Barco F80 series User manual

ENABLING BRIGHT OUTCOMES
User Manual
F80

Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco Fredrikstad AS
Habornveien 53, N-1630 Gamle Fredrikstad, Norway
[email protected]
www.barco.com
Product revision
Software Revision: 2.1

Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Changes
Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made
to the information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the
secured Barco web site https://www.barco.com/en/signin.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brand and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or their manufacturers.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of
any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on
the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of
complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate
period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the
purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for
direct or indirect damage, and also damage attributed to the operation of software as well as to other services
provided by Barco, being a component of the system or independent service, will be deemed invalid provided
the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the
intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the
goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of
risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the
purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are
attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear
as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual
must be complied with by the customer.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area may cause harmful interference, in which case the user will be responsible for correcting any interference
at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment

FCC responsible: Barco Inc.
3059 Premiere Parkway Suite 400
30097 Duluth GA, United States
Tel: [phone]
Patent protection
Please refer to www.barco.com/about-barco/legal/patents
EMC statements
EN55032/CISPR32 Class A MME (MultiMedia Equipment)
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment
may cause radio interference.
Class A ITE (Information Technology Equipment)
Warning : This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
警告使用者:此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會
被要求採取某些適當的對策。
Disclaimer for camera usage
Barco provides a kit with a laser range finder and USB camera to help measure the distance from the front of
the projector to the projected surface and to help monitor the performance of the projector. Barco disclaims
any liability for any use of the USB camera outside this intended use.
Disclaimer for network usage
Barco highly recommends to install the projector in a closed network environment to minimize the risk of
leaking, hacking or corrupting of company confidential information; commercial sensitive information and/or
personal data. Furthermore, strengthen your network security to protect the projector against unauthorized
access by third parties. To the maximum extent permitted by law, Barco disclaims any liability for the use of the
projector in an open network environment.

5R5906852 /06 F80
1 Safety................................................................................................................................................................................................................... 9
1.1 General considerations ...............................................................................................................................................................10
1.2 Important safety instructions..................................................................................................................................................... 11
1.3 Product safety labels.....................................................................................................................................................................14
1.4 Risk Group 3 Safety ......................................................................................................................................................................16
1.4.1 General considerations............................................................................................................................................16
1.4.2 High Brightness precautions: Hazard Distance (HD) .............................................................................17
1.4.3 HD for fully enclosed projection systems.......................................................................................................19
1.4.4 HD in function of the lens Throw Ratio (TR) ................................................................................................20
2 Remote Control Unit...........................................................................................................................................................................21
2.1 Remote control, battery installation ......................................................................................................................................22
2.2 Using the mini-jack connector of the RCU........................................................................................................................23
2.3 Remote control, on/off button...................................................................................................................................................23
3 Input & Communication...................................................................................................................................................................25
3.1 Introduction.........................................................................................................................................................................................26
3.2 Connection Panel ...........................................................................................................................................................................26
3.3 Making connections.......................................................................................................................................................................27
3.4 Connector specifications ............................................................................................................................................................27
3.4.1 DVI-I ...................................................................................................................................................................................27
3.4.2 Display Port 1.2............................................................................................................................................................28
3.4.3 HDMI 2.0..........................................................................................................................................................................28
3.4.4 SDI.......................................................................................................................................................................................29
3.4.5 HDBase T........................................................................................................................................................................29
3.4.6 High-bandwidth Digital Content Protection (HDCP)................................................................................30
3.5 Control interfaces............................................................................................................................................................................30
3.5.1 RS-232..............................................................................................................................................................................30
3.5.2 LAN/Ethernet.................................................................................................................................................................31
3.5.3 USB-A port......................................................................................................................................................................31
3.5.4 DMX....................................................................................................................................................................................31
3.6 LED and Button indication chart.............................................................................................................................................31
4 Getting Started.........................................................................................................................................................................................33
4.1 Local Keypad and LCD panel ..................................................................................................................................................34
4.2 Power modes ....................................................................................................................................................................................34
4.3 Power mode transitions...............................................................................................................................................................35
Table of contents

