Bartec Pixavi Series Instruction Manual

BARTEC GmbH
Max
-
Eyth
-
Straße
16
Fon
:
+49 7931
597
-
0
Support:
em
-
[email protected]
97980 Bad
Mergentheim
F
ax:
[phone]
-
119
Download:
http://automation.bartec.de
GERMANY
Internet:
www.bartec.com
FAQ – Frequently Asked Question
Pixavi Phone
Connection to BCS3678ex scanner
 Connection via Bluetooth settings
 Connection via Zebra Scan-To-Connect application
Relevant for
 Pixavi Phone
Status: April 2021
Reservation: Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.

Table of content Agile X IS
Installation manual: Battery Status Info
1/7 Subject to technical changes.
09/2020
Subject to technical changes.
04/2021
1. Information of this FAQ ........................................................................................................................ 2
2. Connection via Bluetooth settings ...................................................................................................... 3
3. Connection via Zebra Scan-To-Connect application ......................................................................... 6

Agile X IS
Installation manual: Battery Status Info Installation manual
Subject to technical changes.
04/2021 2/7
1. Information of this FAQ
Read carefully before commissioning the device.
The FAQ is an additional description to the available user manual and part of the device.
The FAQ is directed at all persons who are entrusted with handling the device.
Knowledge of the safety instructions and warnings in this FAQ and strict compliance with them
is essential for safe handling.
‒ Carefully read the FAQ and especially the safety instructions before using the device.
‒ Make the FAQ accessible to all people who are entrusted with handling the device.
Warnings are used in this User Manual to warn of the risks of damage to property and personal
injuries.
2. Required Hardware
 Pixavi Phone
 Barcode scanner BCS3678ex-IS or BCS3678ex-NI
Symbol Explanation
Important advice and information for the effective, efficient and environmentally
sound use of the product.
Condition that must be met before the subsequent actions can be performed.
Individual steps you must take.
1., 2., … Various steps to be performed in the order specified.
Indication of the results of a step or of several steps for monitoring success.
The same described procedures should work on all other Android based devices.

Installation manual Agile X IS
Installation manual: Battery Status Info
3/7 Subject to technical changes.
09/2020
Subject to technical changes.
04/2021
3. Connection via Bluetooth settings
Optional steps to reset the scanner to factory default and delete all existing Bluetooth
connections.
1. Set the BCS3678ex scanner to Factory Defaults.
2. Unpairing all connections of the BCS3678 scanner.
Steps to establishing a Bluetooth connection between the barcode scanner and Pixavi Phone.
1. Scan the “HID BT LE (Discoverable)”.
Enables the host to establish an HID (Human Interface Device) Keyboard Profile connection
with the scanner over Bluetooth Low Energy radio. The scanner is discoverable (Peripheral
mode).
To establish a connection (initial setup only):
- Scan the HID BT LE (Discoverable) barcode.
- From the host, discover Bluetooth devices
- Select your scanner from your discovered device list.

Agile X IS
Installation manual: Battery Status Info Installation manual
Subject to technical changes.
04/2021 4/7
2. Turn on Bluetooth on the Pixavi Phone.
3. Open the Bluetooth settings and tab on “Pair new device”.

Installation manual Agile X IS
Installation manual: Battery Status Info
5/7 Subject to technical changes.
09/2020
Subject to technical changes.
04/2021
4. Select the barcode scanner.
5. If the connection is successful, the scanner appears in the section “Currently connected” with
its name and serial number.

Agile X IS
Installation manual: Battery Status Info Installation manual
Subject to technical changes.
04/2021 6/7
4. Connection via Zebra Scan-To-Connect application
Optional steps to reset the scanner to factory default and delete all existing Bluetooth
connections.
1. Set the BCS3678ex scanner to Factory Defaults.
2. Unpairing all connections of the BCS3678ex scanner.
Steps to establishing a Bluetooth connection between the barcode scanner and Pixavi Phone
via Zebra Scan-to-Connect utility.
1. Scan-to-Connect utility is available as a “.apk” file download or in the Google Play store.
Download the “.apk” file of Scan-To-Connect Utility from the Zebra Website:
Link to Zebra support & download page
Install it directly from Google Play Store.
Scan-To-Connect Utility for Android
The Scan-To-Connect (STC) Utility enables a Zebra/BARTEC (BCS3678ex) Bluetooth
scanner to pair to a phone or tablet in one simple step, without having to modify your app.
Unlike standard HID keyboards, the STC Utility supports an enhanced HID keyboard, which
assures your data is received by your phone or tablet. If corrupted, it will be retransmitted.
If lost, you get an error beep to rescan the item.
The STC Utility also has a virtual keyboard to manually enter data for items that are not
barcoded, or if the barcode is unreadable (ie. Damaged).

Installation manual Agile X IS
Installation manual: Battery Status Info
7/7 Subject to technical changes.
09/2020
Subject to technical changes.
04/2021
2. If you use the “.apk” file then copy the file to your Pixavi Phone and start the installation with
tab on it. After Installation executes the application.

Agile X IS
Installation manual: Battery Status Info Installation manual
Subject to technical changes.
04/2021 8/7
3. The Scan-to-Connect utility automatically generates a pairing barcode.
Scan the pairing barcode with the BCS3678ex scanner to establish the connection.