barrier MEZZANINE GATE Operating and maintenance manual

MEZZANINE GATE
Installation Procedure
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
Optional Double Rail U-Bars

MEZZANINE GATE Installation Procedure
1
29
0
D
R
I
LL
T
H
R
O
UG
H
t
o
s
u
i
t
M
6
1
208
1
118
x 1
x 1
x 1 x 1
x 2
x 1
x 2
x 4
x 2
x 1
M
8
N
y
l
o
ck
N
u
t
M
8
x
35
H
ex
b
o
l
t
M
8
W
a
s
h
e
r
M
12
CONTENTS
x 1
x 1
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
D
H
G
ABC
E F
IJ

MEZZANINE GATE Installation Procedure
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
G
a
p
s
h
o
u
l
d
n
o
t
exce
e
d
100
m
m
x 4
STEP 1
M
1
2
Note:
Ensure to choose appropriate
fixing to suit flooring
STEP 1
G
E
200
2002
1602 200
119
2001508200
200 1259 200
200
1603
200
130
DROP
*Footprint layout as shown is for standard MZ1500-A.

MEZZANINE GATE Installation Procedure
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
STEP 2
x 6
M
1
2
x 1
x 1
x 1
STEP 2
G
A
B
C

MEZZANINE GATE Installation Procedure
x 4
x 2
STEP 3
STEP 4
1
3
0
0
S
T
A
N
D
A
RD
a
d
j
u
s
t
t
o
s
u
i
t
a
s
r
e
q
u
i
r
e
d
M
8
Note:
To ensure square connector I is a slip fit onto square shaft on H post,
remove any galvanising build up at both end from inss ide I prior ato ssembly.
CAUTION: DO NOT force I onto square shaft on H post,
as it could casue damage to aluminium bushes.
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
STEP 3
STEP 4
I
H
G
G
A
B
C
E
E
A
B
C

MEZZANINE GATE Installation Procedure
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
STEP 5
R ECOMMENDE 004D
D
H
STEP 5
G
A
B
C
E

MEZZANINE GATE Installation Procedure
IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
STEP 6
M
1
2
CAUTION message
must be applied
on rail prior operation
STEP 6
F
H
G
E

IP33 – Mezzanine Gate © Copyright 2016 www.barriergroup.com.au
MEZZANINE GATE Installation Procedure
Optional U-Bars
When side in-fills are
required, optional surface
mount U-Bars are available
in a range of standard size
UBD100SM-G,
UBD150SM-G,
UBD200SM-G
Optional Reinforment Plate
When mounting posts on timber
or unsupported floors, the optional
reinforment plate provides
additional support to the post.
WARNING
The gate will not provide optimum performance unless it is installed correctly. For
satisfactory gate operation please follow the instructions carefully.
NOTE: No guarantee will be given or responsibility accepted by the manufacturers if the gate
is not installed as instructed. Barrier Group do not warrant the work of 3rd party contractors.
BEFORE YOU START
1. The installer must ensure the desired mounting point for the gate is level, plumb and rigid.
2. Use fixings appropriate to the material into which they are being fixed (not included).
3. Check all parts are included. Contact Barrier Group immediately if you are missing a piece.
AFTER INSTALLATION CARE
Barrier Group recommends that you check the operation of your gate at least every six
months (more regularly in extreme environments or frequent use). It is natural for spring
assistance unit to lose tension over time. Adjustment may be required.
Important information.
Read carefully.
Keep this information for further reference.