R5906852 /06 F806
4.3.1 General.............................................................................................................................................................................35
4.3.2 Power on projector .....................................................................................................................................................35
4.3.3 Going from READY to ON......................................................................................................................................36
4.3.4 Going from ON to READY......................................................................................................................................36
4.3.5 Going from READY to ECO standby................................................................................................................36
4.3.6 Going from ECO to ON ............................................................................................................................................36
4.3.7 Wake on LAN (WOL) ................................................................................................................................................36
4.4 Status overview................................................................................................................................................................................37
4.5 Power off projector ......................................................................................................................................................................... 37
4.6 Increasing the projector life time ............................................................................................................................................38
4.7 Operation in 24/7 Mode...............................................................................................................................................................38
4.8 Using the RCU..................................................................................................................................................................................38
4.9 Projector Address ...........................................................................................................................................................................40
4.9.1 Controlling the projector ..........................................................................................................................................40
4.10 Quick setup via Direct access..................................................................................................................................................41
5 GUI –Introduction.................................................................................................................................................................................43
5.1 Overview..............................................................................................................................................................................................44
5.2 Navigation ...........................................................................................................................................................................................45
5.3 Test Patterns......................................................................................................................................................................................47
6 GUI –Source .............................................................................................................................................................................................49
6.1 Displaying a single source .........................................................................................................................................................50
6.2 Displaying multiple sources: Stitched layouts.................................................................................................................50
6.3 Connector Settings ........................................................................................................................................................................51
7 GUI –Image................................................................................................................................................................................................55
7.1 Setting image levels manually.................................................................................................................................................56
7.2 Adjusting the sharpness..............................................................................................................................................................57
7.3 Adjusting the gamma correction.............................................................................................................................................58
7.4 Setting the desired Gamma type............................................................................................................................................59
7.5 Digital Shift & Zoom.......................................................................................................................................................................61
7.6 RealColor P7 .....................................................................................................................................................................................65
7.7 Setting the output resolution.....................................................................................................................................................67
7.8 BrilliantColorTM .................................................................................................................................................................................68
7.9 Displaying HDR content..............................................................................................................................................................69
8 GUI –Installation....................................................................................................................................................................................71
8.1 Configuring the lens, optical zoom-focus ..........................................................................................................................72
8.2 Configuring the lens, shift...........................................................................................................................................................72
8.3 Configuring the lens, Shift to center .....................................................................................................................................73
8.4 Configuring the lens, tilt sensor...............................................................................................................................................74
8.5 Manipulating the rigging frame ...............................................................................................................................................74
8.6 Manipulating the rigging frame, center position.............................................................................................................76
8.7 Orientation ..........................................................................................................................................................................................77
8.8 Scaling modes .................................................................................................................................................................................. 77
8.9 Warping ................................................................................................................................................................................................79
8.9.1 Warping –On/Off.........................................................................................................................................................79
8.9.2 Warping –Screen Size.............................................................................................................................................80
8.9.3 Warping –4 corners adjustment.........................................................................................................................82
8.9.4 Warping –Bow..............................................................................................................................................................83
8.9.5 Warping –Warp files .................................................................................................................................................88
8.9.6 Warping –Latency control in a multi projector setup ..............................................................................89
8.10 Blending & masking.......................................................................................................................................................................91

7R5906852 /06 F80
8.10.1 Basic blend .....................................................................................................................................................................91
8.10.2 Blend & Blend mask ..................................................................................................................................................93
8.10.3 Blend Files ......................................................................................................................................................................95
8.10.4 Basic black level adjustment ................................................................................................................................96
8.10.5 RGB gain adjustment................................................................................................................................................98
8.10.6 Black Level Files..........................................................................................................................................................99
8.11 Illumination ...................................................................................................................................................................................... 100
8.12 3D projection .................................................................................................................................................................................. 101
8.12.1 Active Stereo & Passive Stereo....................................................................................................................... 101
8.12.2 Setup process 3D projection ............................................................................................................................. 102
8.12.3 Connection possibilities........................................................................................................................................ 102
8.12.4 3D Setup ....................................................................................................................................................................... 103
9 GUI –Macro’s and projector profiles .............................................................................................................................. 105
9.1 Saving the current projector settings in a profile ........................................................................................................ 106
9.2 Assigning a created projector profile to a preset........................................................................................................ 108
9.3 Deleting a projector profile...................................................................................................................................................... 109
10 GUI –System Settings .................................................................................................................................................................. 111
10.1 Communication..............................................................................................................................................................................112
10.1.1 Introduction to a Network connection ............................................................................................................112
10.1.2 Wired IP address set up ........................................................................................................................................112
10.2 IR control............................................................................................................................................................................................114
10.2.1 Broadcast address ...................................................................................................................................................114
10.2.2 Projector address......................................................................................................................................................115
10.2.3 IR sensors .....................................................................................................................................................................116
10.3 Setting a custom projector name .........................................................................................................................................117
10.4 DMX......................................................................................................................................................................................................118
10.5 Changing the User Interface language.............................................................................................................................119
10.6 Themes.............................................................................................................................................................................................. 120
10.7 Setting the measurement system ....................................................................................................................................... 120
10.8 ECO mode ....................................................................................................................................................................................... 121
10.9 Power settings ............................................................................................................................................................................... 121
10.10 Lens features.................................................................................................................................................................................. 122
10.11 Controlling the backlight of the LCD Display ................................................................................................................ 123
10.12 Factory reset................................................................................................................................................................................... 124
10.13 Lens Calibration............................................................................................................................................................................ 126
10.14 Operational mode ........................................................................................................................................................................ 128
10.15 Advanced Settings ...................................................................................................................................................................... 129
10.15.1 Remote access –Enable source preview .................................................................................................. 129
10.15.2 Remote access –Enable camera preview................................................................................................. 130
10.15.3 Service –Color Wheel........................................................................................................................................... 131
10.15.4 Advanced Settings –Color ................................................................................................................................. 132
10.15.5 Advanced Settings –Statistics ......................................................................................................................... 133
10.15.6 Advanced Settings –Pixel Shift ....................................................................................................................... 134
10.15.7 Checking the status of the Laser Banks...................................................................................................... 135
10.15.8 Advanced settings –Tilt sensor calibration ............................................................................................... 137
11 GUI –Status menu........................................................................................................................................................................... 139
11.1 Status menu overview............................................................................................................................................................... 140
12 Maintenance........................................................................................................................................................................................... 143
12.1 Cleaning the lens ......................................................................................................................................................................... 144
12.2 Cleaning the exterior of the projector................................................................................................................................ 144

