Barco ADP361 User manual

ADP361
24” Auxiliary Display Panel
for Controller Working Positions

Today’s Air Traffic Controllers are using more and more tools
to display an ever-increasing load of information. That is
why more and more visualization capabilities with respect to
display size and resolution are needed. However, using
multiple displays with different sizes increases the risk for HMI
inconsistency. Barco’s 24” ADP361 auxiliary display series is
especially designed to meet these concerns.
The ADP361 series is perfectly suited to extend the high-
resolution surface of today’s 2Kx2K main display panels like
Barco’s ISIS or ISONA, while maintaining a good optical match
with the main display. Its flexibility allows both surface and
resolution to be extended with over 50% per added panel. The
ADP361 can be used beside a main display (portrait mode) as
well as on top of a main display (landscape mode) in order to
maximize the interactive surface available to a controller in a
limited console space.
Increasing visualization capability
for controller working positions
Main features
• 24” AMLCD matching the height of 2048 x 2048 main display
• Sleek bezel design
• 1200 x 1920 WXGA, 2.3 MP resolution
• Optically stabilized brightness (up to 250 cd/m2, 73 fL)
• High contrast: 450:1
• High dimming ratio > 50:1
• Long lifetime backlight: > 40,000 hours to 50% brightness
• Continuous Automatic Phase Adjustment (APA)
• Low noise and low heat design
• Selectable color temperatures to match main display in CWP
• Multiple inputs for flexible control

2
Broad connectivity
Meeting ATC requirements
While commercial displays are designed for an office environment, the ADP361 has been developed especially to work well
with 2048 x 2048 main displays with a 24 x 7 service requirement:
• Wider brightness control range keeping perfect color balance under all settings, including dark contrast room conditions
• Stabilized and calibrated light output for consistent image reproduction within one position and among multiple positions
• Reliable selectable white point settings to match with any well aligned main display
• Built-in hardware image rotator for more graphic board performance
• Multiple inputs for e.g. main and fall-back sources
• Analog and digital inputs
• Low noise and low heat design for operator convenience
• Long term support by leading ATC supplier Barco
Superior image quality
Low life cycle cost
The ADP361 relies on Barco’s near-zero maintenance concept,
which encompasses an easy set-up, internal stabilization and
calibration and several Built-In Test (BIT) patterns for easy
diagnostics. In addition, Barco’s optional CHECKUP! configuration
and maintenance software continuously checks the registered
ADP361 displays for their online status and warns system
administrators for preventive maintenance actions.
Last but not least, Barco’s worldwide PRO.CARE support
service assures long-term support and operational service for
the ADP361.
The ADP361 features Barco’s unique APA (Automatic Phase
Adjust) function, which guarantees artifact-free images over
time.
At startup After time without APA After time with APA
1. Optional control port (ISIS alike)
2. USB (master) connection
3. USB (slave) connection
4. Ethernet connection
5. Serial control connection
6. DC power input
7. DVI-I analog & digital video input
• DVI-D (DDC compatible)
8. DB15 analog video input
• DDC compatible
1
8
7
6
5
4
3
The ADP361 is equipped
with built-in automatic color
calibration circuitry. With the
optional color sensor, the ADP361
display can be automatically
calibrated, so it is perfectly
color matched with the aside
installed main or auxiliary displays.
In combination with a large
dimming range, very high
panel contrast and excellent
color tracked control range, a
consistent large HMI surface is
guaranteed between displays,
between CWPs and over time. This
brings additional operator comfort,
no ambiguous image interpreation
and near zero maintenance.
Perfect color matching

Barco
Pres. Kennedypark 35 - B-8500 Kortrijk, Belgium
Phone: [phone] - Fax: [phone]
E-mail: sales.airtraffi[e-mail]
Barco Orthogon AG
Hastedter Osterdeich 222 - 28207 Bremen, Germany
Phone: [phone] - Fax: [phone]
BarcoView, LLC
3059 Premiere Parkway - Duluth, Georgia, 30097-4905, USA
Phone: [phone] - Fax: [phone]
E-mail: [e-mail]
Contact one of the above for your local sales office
6
Si gma
In search of continuous improvement
Ref. T-P-ADP-1005
Technical specifications are subject to change without prior notice
www.BarcoAirTraffic.com
Technical specifications
Electro optical
Panel type: Active Matrix LCD (Silicon TFT)
Panel diagonal: 24 inch / 61 cm
Image dimensions: 518 x 324 mm / 20.4 x 12.76 inch
Pixel dimensions: 0.27 x 0.27 mm
Panel resolution: 1200 x 1920 pixels (WXGA)
(portrait)
Screen specifications: 16 million colors
256 grayscales per color
Light output: stabilized up to 250 cd/m2
73 fL (at 10o to 30oC ambient)
Dimming ratio > 50:1
Panel contrast ratio: typ. 450 :1
Color temperature: White point selectable between 6000 K
and 10,000 K to match main displays
Automatic color calibration: Via optional external calibration tool
Calibration tool (USB) + software
required
Viewing angle: Horizontal and vertical: > +/- 80o
(CR = 10)
Interfaces
3 selectable video inputs: One DVI – two analog inputs
(Automatic upscaling for typical lower
resolutions)
Auto-sync: Separate H&V/ Ext Combined /
Sync on Green
Connector type: DB9 for RS232 link
USB for optional tools/functions
(e.g. separate control box for
brightness / contrast /calibration tool)
Mini Din for control purposes
Ethernet RJ45 for maintenance
& control purposes
Controls
On bezel: standard 5 control keys: up, down,
enter, exit, stand-by
OSD: Menu Driven On-Screen Display
Remote control: RS232 link (Barco Protocol) /
Barco Keypad / USB control
Power
Power supply: External power supply box
Input: 100 - 240 VAC - 2.5 A
Frequency limits: 45-65Hz
Power consumption: typical 80 W (max. 130W)
General Data
Bezel: Sleek design for multiple display mounting
Weight: 8 kg / 17 lbs
MTTR: less than 0.5 hrs
Environmental
Temperature
Operating: 0oC/+35oC (+32oF/+95oF)
Storage: -20oC/+60oC (-4oF/+140oF)
Humidity 85% max (non-condensing)@35oC (95oF)
Altitude (pressure)
Operating: 15,000 ft (57.16 kPa)
Storage: 35,000 ft (23.84 kPa)
EMC
Emission FCC class A vol. II part 15 subpart J
Immunity EN50082-2, EN55022 limit A
Approvals
IEC 950, UL 1950, c-UL 950, CE 2001
Part number
K9334203
Options
• Remote control for brightness and contrast (USB) with 2 rotary digitizers
• USB based color sensor for color calibrations
• VESA arm / foot
• Contact factory for more details
324 mm (Active area)
366 mm
564 mm
518,4 mm (Active area)
67 mm 330 mm
529,4 mm
The ADP361 fits most
commercial VESA arms.