BARRON Trace-Lite TL205 User manual

TL205
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
•Installation and servicing of this equipment should be performed by qualified service personnel only.
•Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
•Do not mount near gas or electrical heaters.
•Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any
modification or use of non-original components will void the warranty and product liability.
•Do not use this equipment for other than intended use.
800 533.3948 •www.barronltg.com
1
20070044 REV 2 - 12/13
1. Mount housing assembly to desired bracket using the provided mounting bolt. An optional mounting yoke or pole
tenon mount are also available.
2. Care should be taken when mounting fixture not to pinch leads.
3. Open “Ballast Housing” cover by loosening (4) Phillips captive screws.
4. Electrical connections should be made inside fixture. Cap all unused leads to prevent shorting. This fixture is pre-wired
for 277 volt; make sure supply line voltage is 277 volt. For alternate line voltage select proper ballast lead to match
your line voltage.
a. Connect the line fixture lead to the black supply lead.
b. Connect the common fixture lead to the white supply lead
c. Connect the ground lead form the service to the green grounding screw.
5. Use approved connectors to connect fixture leads to supply leads and make wire splices inside fixture. Use rated
connectors of 600V 150°C, UL listed.
6. Close “Ballast Housing” cover by tightening (4) Phillips captive screws, ensure wires are not pinched.

TL205
INSTALLATION INSTRUCTIONS
800 533.3948 •www.barronltg.com
2
20070044 REV 2 - 12/13
OPTICAL ASSEMBLY INSTALLATION
1. Remove a minimum of 3 screws from the reflector mounting
neck.
2. Orient reflector so the aiming sight is pointed up and the hinge
is pointed down.
3. Push reflector against the mounting neck so the one remaining
screw head pass thru the keyhole slot.
4. Rotate reflector so the screw head is in the narrow
end of the keyhole slot. Install remaining (3) screws and tighten
to secure reflector.
5. Loosen the (2) Phillips hinge safety screws located on the
reflector to allow the installation of the lens frame hinge “T”.
6. Close the lens frame assembly against the reflector, make sure
the gasket is seated properly and snap the latches
over the lid of the reflector to secure the lens assembly.
7.Tighten hinge safety screws.
CARE AND MAINTENANCE
For optimum performance periodically clean reflector and lens with a soft, damp rag. DO NOT use abrasive materials,
glass cleaner or other solvents on lens or paint. Use only non-abrasive glass cleaner, mild soapy water and rinse with
clean water.
TROUBLESHOOTING CHECKLIST
1. Check your power source.
2. If power is on and lamp does not burn. Turn power source off. Lock out to prevent power being restored.
3. Check electrical connections.
4. Check to insure proper seating of lamp.
5. Restore power.
6. Check if lamp is burned out.
REPLACING LAMP INSTRUCTIONS
1. When re-lamping, turn power off and allow the fixture to cool.
2. Prior to installing the lamp in the fixture, check the lamp is of proper type and wattage.
3. Screw the lamp into the socket, back the lamp out slightly then screw the lamp securely back in to make sure it is
properly seated in the socket.
4. Close the diffuser and secure with screws. Be sure that the gasket is firmly seated in the proper channel prior to
closing fixture to maintain weather-tight seal.
Note: Replace only with a lamp of same type and wattage as indicated on the fixture product label.