R5906852 /06 F808
12.3 Filters .................................................................................................................................................................................................. 144
A Specifications........................................................................................................................................................................................ 145
A.1 Specifications of the F80-Q7 ................................................................................................................................................. 146
A.2 Specifications of the F80-Q9 ................................................................................................................................................. 147
A.3 Specifications of the F80-Q12 .............................................................................................................................................. 149
A.4 Specifications of the F80-4K7............................................................................................................................................... 150
A.5 Specifications of the F80-4K9............................................................................................................................................... 152
A.6 Specifications of the F80-4K12 ............................................................................................................................................ 153
A.7 Dimensions of a F80 ................................................................................................................................................................. 155
A.8 Technical Regulations ............................................................................................................................................................... 156
B Environmental information........................................................................................................................................................ 157
B.1 Disposal information................................................................................................................................................................... 158
B.2 China RoHS compliance.......................................................................................................................................................... 158
B.3 Taiwan RoHS compliance ....................................................................................................................................................... 160
B.4 Turkey RoHS compliance........................................................................................................................................................ 161
B.5 Production address..................................................................................................................................................................... 161
B.6 Contact information..................................................................................................................................................................... 161
B.7 Product Info (Taiwan)................................................................................................................................................................. 162
B.8 Download Product Manual ..................................................................................................................................................... 162
C Overview video timings for video interfaces............................................................................................................ 163
C.1 Overview video timings............................................................................................................................................................. 164
C.2 Overview video timings SDI Inputs .................................................................................................................................... 165
C.3 Overview video timings HDMI 2.0 inputs........................................................................................................................ 166
C.4 Overview video timings DisplayPort 1.2 inputs ........................................................................................................... 167
C.5 Overview video timings HDBaseT input.......................................................................................................................... 169
C.6 Overview video timings DVI Inputs .................................................................................................................................... 170
D DMX chart................................................................................................................................................................................................. 173
D.1 DMX chart, Basic ......................................................................................................................................................................... 174
D.2 DMX chart, Extended................................................................................................................................................................. 174

9R5906852 /06 F80
1.1 General considerations .................................................................................................................10
1.2 Important safety instructions.......................................................................................................... 11
1.3 Product safety labels.....................................................................................................................14
1.4 Risk Group 3 Safety......................................................................................................................16
About this document
Read this document attentively. It contains important information to prevent personal injury while installing and
using the F80 projector. Furthermore, it includes several cautions to prevent damage to the F80 projector.
Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this
chapter before installing the F80 projector.
Clarification of the term “F80”used in this document
When referring in this document to the term “F80”means that the content is applicable for following Barco
products:
•F80-Q7, F80-Q9, F80-Q12, F80-4K7, F80-4K9, F80-4K12
Model certification name
•GPC
Safety 1

