barkman Quarry Stone User manual

Barkman Landscape Kits
Quarry Stone
Fire Pit
133670

2
06-2021 |For manual updates, check BarkmanConcrete.com/resources
This kit measures 12 x 28 x 28 (inside)
MATERIALS INCLUDED:
• 12" x 8" Quarry Stone – 36 pieces
• Spark Arrestor
• Gloves
• Instruction Guide
SOLD SEPARATELY :
• Steel Fire Pit Liner
OTHER ITEMS NEEDED:
• Measuring Tape/Ruler
• Level
Materials
12 x 8
Quarry Stone
Spark
Arrestor
Steel Fire Pit
Liner (Sold Separately)
Base Preparation
For installation on an unstructured
base, please follow these steps:
1. Mark out the location for your fire pit.
Excavate area approx. 5" below grade.
2. Excavate approx. 6" larger than your
actual kit dimensions to ensure a
stable base
Read Prior to Installation
REGULATIONS
1. The consumer is responsible for reviewing
the local regulations pertaining to the
installation and use of this product.
Please confirm that use of this product
is in compliance with the by-laws,
regulations, building codes and laws
of your jurisdiction before using.
2. Locate your respective gas lines, wires,
water pipes, and/or any above ground
and underground services in your area.
Install your Barkman fire pit kit the proper
distance away from them. Check with
your provider for location and distance
requirements prior to installation.
3. Check with your insurance provider
concerning the installation, use,
value implications and/or any other
considerations in regard to your fire pit.
LONG TERM USE
1. Barkman wall blocks are not fire-
rated and are not covered under the
Barkman warranty. It is the customer’s
responsibility to ensure that the wall
blocks are adequately protected.
Firebricks or a fire pit liner are
recommended to improve the integrity
of the product.
3. Fill 4" with 3/4" limestone and
compact.
4. Level out 1" of sand and install kit as
per the instruction guide.
For installation on a solid base such as
an existing patio:
1. Once installed, insulate the patio from
the fire using all-purpose sand or rock
to fill in the fire pit.
2. Base prep and excavation is not
necessary. Proceed to Step 1.
2. Barkman fire pit liners will eventually
rust aer prolonged fire exposure. An
oil-based rust paint spray can be used for
added protection or aer rust occurs.
3. This fire pit is not suitable for large fires.
Do not allow flame to contact the top
layer. Fire pits should not be placed
directly on concrete as high heat can
adversely aect the integrity of the
product.

306-2021
Instructions
2
A The second layer uses pattern B,
which is oset from the previous
pattern.
USE:
(12) Quarry Stone blocks
3
A Repeat the pattern from Step 1 as
shown in the diagram.
B (Optional) If a Steel Fire Pit Liner was
purchased, install in center of fire pit.
C Place Spark Arrestor on top of Quarry
Stone or Steel Fire Pit Liner.
USE:
(12) Quarry Stone blocks
Spark Arrestor
Note: The spark arrestor and liner retain
heat long aer use. Ensure both are cool
before touching.
1
A On your selected location, lay out the
first layer using pattern A.
B Ensure that this layer is level to allow
for a proper installation.
USE:
(12) Quarry Stone blocks

  
BarkmanConcrete.com
STEINBACH OFFICE
152 Brandt Street,
Steinbach, MB R5G 0R2
T 204 326 3445 or 1 800 461 2278
F 204 326 5915
[e-mail]
WINNIPEG OFFICE
901 Gateway Road,
Winnipeg, MB R2K 3L1
T 204 667 3310 or 1 800 342 2879
F 204 663 4854
[e-mail]
CALGARY OFFICE
813 McCool Street, Box 1136,
Crossfield, AB T0M 0S0
T 403 946 4630 F 403 946 4631
[e-mail]
VANCOUVER OFFICE
2104-290 Newport Drive,
Port Moody, BC V3H 5N2
T 778 689 7670 or 1 800 461 2278
F 604 949 0321
Vanc[email protected]om
SASKATOON DISTRIBUTION CENTER
3550 Idylwyld Drive North,
Saskatoon, SK S7L 6G3
T 1 306 549 7544
KELOWNA DISTRIBUTION CENTER
1904 Old Okanagan Highway,
Westbank, BC V4T 1T8
T 1 204 346 9490
SURREY DISTRIBUTION CENTER
8157 132nd Street,
Surrey, BC V3W 4N5
T 1 204 346 9490