Barco MDCC-4430 User manual

ENABLING BRIGHT OUTCOMES
MDCC-4430 (NC)
MDCC-6530 (NC)
User guide
Coronis Fusion 4MP / 6MP

Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com

3R5911227 /05 Coronis Fusion 4MP / 6MP
1 Welcome!.......................................................................................................................................................................................................... 5
1.1 What's in the box................................................................................................................................................................................6
1.2 At a glance.............................................................................................................................................................................................6
2 Installation ....................................................................................................................................................................................................... 9
2.1 Display controller installation....................................................................................................................................................10
2.2 Display position adjustment ......................................................................................................................................................10
2.3 Cable connections.......................................................................................................................................................................... 11
2.4 MXRT driver and Intuitive Workflow Tools installation ...............................................................................................12
2.5 QAWeb registration .......................................................................................................................................................................13
2.6 VESA-mount installation.............................................................................................................................................................13
3 Daily operation .........................................................................................................................................................................................17
3.1 Recommendations for daily operation ................................................................................................................................18
3.2 Shortcut bar........................................................................................................................................................................................18
3.3 Standby switching...........................................................................................................................................................................19
3.4 SoftGlow light mode switching ................................................................................................................................................19
3.5 OSD menu access and use ......................................................................................................................................................20
4 Advanced operation............................................................................................................................................................................21
4.1 OSD menu language ....................................................................................................................................................................22
4.2 OSD menu orientation..................................................................................................................................................................22
4.3 OSD menu automatic close function....................................................................................................................................22
4.4 Power lock function........................................................................................................................................................................22
4.5 SoftGlow Task light.........................................................................................................................................................................23
4.6 SoftGlow Wall light .........................................................................................................................................................................23
4.7 DPMS mode.......................................................................................................................................................................................24
4.8 Hibernate ............................................................................................................................................................................................. 24
4.9 Luminance target ............................................................................................................................................................................25
4.10 Color presets .....................................................................................................................................................................................25
4.10.1 Color temperature.......................................................................................................................................................25
4.10.2 Color coordinates........................................................................................................................................................26
4.11 Color space ........................................................................................................................................................................................26
4.12 Viewing modes.................................................................................................................................................................................26
4.13 Display functions .............................................................................................................................................................................27
4.14 sRGB .....................................................................................................................................................................................................27
Table of contents

R5911227 /05 Coronis Fusion 4MP / 6MP4
4.15 Ambient Light Compensation (ALC).....................................................................................................................................28
4.16 Reading rooms.................................................................................................................................................................................28
4.17 Continuous Ambient Light Compensation (ALC)..........................................................................................................29
4.18 Embedded QA ..................................................................................................................................................................................29
4.18.1 About Embedded QA................................................................................................................................................29
4.18.2 DICOM status report .................................................................................................................................................29
4.18.3 DICOM compliance check .....................................................................................................................................30
4.18.4 DICOM calibration ......................................................................................................................................................30
4.18.5 Reset DICOM calibration........................................................................................................................................31
4.18.6 DICOM error threshold.............................................................................................................................................31
4.19 Image scaling....................................................................................................................................................................................31
4.20 Image source selection................................................................................................................................................................31
4.21 Grayscale conversion modes...................................................................................................................................................32
4.22 DisplayPort standard version ...................................................................................................................................................32
4.23 EDID timings......................................................................................................................................................................................33
4.24 Display info.........................................................................................................................................................................................33
4.25 Display status....................................................................................................................................................................................33
4.26 SteadyColor™ ..................................................................................................................................................................................34
4.27 Maximum luminance demo .......................................................................................................................................................34
5 Cleaning your display........................................................................................................................................................................35
5.1 Cleaning instructions.....................................................................................................................................................................36
6 Repackaging instructions ..............................................................................................................................................................37
6.1 Repackaging instructions...........................................................................................................................................................38
7 Important information.........................................................................................................................................................................43
7.1 Safety information...........................................................................................................................................................................44
7.2 Cybersecurity ....................................................................................................................................................................................45
7.3 Environmental information.........................................................................................................................................................45
7.4 Regulatory compliance information......................................................................................................................................47
7.5 EMC notice .........................................................................................................................................................................................49
7.6 Explanation of symbols................................................................................................................................................................51
7.7 Legal disclaimer...............................................................................................................................................................................55
7.8 Open source license information ...........................................................................................................................................55
7.9 Technical specifications...............................................................................................................................................................56

