BASETech 3DP1 User manual

• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public
supply.
• Before plugging in the power adaptor, check whether the voltage stated on the
power adaptor complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during
storms.
• If the wall plug transformer is damaged, do not touch it; there is danger to life from
electric shock! First, switch off the mains voltage to the mains socket to which the
wall plug transformer is connected (switch off at the corresponding circuit breaker
or remove the safety fuse, then switch off at the corresponding RCD protective
switch, so that all poles of the mains socket are disconnected). You can then
unplug the wall plug transformer from the mains socket. Dispose of the faulty
wall plug transformer in an environmentally friendly way; do not use it any more.
Replace it with a wall plug transformer of the same design.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. The plug-in
power supply unit also involves danger to life by electric shock! Allow the product
to reach room temperature before connecting it to the power supply and putting it
to use. This may take several hours.
• Never pour any liquids over electrical devices or put objects lled with liquid
right next to the device. If liquid or an object enters the interior of the device
nevertheless, rst power down the respective socket (e.g. switch off circuit
breaker) and then pull the mains plug from the mains socket. Do not operate the
product anymore afterwards, but take it to a specialist workshop.
• In schools, training facilities, hobby or self-service workshops, handling of
electrical devices must be monitored by trained personnel.
• When operating on commercial premises, the relevant accident prevention
regulations of workers’ compensation boards for electrical equipment must be
observed.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Maintenance, modications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Operating elements
1
2
3
9
4
5
8
6
7
1 Feed opening
2 DC-socket
3 Temperature and material control
4 LED heating indicator green
5 LED operation indicator red
6 Unload button
7 Speed control
8 Feed button
9 Nozzle tip
Operating Instructions
3D Printing Pen 3DP1
Item No. 1646098
Intended use
The product is used to create three-dimensional objects made of plastic lament. A heating
element inside the pen heats the plastic lament. At the push of a button, the nozzle extrudes
a thin thread of lament that hardens in the air. The product is powered via the power adaptor
which is included in delivery.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.
in bathrooms) must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, res, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• 3D printing pen
• Small plastic tool
• 3x PLA-lament (3 m)
• 2x stencil
• Power adapter
• USB cable (1.2 m)
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
This symbol warns you of hot surfaces.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• This appliance may be used by children over 8 years of age and people with
reduced physical, sensory or mental capabilities if they have been given
supervision or instruction concerning the safe use of the appliance and understand
the potential hazards.
• Children must not clean or service the product without appropriate supervision.
• Children should always be supervised by an adult to ensure that they do not play
with the appliance.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, steam and solvents.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Do not place the product under any mechanical stress.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Feed only suitable lament into the feed opening.
• Caution. Do not touch the nozzle tip during operation because it is very hot. Risk
of burns!
• The mains outlet must be located near to the device and be easily accessible.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1646098_v1_1018_02_hk_m_en
Select lament type
• Open the cover of the temperature and material control (3).
7A
103
B
PLA
PLA 190 ºC
ABS 210 ºC
140 ºC
174 ºC
160 ºC 130 ºC
240 ºC
• Use the delivered small plastic tool to set the lament
at the temperature and material control. Use only
PLA and ABS with a diameter of 1.75 mm. The preset
temperature is 190 ºC for PLA and 210 ºC for ABS. You
can adjust the temperature in steps. The temperature
range is 130 - 240 ºC. You can also perform the
adjustment during operation. See illustration.
An incorrect temperature setting can cause material jamming.
• Before feeding the lament kindly observe that the end of the lament is at and straight.
Please see illustrations below.
7A
103
B
PLA ABS
7A
103
B
PLA ABS
7A
103
B
PLA ABS
correct wrong wrong
Operation
Warning! The nozzle tip (9) is very hot during operation. Do not touch! Risk of burns!
Never touch the nozzle or the rubber area at the pen tip during and immediately after
operation. Also inform other people in the immediate vicinity.
The extruded lament is very hot for a short time. Do not touch! Risk of burns!
Unload excess lament from the pen after use and before storing. Disconnect the
product from the power supply. Place the product in the pen holder.
Direct contact with the hot tip will cause damage to painted surfaces, plastics and
clothing.
Inhaling toxic fumes can lead to serious illness. If necessary, use a suitable smoke
mask or smoke extraction system.