R5906852 /06 F8010
1.1 General considerations
General safety instructions
•Before operating this equipment please read this manual thoroughly and retain it for future reference.
•Installation and preliminary adjustments should be performed by qualified Barco personnel or by
authorized Barco service dealers.
•All warnings on the projector and in the documentation manuals should be adhered to.
•All instructions for operating and use of this equipment must be followed precisely.
•All local installation codes should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,
as basis for National safety regulation world wide. The safety standard covers information technology
equipment including electrical business equipment intended to operate in “normal”environments (offices and
homes). This safety standard imposes important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy
hazard and having access to live parts. Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection
against the risk of fire. Simulated single fault condition testing reduce the risk of hazards and contribute to
ensure the safety of the equipment to the user even when the equipment’s normal operation fails.
Notice on optical radiation
This projector embeds extremely high brightness (radiance) lasers; this laser light is processed through the
projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting
the projection lens has been diffused within the optical path, representing a larger source and lower radiance
value than native laser light. Nevertheless the projected light represents a significant risk for the human eye
when exposed directly within the beam. This risk is not specific related to the characteristics of laser light but
solely to the high thermal induced energy of the light source; which is equivalent with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance (HD). The HD is defined from
the projection lens surface towards the position of the projected beam where the irradiance equals the
maximum permissible exposure as described in the chapter “Hazard Distance”.
Notice on optical radiation (addendum)
•F80-Q12, F80-4K12:
- The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector
conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR
1040, except with respect to those characteristics authorized by Variance Number 2017-V-4837
effective September 13, 2017 Do not stare into Beam.
- This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk
Group 3 (RG3) when an interchangeable lens with throw ratio greater than 2.2 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are
intended for professional use only, and are not intended for consumer use. Safety considerations for
RG3 projectors are discussed in section “Risk Group 3 Safety”, page 16.
- This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very
dangerous and should never be attempted.
•F80-Q9, F80-4K9:
- The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector
conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR
1040, except with respect to those characteristics authorized by Variance Number 2017-V-4837
effective September 13, 2017 Do not stare into Beam.
- This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk
Group 3 (RG3) when an interchangeable lens with throw ratio greater than 2.8 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are
intended for professional use only, and are not intended for consumer use. Safety considerations for
RG3 projectors are discussed in section “Risk Group 3 Safety”, page 16.
- This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very
dangerous and should never be attempted.
Safety

11R5906852 /06 F80
•F80-Q7, F80-4K7:
- The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector
conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR
1040, except with respect to those characteristics authorized by Variance Number 2017-V-4837
effective September 13, 2017 Do not stare into Beam.
- This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk
Group 3 (RG3) when an interchangeable lens with throw ratio greater than 3.5 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are
intended for professional use only, and are not intended for consumer use. Safety considerations for
RG3 projectors are discussed in section “Risk Group 3 Safety”, page 16.
- This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very
dangerous and should never be attempted.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having
appropriate technical training and experience necessary to be knowledgeable of potential hazards to which
they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY
and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk
to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks,
are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers
to any person other than SERVICE PERSONNEL. When installing an interchangeable lens with a throw ratio
that make the projector become RG3, refer to chapter “Risk Group 3 Safety”, page 16. Such combination of
projector and lens are intended for professional use only, and are not intended for consumer use.
FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED
PERSONNEL familiar with potential hazards associated with high intensity light beams.
1.2 Important safety instructions
To prevent the risk of electrical shock
•This product should be operated from a mono phase AC power source.
•This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the
supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-
type plug. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.
•Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•Use only the power cord supplied with your device. While appearing to be similar, other power cords have
not been safety tested at the factory and may not be used to power the device. For a replacement power
cord, contact your dealer.
•Do not operate the projector with a damaged cord. Replace the cord.
•Do not operate the projector if the projector has been dropped or damaged - until it has been examined
and approved for operation by qualified service personnel.
•Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should
be used. A cord rated for less amperage than the projector may overheat.
•Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electrical shock.
•Make sure that no objects enter into the vents and openings of the set.
•Do not expose this projector to rain or moisture.
•The projector is designed for indoor use only. Never operate the unit outdoors.
•Do not immerse or expose this projector in water or other liquids.
•Do not spill liquid of any kind on this projector.
•Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•Do not disassemble this projector, always take it to qualified service personnel when service or repair work
is required.
•Do not use an accessory attachment which is not recommended by the manufacturer.
Safety