5R5911227 /05 Coronis Fusion 4MP / 6MP
Welcome! 1

R5911227 /05 Coronis Fusion 4MP / 6MP6
1.1 What's in the box
Overview
• Coronis Fusion 4MP / 6MP display
• Printed user guide
• Documentation disc, containing different languages of this user guide and the Barco “Display Controller
and Intuitive Workflow Tools” user guide
• System sheet
• Cables for Mains, Video and USB
If you ordered a Barco MXRT display controller, it is also in the box together with its accessories. A dedicated
user guide is available on the documentation disc.
Keep your original packaging. It is designed for this display and is the ideal protection during
transport and storage.
The user guides are also available on www.barco.com/support
1.2 At a glance
Product overview
7
7 8 8
11 2
3
109
5
6
4
Image 1–1
1. SoftGlow Wall light
2. Ambient light sensor and Power status LED
- Off: Display not powered (mains cable unplugged or power switch in OFF position), or display is in
normal operation
- Fast blinking amber: Display is entering DPMS mode
- Slow blinking amber: Display is in DPMS mode
- Steady amber: Display manually switched off via the jog dial, or display in hibernate mode (requires
DPMS and Hibernate to be enabled in the OSD menu)
3. Front sensor
Welcome!

7R5911227 /05 Coronis Fusion 4MP / 6MP
4. VESA mount cover
5. USB-A 2.0 downstream connector with high-power charging functionality
6. Connector compartment cover
7. SoftGlow Task light
8. Jog dial
9. Cable routing channels
10.Stand locking mechanism
Connectors
1 2 3 4 6 7 85
Image 1–2
1. Kensington security slot
2. Service port (for Barco service purposes only)
3. DisplayPort IN 2
4. DisplayPort OUT (covered with a plastic cap by default, remove the cap to use this connector)
5. DisplayPort IN 1
6. USB-A 2.0 downstream connectors (2x)
7. USB-B 2.0 upstream connector
8. 100–240 VAC mains power input and power switch
Welcome!

R5911227 /05 Coronis Fusion 4MP / 6MP8
Welcome!

9R5911227 /05 Coronis Fusion 4MP / 6MP
Installation 2

R5911227 /05 Coronis Fusion 4MP / 6MP10
2.1 Display controller installation
About
Before you install your display and connect it with the workstation, make sure to have a suitable1display
controller installed in the workstation.
The Coronis Fusion 4MP / 6MP display operates at its full specifications when driven by a Barco
MXRT display controller and MXRT driver (which also includes the Barco Intuitive Workflow
Tools). If you ordered a MXRT display controller, it is included in the box of your display.
For more information and installation instructions, please check the Barco “Display Controller and
Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.com/
support.
2.2 Display position adjustment
To adjust the display position
After unpacking, you can safely tilt and swivel the display to your preferred position.
Image 2–1
To adjust the height of the display, first move the slider at the back of the stand to the unlock position. Then
you can raise or lower the display as desired.
Installation
1. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support
> Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)

11R5911227 /05 Coronis Fusion 4MP / 6MP
Image 2–2 Image 2–3
WARNING: The height can be locked only when the display is in the lowest position, even though
the slider at the back of the stand can be moved to the lock position at any height of the display.
2.3 Cable connections
To connect the cables
1. Open the connector compartment. Do this by gently lifting the bottom of the connector compartment cover,
after which it can be removed from the display.
Image 2–4
2. Connect the video source(s) from your workstation(s) to the DisplayPort IN connector(s) of the display.
Important: Do not connect any video source(s) to the DisplayPort OUT connector. Do not confuse this
connector with the DisplayPort IN 1 and 2 connectors.
Installation

