the red pin in the display stand.
3. Keep the pin in case the display needs to be shipped later.
WARNING:Before transportation of the display, insert the pin in the lock mechanism so
that the grey color of the pin isn’t visible anymore.
3.3 Unlocking the height mechanism
In the factory, the height-positioning system in the display stand is locked with a red pin
to prevent damage during transportation. You’ll have to remove this pin before adjusting
your display height position.
10 K5902079 CORONIS UNITI 21/04/2015

3. Display installation
To remove the pin:
1. Position the display with its rear side facing you.
2. While holding the display panel pushed down, pull out the red pin in the display stand.
3. Keep the pin in the dedicated hole in case the display needs to be shipped later.
To retain the pin for possible future transportation, insert the short, red end of the pin
back into the stand of your display.
3.4 Adjusting the display position
In the factory, the height-positioning and the tilt system in the display stand are locked
with red pins to prevent damage during transportation. You’ll have to remove both pins
before adjusting your display position.
To adjust the display position
1. Remove the tilt lock pin, see "Unlocking the tilt mechanism", page 10.
2. Remove the height lock pin in the display stand, see "Unlocking the height mechanism", page 10.
3. Tilt, swivel, raise and lower the display as desired.
K5902079 CORONIS UNITI 21/04/2015 11

3. Display installation
CAUTION:Do not try to pivot your display when attached to the stand. Trying to do so
could cause serious damage to your display and its stand.
3.5 Connecting the signal cables
To get access to the connectors, remove the connector compartment cover. See "Re-
moving the connector compartment cover", page 9 .
To connect the signal cables to the display:
1. Connect one head of the display controller to the DisplayPort connector with one of the supplied Dis-
playPort cables.
12 K5902079 CORONIS UNITI 21/04/2015

3. Display installation
2. Connect another head of the display controller to the other DisplayPort connector with one of the sup-
plied DisplayPort cables.
3. Connect a PC USB downstream connector to the display’s USB upstream connector by means of the
supplied USB 2.0 cable.
K5902079 CORONIS UNITI 21/04/2015 13

3. Display installation
Communication with the display is possible via DisplayPort although it is recommended
to use the USB upstream connector for faster communication.
3.6 Connecting the power cable
To connect the power cable to the display:
1. Connect the supplied external DC power supply to the +24 VDC power input of your Coronis Uniti
display.
14 K5902079 CORONIS UNITI 21/04/2015

3. Display installation
Warning:Fasten the power connector to your display with the screws provided at the sides of the con-
nector.
2. Plug the other end of the external DC power supply into a grounded power outlet by means of the proper
power cord delivered in the packaging.
Use the external power supply delivered with your display. If you do not use the correct
power supply, the display will not start up.
3.7 Mounting the film clip
To mount the film clip
The film clip can be mounted on the top side of the display.
1. Position the film clip on the top side of the bezel at the desired location (in the middle, left or right).
K5902079 CORONIS UNITI 21/04/2015 15

3. Display installation
2. To remove the film clip, lift the front end or rear end of the clip.
3.8 Mounting the MultiTouchPad
To mount the MultiTouchPad
1. Connect the MultiTouchPad to one of the USB downstream connectors (using either those found in the
cable compartment or on the right side of the display).
2. With the MultiTouchPad attached and the driver installed, simply press on the MultiTouchPad to move
the focus on the SpotView around the display(s). The SpotView vanishes when no finger is pressing
on the MultiTouchPad, unless the left side of the MultiTouchPad button is held down.
16 K5902079 CORONIS UNITI 21/04/2015

3. Display installation
3.9 Routing the cables & Reattach the connector compartment
cover
To route the cables
1. Route all connected cables through the cable routing channel in the stand of your display.
Tip: The cable straps at the inside of the connector compartment allow you to fix the cables for better
shielding of the cables.
To reattach the connector compartment cover
1. Reattach the connector compartment cover by sliding the cover’s top. You’ll hear a “click” sound of the
cover’s clips when the connector compartment cover is in position.
K5902079 CORONIS UNITI 21/04/2015 17

3. Display installation
3.10 Fixation of the foot on the desk
Overview
If you would like to attach the Coronis Uniti to a desk, the tilt & swivel foot has 4 screw holes (4x M4) to
mount the foot on a desk.
18 K5902079 CORONIS UNITI 21/04/2015