R5906852 /06 F8012
•Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device
due to lightning and AC power-line surges.
To prevent personal injury
•To prevent injury and physical damage, always read this manual and all labels on the system before
powering the projector or adjusting the projector.
•To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the
projector. The projector weights about ±26 kg (±57 lbs) without lens and rigging frame.
•To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to
the eye.
•Warning: extremely high brightness projector: This projector embeds extremely high brightness
(radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not
accessible by the end user in any use case. The light exiting the projection lens has been diffused within
the optical path, representing a larger source and lower radiance value than native laser light.
Nevertheless the projected light represents a significant risk for the human eye when exposed directly
within the beam. This risk is not specific related to the characteristics of laser light but solely to the high
thermal induced energy of the light source; which is comparable with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance
(HD) is defined from the projection lens surface towards the position of the projected beam where the
irradiance equals the maximum permissible exposure as described in the chapter “High Brightness
precautions: Hazard Distance (HD)”, page 17.
•Based on international requirements, no person is allowed to enter the projected beam within the zone
between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by
creating sufficient separation height or by placing optional barriers. Within the restricted area operator
training is considered sufficient. The applicable separation heights are discussed in “High Brightness
precautions: Hazard Distance (HD)”, page 17.
•Don’t put your hand in front of the beam.
•This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics
inside the housing or compartments will violate any warranties and may be hazardous.
•A special device (“rigged frame”) based on an external frame must be used when the projector is deployed
in a hanging configuration, or when several projector must be stacked. See installation manuals for the
correct use of these devices.
•Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user.
•It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if
they have become visibly damaged to such an extent that their effectiveness is impaired. For example by
cracks or deep scratches.
•Cooling liquid circuit. The projector contains a cooling circuit filled with Green Ethylene glycol diluted
(53% Glycol –47% Demi water). When the cooling circuit leaks, switch off the device and contact qualified
service personnel. The liquid is not for household use. Keep out of reach of children. Harmful by oral
intake. Avoid exposure to pregnant women. Avoid contact with eyes, skin and clothing. Avoid inhale of the
noxious fumes.
•Never point or allow light to be directed on people or reflective objects within the HD zone.
•All operators shall have received adequate training and be aware of the potential hazards.
•In case of using an external cooling system position the hoses of the cooling system so that they will not be
tripped over, pulled, or contact hot surfaces.
To prevent fire hazard
•Do not place flammable or combustible materials near the projector!
•Barco projection products are designed and manufactured to meet the most stringent safety regulations.
This projector radiates heat on its external surfaces and from ventilation ducts during normal operation,
which is both normal and safe. Exposing flammable or combustible materials into close proximity of this
projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is
absolutely necessary to leave an “exclusion zone”around all external surfaces of the projector whereby no
flammable or combustible materials are present. The exclusion zone in the exhaust area must be not less
than 100 cm (40”). The exclusion zone on the intake area must be not less than 50 cm (20”).
•Do not place any object in the projection light path at close distance to the projection lens output. The
concentrated light at the projection lens output may result in damage, fire or burn injuries.
Safety

13R5906852 /06 F80
•Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable
and combustible materials away from the projector at all times. Mount the projector in a well ventilated area
away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In
the event of fire, use sand, CO2or dry powder fire extinguishers. Never use water on an electrical fire.
Always have service performed on this projector by authorized Barco service personnel. Always insist on
genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety
of this projector.
•Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can
represent a fire risk. After alignment the projector shall be securely mounted to the pedestal.
•Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the
projector and to protect it from overheating, these openings must not be blocked or covered. The openings
should never be blocked by placing the projector too close to walls, or other similar surface. This projector
should never be placed near or over a radiator or heat register. This projector should not be placed in a
built-in installation or enclosure unless proper ventilation is provided.
•Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent
hot exhaust air from projector and cooling system to the outside of the building.
•Let the projector cool completely before storing. Remove cord from the projector when storing.
To prevent projector damage
•Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due
to the high energy light emitted through the lens. Melting the lens cap may permanently damage the
surface of the projection lens.
•The air inlets of the projector must be cleaned on a regular basis. Cleaning the booth area would be
monthly-minimum. Neglecting this could result in disrupting the air flow inside the projector, causing
overheating. Overheating may lead to the projector shutting down during operation.
•The projector must always be installed in a manner which ensures free flow of air into its air inlets.
•If more than one projector is installed in a common projection booth, the exhaust air flow requirements are
valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in
decreased life expectancy of the projector as a whole as well as causing premature failure of the lasers.
•In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic
Compatibility (EMC) and safety requirements, it should always be operated with all of it's covers in place.
•Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. The device should not be placed in a built-in
installation or enclosure unless proper ventilation is provided.
•Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and
remove all power from the projector. Do not operate the projector again until it has been checked by
qualified service personnel.
•Do not block the projector cooling fans or free air movement around the projector.
•Do not use this equipment near water.
•Special care for Laser Beams: Special care should be used when DLP projectors are used in the same
room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely
damage the Digital Mirror DevicesTM in which case there is a loss of warranty.
•Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror
DevicesTM in which case there is a loss of warranty.
•Save the original shipping carton and packing material. They will come in handy if you ever have to ship
your equipment. For maximum protection, repack your set as it was originally packed at the factory.
•Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive
cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution.
•To ensure the highest optical performance and resolution, the projection lenses are specially treated with
an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry
cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual.
•Only connect the projector to signal sources and voltages as described in the technical specification.
Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of
the unit.
•Allowed ambient temperature range: ta= 10°C (50°F) to 40°C (104°F)
•Rated humidity = 20% RH to 80% RH Non-condensed.
Safety