R5911227 /05 Coronis Fusion 4MP / 6MP12
Note: The MDCC-4430, MDCC-6530 can have multiple video inputs connected at once, and switching
between these inputs can be easily done in the OSD menu. See “Image source selection”, page 31 for
more info on how to configure the different video inputs on your display.
3. The DisplayPort OUT allows you to daisy chain your display and an external display using DisplayPort
Multi-Stream Transport (MST).
Note: By default, the DisplayPort OUT is covered with a plastic cap which has to be removed before you
can use this connector.
4. Connect the workstation's USB host to the USB upstream connector on the display if you want to make
use of QAWeb or any of the display USB downstream connectors (e.g. to connect a keyboard, mouse,
touchpad or another peripheral).
Note: When cables or other objects are left on a touchpad, these can be misinterpreted as fingers and may
block DPMS activation. Barco recommends to always keep the touchpad clear of other objects.
5. Connect the supplied mains cable to the power input on the display.
2
3 4
4
2
5
DP IN 2
SERVICE
DP OUT DP IN 1
USB DOWN
USB UP
AC IN
Image 2–5
6. Route all cables through the cable duct in the stand of your display. For better strain-relief and shielding of
the cables, use the cable clips at the inside of the connector compartment.
7. Close the connector compartment. Slide the top of the connector compartment cover into position and then
push the bottom of the cover.
Note: Make sure that the power switch (next to the power input) is the desired position before closing the
connector compartment.
8. Connect the supplied mains cable to a grounded power outlet.
2.4 MXRT driver and Intuitive Workflow Tools
installation
About
When you are using a Barco MXRT display controller, you can start up your Coronis Fusion 4MP / 6MP
display system and install the MXRT driver and Intuitive Workflow Tools . Barco’s Intuitive Workflow Tools
are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate
workflow.
To install the MXRT driver and Intuitive Workflow Tools
1. Switch on your Coronis Fusion 4MP / 6MP as described in “Standby switching”, page 19.
2. Turn on the workstation connected to your display.
Your display will be running in a basic video mode at a default refresh rate when first time starting up.
3. Download the latest MXRT driver and Intuitive Workflow Tools from www.barco.com/mxrt.
Installation

13R5911227 /05 Coronis Fusion 4MP / 6MP
4. Install the MXRT driver and Barco’s Intuitive Workflow Tools as described in the Barco “Display
Controller and Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.
com/support.
5. When the drivers are completely installed, your display will automatically detect the connected video input
signal(s) and apply the correct video mode and refresh rate.
2.5 QAWeb registration
About
QAWeb Enterprise helps you manage quality and assure compliance of your expanding healthcare
enterprise with less effort, lower cost, and complete confidence. This fully automated and secure system
guarantees a consistent image quality and uptime for all registered imaging display systems within your facility
and across your enterprise. Learn more at www.barco.com/qaweb.
To register your display system to your QAWeb Enterprise organization, the QAWeb Enterprise Agent must be
installed and running on your workstation and it must be able to communicate with the QAWeb Enterprise
cloud service.
For more information and instructions, check the QAWeb Enterprise user guide on www.barco.com/support/
qaweb-enterprise.
When still using the older MediCal QAWeb, visit www.barco.com/support/medical-qaweb to obtain
the installation package and user documentation.
2.6 VESA-mount installation
CAUTION: Use suitable mounting apparatus to avoid risk of injury.
WARNING: Never move a display attached to an arm by pulling or pushing the display itself.
Instead, make sure that the arm is equipped with a VESA compliant handle and use this to move
the display.
Please refer to the instruction manual of the arm for more information and instructions.
WARNING: Use a mount that is compliant with the VESA 100 mm standard.
Use a mount that can support the weight of the display. Refer to the technical specifications of this
display for the applicable weight.
Overview
The panel, standard attached to a stand, is compatible with the VESA 100 mm standard. Thus, it can be used
with an arm that is approved by VESA. This chapter shows you how to release the panel from the stand and
how to attach it to an arm. If you’re not using an arm, you can skip this chapter.
1. Unlock the stand locking mechanism and put the display in the highest position.
Installation

R5911227 /05 Coronis Fusion 4MP / 6MP14
Image 2–6
2. Put the display face down on a clean and soft horizontal surface. Be careful not to damage the panel
screen.
3. Push the VESA mount cover to the right and lift the cover on the right with your finger or a flathead
screwdriver.
Image 2–7
4. Push the VESA mount cover to the left and release the cover on the left with a flathead screwdriver.
Image 2–8
5. Rotate the VESA mount cover to uncover the screws fixing the panel to the stand.
Installation

15R5911227 /05 Coronis Fusion 4MP / 6MP
Image 2–9
6. Unscrew the 4 fixation screws while supporting the stand.
Image 2–10
7. Attach the panel firmly to the arm using 4 M4 screws.
Respect the following rule to select an appropriate screw length:
- Lmin = T + W + 6.5 mm
- Lmax = T + W + 10 mm
T
W
Lmin
Lmax
Image 2–11
Installation