Do not use poor quality laments.
Do not use ABS lament in PLA mode and vice versa.
a) Connecting the power adapter
• Connect the USB-A plug of the USB cable with the power adapter.
• Connect the DC plug with the DC socket (2).
• Connect the mains plug of the power adaptor to a standard mains socket.
• The red LED operation indicator (5) lights up.
You can also use the product with a suitable power bank (output: 5 V/DC, 2A).
b) Feed lament and extrude
• Select the lament type you would like to use. Check whether the material setting is correct
and that the lament is at and straight. See section “Select lament type”.
• Feed the lament into the feed opening (1). Press the feed button (8). The green heating
indicator (4) starts to ash and the product preheats. Preheating lasts about 45 seconds. As
soon as the working temperature is reached, the ashing stopps and the heating indicator
lights steady.
• Double click the feed button and the lament will be extruded. You can also hold the feed
button depressed to extrude the lament. Release the feed button to stop the extrusion.
• As soon as the molten material leaves the nozzle tip (9) you can start with your creation.
• Adjust the extrusion speed steplessly with the speed control (7).
• Press the feed button once to stop the extrusion of the lament. Extrusion starts again after
applying a double click on the feed button.
c) Fine temperature adjustment
Filaments of different colours have different melting points. Therefore you may need to adjust
the temperature for the best results. Please follow these rules:
• If you hear a sputtering sound and/or many bubbles are visible, the temperature is too high.
Reduce the temperature.
• When using PLA lament, if the extruded material is too thin and liquid, the temperature is too
high. Reduce the temperature.
• If the colour of the extruded material is a dull colour and the motor coughs, the temperature
is too low. Increase the temperature.
• Normally, the extruded material should be soft and smooth. There should be no or only a
few bubbles.
Material unload and change
• Unload the material before you stow away the product.
• During operation apply a double click at the unload button (6) (green LED heating indicator
lights up steadily) and the material will be fed in reverse direction out of the feed opening (1).
• Gently pull the material out. Thereafter press the unload button once to stop the motor.
• If you would like to use the same material in a different colour, you can feed it directly or you
can unload the previous material rst.
• If you would like to use a different material you must unload the previous material rst.
Thereafter disconnect the power supply for about 5 seconds in order to restart the printing
pen. Then select the lament type as described.
Tips to avoid material jamming
• Unload the lament after your work is nished.
• If you need PLA lament instead of ABS lament feed the lament in ABS mode.
• As soon as the PLA lament leaves the nozzle change to PLA mode.
Tips to clear material jamming
• Disconnect the power supply for about 5 seconds.
• Select the ABS mode (temperature 210 °C) and wait for about 45 seconds until the product
is heated up.
• Feed the PLA lament in the ABS mode.
• Push in the PLA lament by hand until it exits the nozzle.
Troubleshooting
Possible fault Reason Suggested solution
LED operation indicator
does not light up.
Power adapator or DC plug
not properly connected.
Connect plug properly.
Defective power adaptor. Replace power adaptor.
Filament does not leave
the nozzle.
Temperature not high
enough.
Increase temperature.
No feeding of lament.
Filament not straight.
Unload lament and cut-off
straight at the end.
Working temperature can
not be reached.
Defective heating element. Product must be repaired.
Care and cleaning
• Disconnect the product from the mains before each cleaning. Let the product cool down
completely.
• Never immerse the product in water or other liquids.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, bre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulll your statutory obligations and contribute to the protection of the environment.
Technical data
a) 3D printing pen
Input voltage / current................... 5 V/DC, 2 A
Suitable lament........................... ABS or PLA (each Ø 1.75 mm)
Adjustable temperature range ...... 130 - 240 ºC
Preset temperature....................... 210 °C (ABS), 190 °C (PLA),
Ø nozzle tip / material................... 0.6 mm / ceramic
Operating conditions..................... -10 bis +55 °C, 5 – 95 % RH
Storage conditions........................ -20 bis +70 °C, 5 – 95 % RH
Dimensions (L x W x H)................ 175 x 17 x 20 mm
Weight .......................................... 40 g
b) Power adapter
Input voltage................................. 100 – 240 V/AC, 50/60 Hz
Output voltage / current................ 5 V/DC, 2 A
USB cable length.......................... 1.2 m