R5906852 /06 F8014
•Do not operate the projector outside its temperature and humidity specifications as this may result in
overheating and malfunction.
On servicing
•Do not attempt to service this product yourself. This product contains no user serviceable parts except
parts describe in the User manual. Attempts to modify/replace mechanics or electronics inside the housing
or compartments will violate any warranties and may expose you to dangerous voltage potentials, risk of
electric shock and retinal eye injury.
•Refer all servicing to Barco authorized repair centers.
•Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
•Remove all power from the projector and refer servicing to Barco authorized repair center under the
following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
•Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
•Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via [email protected].
1.3 Product safety labels
Light beam related safety labels
Label image Label description Label location
Refer to user manual for further information!
Caution! Do not stare into beam, RG2 product.
Hazard RG3: not for household use symbol.
Hazard RG3: optical radiation warning symbol.
Safety

15R5906852 /06 F80
Label image Label description Label location
For F80-Q7, F80-4K7:
837
3
For North America: THIS PRODUCT IS IN CONFORMITY WITH
PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR
1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS
AUTHORIZED BY VARIANCE NUMBER 2017-V-4837 EFFECTIVE
September 13, 2017.
This projector may become RG3 when an interchangeable lens with throw
ratio greater than 3.5 is installed. Refer to the manual for the lens list and
hazard distance before operation. Such combinations of projector and lens are
intended for professional use only, and are not intended for consumer use.
Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif
interchangeable dont le rapport de projection est supérieur à 3.5. Veuillez vous
reporter au manuel pour en savoir plus sur la liste des objectifs et la distance
de sécurité avant toute utilisation. De telles combinaisons entre projecteur et
objectif sont conçues pour des applications professionnelles uniquement et
pas pour des applications grand public.
本投影机安装透射比大于3.5的可换镜头后，可成为RG3，操作前， 请参考手
册中镜头清单和危险距离。本投影机与镜头组合仅供专业使用，非普通消费者
使用。
For F80-Q9, F80-4K9 :
837
3
For North America: THIS PRODUCT IS IN CONFORMITY WITH
PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR
1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS
AUTHORIZED BY VARIANCE NUMBER 2017-V-4837 EFFECTIVE
September 13, 2017.
This projector may become RG3 when an interchangeable lens with throw
ratio greater than 2.8 is installed. Refer to the manual for the lens list and
hazard distance before operation. Such combinations of projector and lens are
intended for professional use only, and are not intended for consumer use.
Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif
interchangeable dont le rapport de projection est supérieur à 2.8. Veuillez vous
reporter au manuel pour en savoir plus sur la liste des objectifs et la distance
de sécurité avant toute utilisation. De telles combinaisons entre projecteur et
objectif sont conçues pour des applications professionnelles uniquement et
pas pour des applications grand public.
本投影机安装透射比大于2.8的可换镜头后，可成为RG3，操作前， 请参考手
册中镜头清单和危险距离。本投影机与镜头组合仅供专业使用，非普通消费者
使用。
For F80-Q12, F80-4K12 :
Safety

R5906852 /06 F8016
Label image Label description Label location
2.2.
For North America: THIS PRODUCT IS IN CONFORMITY WITH
PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR
1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS
AUTHORIZED BY VARIANCE NUMBER 2017-V-4837 EFFECTIVE
September 13, 2017.
This projector may become RG3 when an interchangeable lens with throw
ratio greater than 2.2 is installed. Refer to the manual for the lens list and
hazard distance before operation. Such combinations of projector and lens are
intended for professional use only, and are not intended for consumer use.
Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif
interchangeable dont le rapport de projection est supérieur à 2.2. Veuillez vous
reporter au manuel pour en savoir plus sur la liste des objectifs et la distance
de sécurité avant toute utilisation. De telles combinaisons entre projecteur et
objectif sont conçues pour des applications professionnelles uniquement et
pas pour des applications grand public.
本投影机安装透射比大于2.2的可换镜头后，可成为RG3，操作前， 请参考手
册中镜头清单和危险距离。本投影机与镜头组合仅供专业使用，非普通消费者
使用。
1.4 Risk Group 3 Safety
1.4.1 General considerations
Notice on optical radiation from F80 Projector when it becomes Risk Group 3.
•For RG3, no direct exposure to the beam shall be permitted.
For RG3, operators shall control access to the beam within the hazard distance or install the product at a
height that will prevent eye exposure within the hazard distance.
•This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very
dangerous and should never be attempted.
•Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous
laser radiation exposure.
•Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.
FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED
PERSONNEL familiar with potential hazards associated with high intensity light beams.
WARNING: No direct exposure to the beam within the hazard distance shall be permitted, RG3
(Risk Group 3) IEC EN 62471-5:2015
CAUTION: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
PPE (Personal Protective Equipment) description.
A skilled person or service person shall be worn protective clothes and goggles when access to restricted
area.
Possible skin or eye damage.
Disconnect power before servicing.
Safety

