Base EXTRACTOR FANS User manual

2010
Instruction
Manual
EXTRACTOR FANS

APPLICATION
Base fans are designed for the ventilation
of domestic kitchens, bathrooms, shower
rooms and toilets.
Fans are for extract only and are designed
for wall or ceiling mounting.
However, please refer to the guidelines on
the product packaging to ensore appropriate
production selection.
BASIC SPECIFICATIONS
Fan identification, diagrammatic representation
dimensions are .
The fans are designed for operation from AC power supply with
voltage of 220-240 V and frequency of 50 Hz.
Nominal output:
- for 100
5
Nominal power:
for fans with 100 mm outlet capacity: - 14 W
for fans with 150 mm outlet capacity: - 24 W
ound level at 3 m distance does not exceed 40 dBA.
Fans are designed for operation at air temperature
within 0°С to 45°С.
and
shown on page 3
an
within a
For installations in close proximity to potential water hazards
(zones 1 and 2 e.g. above a bath or within a shower cubicle) a
12V fan must be fitted.
fans with 100 mm outlet: m /hr ( 5 %)
- for fans with 150 mm outlet: 29 m /hr ( 5 %)
San of
3
3
2
Design of the fans is constantly improved and updated,
and some modelsmay differ from what is described in this manual.

3
B1*
B15*
* all models-
c
a
e
b
b
a
B15
B1
Type
205
150
a
165
120
b
132
108
c
150
100
d
13
12
e
BR15 15 116 150 188
BR1 12 99 100 141
Type a b c d
Axial wall Fans
Round Axial Wall Fans
B1D
B15D
*
*For m with ingounting duct connected on both sides.
B15D 128
B1D 113
Type a b c d e f
162
110 150 100 200 160 29
29 184
144
In-line Duct Fans
d
a
e
BR15*
BR1*
* all models-
* all models-

4
SAFETY REQUIREMENTS
The fan complies with the requirements according to
EU norms and directives, to the relevant EU-Low Voltage
Equipment Directives , EU-Directives on Electromagnetic
Compatibility.
Level of protection from access to hazardous
parts and :
IPX4 -
I 34 -
Connection of fans to power supply as well as replacement
of should be performed by electrician.
Fan operation beyond the operational temperature
range as well as in rooms with ambient air containing
aggressive .
current
and
resistance to moisture
B1D, B15D range.
P B1, B15, BR1, BR15 range.
the
cables a qualified
stated
chemicals must be avoided
Ensure that the fan blade is free to rotate.
Do not install a fan in any room containing an open-flue
appliance.
CAUTION:
PREPARATION
All maintenance works and
connection of fans are to be performed
only after switching off .
Connection of fans to power supply
through switch with
not less than 3 mm all poles.
Direction of air is direction of arrow on the
fan case.
fans are mounting in ventilation duct
ther models are mounted on the wall
or ceiling with .
If necessary, ensure conditions to prevent access
to impeller and current-carrying parts of fan by
protective means from side of (ventilation
grille, protective cowl ).
Connection of fans to electric power supply
is shown in ig 1 2.
CAUTION:
the power supply
the must be
a contact separation of
in
flow in
D for ing.
Oscrews and rawlplugs
outlet
etc
f s and

5
In-line Fans
1 - housing
2 - clamp for power supply
3 - holes for power supply
4 -
cable
cable
terminal block
1
2
3
43
Fig. 2
5
4
1
7
3
6
2
9
8
1 - housing
2 -
3 - hole for power supply
4 -
5 - holes for fan mounting
6 -
7 - pull cord switch
8 -
9 -
support for power supply cable
cable
terminal block screws
cable support
timer adjustment
humidity adjustment
Axial Fans
INSTALLATION:
Remove (except model ).
Remove co .
Pass power supply through hole 3
retaining screw and fascia in-line s
retaining screw and central wiring ver
cable t at and connect
to terminal block at 4. Strip primary and secondary insulation
as necessary. Relif cover, fascia and retaining screws.
Wiring diagrams are shown in figs 3 to 6.
Fig. 1

Fig. 3
S
Power supply feed circuit for fans with built-in switch
Fig. 4
Diagram of connection of fan without built-in switch
to circuit, where 8 is switch installed additionally.
LT
LT
Fig. 5
Diagram of connection of fan equipped with timer /
timer with humidity relay and built-in switch.
Fig. 6
Diagram of connection of fan equipped with timer /
timer with humidity relay and without built-in switch.
ig . 3 operation of fans, equipped with built-in switch.
ig . show connection of fans without
built-in switch. switch is shown.
Fan switch off delay time is adjustable within the range of
approx 2 to 30 minutes. Time can be regulated by
potentiometer T.
Delay-increase direction is clockwise, and
delay-decrease is anticlockwise.
Fans supplied with timer and humidity relay are
by humidity level and are regulated by
potentiometer H by rotaiton clockwise to increase and
anticlockwise to decrease level (50-90% .
.
Diagram in ig. 6 shows connectionof lighting to fan's timer,
controlled by single switch ( is an switch).
F s and 5 for
F s 4 and 6 External S
energised
increased s
RH)
Do not regulate timer’s delay time unless fan is switched
off from the mains
fS external
S
N
L
220-240 V
220-240 V
220-240 V
220-240 V
N
L
N
L
L
NDiagram of connection of 12 an
equipped with timer. V F to transformer
LT S220-240 V
L
N
TRANSFORMER
12 V
Fig. 7
6

MAINTENANCE
Fan maintenance should be performed only
after switching off mains. Maintenance chiefly
consists of periodic cleaning of the fan's
surfaces of duct and dirt. The fan should be
cleaned with soft cloth wetted in soapy water.
After cleaning, the surfaces should be wiped dry.
STORAGE
Fan should be stored in original manufacturer's
container at a temperature
+5 С and + 40 С and relative air humidity
80% (at T = 25 С).
between
not more than
0 0
0
GUARANTEE
The m
for from purchase correct
installationand adequate maintenance. If proof of purchase
date is not available then guarantee
m
the a only.
seller.
anufacturer hereby guarantees normal performance of the
fan 36 months the date of subject to
the term is calculated from
the date of manufacture. In case of fault in operation of the fan
through the fault of the anufacturer within the warranty term,
consumer shall be eligible for free replacement
Warranty replacement is performed by
ACCEPTANCE CERTIFICATE
The fan has been duly certified as serviceable
Model Manufactured on (date):
Approval mark
Sold
Name of , stamp of storeretailer
Date of sale:
BASE 01 EN-14

Polypipe Ventilation
www.polypipe.com/ventilation
[e-mail]