R5911227 /05 Coronis Fusion 4MP / 6MP16
Installation

17R5911227 /05 Coronis Fusion 4MP / 6MP
Daily operation 3

R5911227 /05 Coronis Fusion 4MP / 6MP18
3.1 Recommendations for daily operation
Optimize the lifetime of your display
Enabling the Display Power Management System (DPMS) of your display will optimize its diagnostic lifetime
by automatically switching off the backlight when the display is not used for a specified period of time. By
default, DPMS is enabled on your display, but it also needs to be activated on your workstation. To do this, go
to the “Power Options” of your workstation.
Barco recommends setting DPMS activation after 20 minutes of non-usage.
Use a screen saver to avoid image retention
Prolonged operation of an LCD with the same content on the same screen area may result in a form of image
retention.
You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver. You can
activate a screen saver in the “Display properties” window of your workstation.
Barco recommends setting screen saver activation after 5 minutes of non-usage. A good screen
saver displays moving content.
In case you are working with the same image or an application with static image elements for several hours
continuously (so that the screen saver is not activated), change the image content regularly to avoid image
retention of the static elements.
Understand pixel technology
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a
limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic
performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD
panels.
Enhance user comfort
Every Barco multi-head display system is color matched to the tightest specifications in the market.
Barco recommends keeping color-matched displays together. Furthermore, it is important to use all
displays of a multi-head configuration at the same rate to preserve color matching throughout the
economic lifetime of the system.
Maximize quality assurance
QAWeb Enterprise helps you manage quality and assure compliance of your expanding healthcare enterprise
with less effort, lower cost, and complete confidence. This fully automated and secure system guarantees a
consistent image quality and uptime for all registered PACS display systems within your facility and across
your enterprise.
Barco highly recommends to use QAWeb Enterprise. Learn more at www.barco.com/qaweb.
3.2 Shortcut bar
About the shortcut bar
The shortcut bar gives direct access to a number of OSD menu functions without having to browse the OSD
menu:
•“Standby switching”, page 19
•“SoftGlow light mode switching”, page 19
Daily operation

19R5911227 /05 Coronis Fusion 4MP / 6MP
•“OSD menu access and use”, page 20
Image 3–1
To activate a shortcut bar function
1. During normal operation, press or turn the jog dial. The shortcut bar is activated.
2. Turn the jog dial left or right to select a function.
3. Press the jog dial to confirm your selection and to activate the function.
3.3 Standby switching
To switch on your display
Press the jog dial to activate your display.
Make sure that the power switch next to the mains power input connector is in position “I” when
switching on your display.
To switch off your display
1. Press or turn the jog dial to activate the shortcut bar.
2. Turn the jog dial and select the standby icon ( ).
3. Press the jog dial to confirm your selection.
4. Press the jog dial again to switch off the display.
3.4 SoftGlow light mode switching
About the SoftGlow lights
The SoftGlow Task light sheds a light on the desktop, while the SoftGlow Wall light provides ambient lighting
for the reading room to reduce eye fatigue. The brightness of each is adjustable.
To switch the SoftGlow light mode
1. Press or turn the jog dial to activate the shortcut bar. The SoftGlow lights icon ( ) is selected by default
when the KVM switch is disabled.
2. If not selected by default, turn the jog dial and select the SoftGlow lights icon.
3. Press the jog dial repeatedly to cycle through the different SoftGlow light modes:
SoftGlow Task light ON → SoftGlow Wall light ON → SoftGlow Task + SoftGlow Wall light ON → SoftGlow
lights OFF→ ...
To adjust the brightness of the SoftGlow lights, please refer to “SoftGlow Task light”, page 23 and
“SoftGlow Wall light”, page 23.
The SoftGlow lights can also be enabled and configured in the Intuitive Workflow Tools. See the
Barco “Display Controller and Intuitive Workflow Tools” user guide on the included documentation
CD, or at www.barco.com/support.
Daily operation

R5911227 /05 Coronis Fusion 4MP / 6MP20
3.5 OSD menu access and use
About the OSD menu
The OSD menu allows you to configure different settings to make your Coronis Fusion 4MP / 6MP fit your
needs within your working environment. Also, you can retrieve general information about your display and its
current configuration settings through the OSD menu.
To access the OSD menu
1. Press or turn the jog dial to activate the shortcut bar.
2. Turn the jog dial and select the OSD menu icon ( ).
3. Press the jog dial to enter the OSD menu.
4. If the OSD menu locked message appears, turn and hold the jog dial right for 5 seconds, until the OSD
menu unlocked message appears.
To navigate through the OSD menus
• Turn the jog dial left or right to scroll through the (sub)menus, to change values or to make selections.
• Press the jog dial to go into a submenu or confirm adjustments and selections.
• Press and hold the jog dial for approximately 3 seconds to cancel adjustments.
• Turn the jog dial left on a first (sub)menu item to exit the (sub)menu.
Daily operation