17R5906852 /06 F80
1.4.2 High Brightness precautions: Hazard Distance (HD)
HD
Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the
energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the
skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the
light source is less than the HD.
Restriction Zone (RZ) based on the HD
The HD depends on the amount of lumens produced by the projector and the type of lens installed. See next
chapter“HD in function of the lens Throw Ratio (TR)”, page 20.
To protect untrained end users (as cinema visitors) the installation shall comply with the following installation
requirements: Operators shall control access to the beam within the hazard distance or install the product at
the height that will prevent spectators' eyes from being in the hazard distance. Radiation levels in excess of
the limits will not be permitted at any point less than 2.0 meter (SH) above any surface upon which persons
other than operators, performers, or employees are permitted to stand or less than 1.0 meter (SH) lateral
separation from any place where such persons are permitted to be. In non-cinema environments where
unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or
equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual's
shoulders, within the HD.
These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section
6.6.5.
The end user must understand the risk and apply protective measures based upon the hazard distance as
indicated on the label and in the user information. Installation method, barriers, detection system or other
applicable control measure shall prevent hazardous eye access to the radiation within the hazard distance.
For example, projectors that have a HD greater than 1 m and emit light into an uncontrolled area where
persons may be present should be positioned in accordance with “the fixed projector installation”parameters,
resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the
floor level. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum
separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by
an individual sitting on another individual's shoulders, within the HD. For example, a sufficiently large
separation height may be achieved by mounting the image projector on the ceiling or through the use of
physical barriers.
RA
TH
PR
HD
SW
SW
SW
SW
(B) TOP VIEW
EXIT
SH
LRZ
RA
PR
TH
HD
(A) SIDE VIEW
RZ
SH
LRZ
RZ
Image 1–1
ASide view.
BTop view.
RA Restricted Access location (boot area of projector).
PR Projector.
TH Theater.
RZ Restriction Zone in the theater.
SH Separation Height.
SW Separation Width.
Based on national requirements, no person is allowed to enter the projected beam within the zone between
the projection lens and the related hazard distance (HD). This shall be physically impossible by creating
sufficient separation height or by placing barriers. The minimum separation height takes into account the
surface upon which persons other than operator, performers or employees are permitted to stand.
Safety

R5906852 /06 F8018
OnImage 1–2a typical setup is displayed. It must be verified if these minimum requirements are met. If
required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier,
like a red rope as illustrated in Image 1–2.
The restricted area sticker can be replaced by a sticker with only the symbol.
PR
RZ
RESTRICTED
AREA
RESTRICTED
AREA
Image 1–2
USA market
For LIPs (Laser Illuminated Projectors) installed in the USA market other restriction zone conditions apply.
LIPs for installation in restrained environment (cinema theaters, business rooms, class rooms, museums ...)
shall be installed at height vertically above the floor such that the bottom plane of the hazard distance zone
shall be no lower than 2.5 meters above the floor. Horizontal clearance to the hazard distance zone shall be
not less than 1 meter. Alternatively, in case the height of the separation barrier for the horizontal clearance is
at least 1 meter high then the horizontal clearance (SW) can be reduced to:
•0 meter if the height of the hazard zone is minimum 2.5 meter.
•0.1 meter if the height of the hazard zone is minimum 2.4 meter.
•0.6 meter if the height of the hazard zone is minimum 2.2 meter.
LIPs for installations in unrestrained environment (concerts, ...) shall be installed at a height vertically above
the floor such that the bottom plane of the Hazard distance Zone shall be no lower than 3 meters above the
floor. Horizontal clearance to the hazard distance zone shall be not less than 2.5 meters. Any human access
horizontally to the Hazard Zone, if applicable, shall be restricted by barriers. If human access is possible in an
unsupervised environment, the horizontal or vertical clearances shall be increased to prevent exposure to the
hazard distance zone.
The LIP shall be installed by Barco or by a trained and Barco-authorized installer or shall only be transferred to
laser light show variance holders. This is applicable for dealers and distributors since they may need to install
the LIP (demo install) and/or they transfer (sell, rent, lease) the LIP. Variance holders may currently hold a
variance for production of Class IIIB and IV laser light shows and/or for incorporating RG3 LIPs. Laser light
show variance can be requested via the FDA online eSubmitter portal or via FDA Form 3147 referencing to
Barco’s variance approval 2017-V-4837.
The installation checklist for laser illuminated RG3 projectors must be fully completed after the installation.
The installation checklist can be downloaded from the Barco website. The last variance holder in the
distribution chain is responsible to maintain the installation checklist and to make it available on request of the
FDA. In case Barco is the last variance holder the checklist must be sent to [email protected].
In addition to temporary installations (e. g.: rental and staging, lease, events …) the following requirements
apply:
•Rental companies shall have a laser light show variance because they have direct relationship with the
installers of the rented equipment.
•This product shall be located in such a way that all propagating beam paths within the Restriction Zone,
and the audience can be directly observed at all times.
•Communication shall be maintained with other personnel assisting in surveillance of the LIP projection.
•In the event of any unsafe condition, immediately terminates (or designate the termination) of LIP
projection light.
Safety

19R5906852 /06 F80
Install one or more readily accessible controls to immediately terminate LIP projection light. The power input at
the projector side is considered as a reliable disconnect device. When required to switch off the projector,
disconnect the power cord at the projector side. In case the power input at the projector side is not accessible
(e. g. truss mount), the socket outlet supplying the projector shall be installed nearby the projector and be
easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
1.4.3 HD for fully enclosed projection systems
HD
Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the
energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the
skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the
light source is less than the HD.
Restriction Zone (RZ) based on the HD
The projector is also suitable for rear projection applications; projecting a beam onto a defuse coated
projection screen. As displayed in Image 1–3two areas should be considered: the restricted enclosed
projection area (RA) and the observation area (TH).
RA TH
sw
PD
HDDIFFUSE
sw
RZ
sw sw
PR
HD
REFLECTION
RESTRICTED
AREA
RESTRICTED
AREA
Image 1–3
RA Restricted Access location (enclosed projection area).
PR Projector.
TH Theater (observation area).
RZ Restriction Zone.
PD Projection Distance.
SW Separation Width. Must be minimum 1 meter.
For this type of setup 3 different HD shall be considered:
•HD as discussed in “High Brightness precautions: Hazard Distance (HD)”, page 17, relevant for intrabeam
exposure.
•HDreflection : the distance that has to be kept restrictive related to the reflected light from the rear projection
screen.
•HDdiffuse : the relevant distance to be considered while observing the diffuse surface of the rear projection
screen.
As described in “High Brightness precautions: Hazard Distance (HD)”, page 17, it is mandatory to create a
restricted zone within the beam areas closer than any HD. In the enclosed projection area the combination of
two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into
account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to
the rear reflection from the screen (HDreflection); also taking into account a 1 meter lateral separation.
The HDreflection distance equals 25% of the difference between the determined HD distance and the projection
distance to the rear projection screen. To determine the HD distance for the used lens and projector model see
chapter “HD in function of the lens Throw Ratio (TR)”, page 20.
HDreflection = 25% (HD – PD)
Safety

R5906852 /06 F8020
The light emitted from the screen within the observation shall never exceed the RG2 exposure limit,
determined at 10 cm. The HDdiffuse can be neglected if the measured light at the screen surface is below 5000
cd/m² or 15000 LUX.
1.4.4 HD in function of the lens Throw Ratio (TR)
TR (Throw Ratio)
The ratio of the distance to the screen (throw) to the screen width.
HD versus Throw Ratio
0
1
2
3
4
5
1
1.2 1.4 1.6 1.8
2
2.2 2.4 2.6 2.8
3
3.2 3.4 3.6 3.8
4
4.2 4.4 4.6 4.8
5
5.2 5.4 5.6 5.8
6
6.2 6.4 6.6 6.8
7
7.2 7.4 7.6 7.8
8
8.2 8.4 8.6 8.8
9
9.2 9.4 9.6 9.8
10
Hazard distance [m]
Throw Ra!o
F80-Q12, F80-4K12 F80-Q9, F80-4K9 F80-Q7, F80-4K7
1
2
3
1 2 3
Image 1–4
Graph shows Hazard Distance in meters versus Throw ratio of the lens
Safety