Battenfeld 22280 User manual

Vault Accessories
Deluxe Kit
Instructions #1031640 Product #222498
A. Hygrometer
B. 12” Dehumidier
C. Large Hanging Organizer
D. Cordless Automatic Vault Light
E. Magnetic Barrel Rest
F. Vault Anchor Kit
A.
B.
C.
D.
E.
F.

Cordless Automatic
Vault Light
Instruction #1025374 Rev A Product #222809
Instructions and Usage
Location of Controls
1. ON/OFF/DIMMER Switch
2. Battery Compartment*
3. Light Sensor Switch
1.
2.
3.
4.
Installation -- Hook and Loop Tape (included)
1. Check the location of where you want to put the vault light.
Make sure it is clean and free of debris or dust.
2. Put the two pieces of hook and loop tape together so
that the hook and loop sides adhere to each other.
NOTE: Hook and loop tape may be cut to desired size for easier removal.
3. Remove plastic covering on one side of the tape.
4. Place the tape in the center of vault light base.
This is the battery compartment side.
5. Remove plastic covering on the other side of the tape.
6. Place light in the desired location. Press rmly and hold
for ve (5) seconds for to tape adhere to the surface.
7. Make sure light sensor is facing in the direction of
ambient light source for proper operation.
CAUTION: Be cautious of what surface the hook and loop adhesive is
attached to, as it may remove paint or damage surface.
Screw (included)
1. Drill a pilot hole in the location where you want to mount the light.
The hole should be where you want the center of light to be located.
2. Put screw (included) in pre-drilled hole. Leave ½” of the screw out of the hole.
3. Slide battery cover over screw. Prongs should face down as shown.
4. Slide battery cover to the left or the right so that the neck of screw is in the narrow part
of the hole. Tighten screw until battery cover is secure to surface. Do not over tighten.
Attach vault light body to battery cover.
5. Make sure the light sensor is facing in the direction of the ambient light source
for proper operation.
4. Light Sensor
*Underneath unit

Light positioning
• The LED Vault Light’s base can be twisted 360°.
• Pivot the lens up to 30º to light desired area.
ON/OFF/DIMMER Operation
• Press power symbol once for full brightness.
• Press again for softer light.
• Press a third time to turn the light OFF.
NOTE: When using Auto ON Auto OFF Light Sensor the dimmer
feature is temporarily deactivated.
Built-in Auto On Auto Off Light Sensor
The unit comes complete with a photocell light sensor. You may choose to activate this feature to avoid having to physically press the LED vault light On
& Off during each use. The Auto On Auto Off Light Sensor is designed to turn the LED vault light On automatically when ambient light is detected. The
light sensor will also shut the LED vault light off automatically when ambient light is no longer detected.
NOTE: When using Auto ON Auto OFF Light Sensor the dimmer feature is temporarily deactivated.
Always test to make sure that the vault light is going ON and OFF properly when utilizing
the light sensor function.
Using Light Sensor:
1. Light Sensor Setting 0 (OFF): Light sensor is OFF. Activate and deactivate LED vault light manually.
2. Light Sensor Setting 1 (High Ambient Light): For use in areas with bright ambient light for activation.
3. Light Sensor Setting 2 (Low Ambient Light): For use in areas with dim ambient light for activation.
4. Place Light Sensor facing direction of ambient light source.
NOTE: Reective materials in close proximity to the LED vault light may affect the light sensor feature.
In these instances it may be best to point the light sensor away from reective materials/areas.
If the area is highly reective it is best not to use the Auto On Auto Off Light Sensor.
Inserting/Replacing the Batteries
To Install Batteries for the First Time:
Remove battery compartment housing at the back of the vault light. To do so, hold the front of the vault light in
one hand, with the other hand grab nger grips on battery compartment cover and pull away from vault light.
NOTE: It may help to turn the light head or battery compartment cover clockwise or counter-clockwise
as you are pulling it off.
To Replace Batteries Once Puck Light is Mounted:
1. Vault Light body will release from battery compartment cover/mounting bracket easily.
Place ngers around Vault Light body and pull down gently to release light head and expose battery compartment.
2. Remove old batteries (if replacing batteries).
3. Replace with three (3) new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
2. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
3. Replace all batteries of a set at the same time. Do not mix old and new batteries.
4. Clean the battery contacts and also those of the device prior to battery installation.
5. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modications to this product not approved by the party responsible for
compliance could void the user’s authority to operate the product.
Cordless Automatic Vault Light

Dehumidifier
Thank you for purchasing a LOCKDOWN Dehumidifier Rod. When properly used, it
will provide you with years of trouble free service. Please read all instructions
below before attempting to use the rod.
Safety Warnings:
- The Dehumidifier Rod is for indoor use only and is not intended for
outdoor use.
- Do not immerse unit, plug, or cord in water or allow contact with
liquids.
- Do not operate rod in presence of explosives or flammable fumes.
- Do not operate rod if cord is damaged.
- Make sure unit is unplugged when installing or handling.
- Do not use plug included with this dehumidifier on any other device.
- Do not use any other plug on this dehumidifier.
Installation Instructions:
Install Dehumidifier Rod on a dry level surface. It should be oriented horizontally and as
low as possible inside the safe.
1. Install the electrical cord through the safe wall. From the inside of the safe, push the
end of the cord through the wall to the outside. Many safes have a pre-drilled electrical
access hole near the bottom usually in the rear. If no access hole exists you will need to
drill one. If the safe features an internal electric outlet, you will not need to route the cord
through the wall of the safe.
2. Install the mounting clips to hold the rod. The rod must be mounted horizontally and
should be as low as possible in the safe. Be sure the rod will not interfere with any of the
safes hinges or locking lugs. Use the included screws to attach the clips to the safe
interior.
Product #222-000 & #222-010

3. Snap the Rod into the mounting clips.
4. Make sure the end of the wire has a clean cut end. If it does not, cut off a small amount
of the cord to achieve a clean end. Do not split the wires, see figure 1. The plug housing
has a back cover that will need to be removed, see figure 2. Once the cover is removed, you
will see two prongs, as shown in figure 3. Place the cord into the cavity with the prongs,
making sure that the cord is inserted as far into the housing as possible. Then begin to
reinstall the housing cover, as shown in figure 4 (next page). Make sure the cover is
completely shut, thus locking the cord inside the plug housing, as
shown in figure 5 (next
page). Instructions continued on next page.
5. Plug the Dehumidifier Rod into a power outlet.
Figure 1
Make sure you have a
clean cut end on the wire.
Right
Wrong
Figure 2
Remove the plug housing
cover as shown. Please
note the orientation of this
cover as it will need to be
reinstalled the same way.
Figure 3
Once the cover is removed,
you will see a channel with
two prongs. This is where
the power cord will be
installed.
Prongs
Figure 4
Place the cord in the
channel, making sure the
cord is inserted as far as it
will go. Then replace the
cover as shown.
Figure 5
Make sure the cover is
completely shut, thus
locking the power cord
inside the plug housing
as shown.
Insert power cord all the way.
CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT. FULLY INSERT. POUR EVITER LES CHOCS ELECTRIQUIES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQU’AU FOND.

Large Hanging
Organizer Instructions
High strength magnets for
metal interiors.
Vampire Clips for
fabric interiors.
Depending on which interior you have in your vault, slide the
clips up into the pockets on the back of the Handgun Hanger.
Then, attach hanger wherever you like.

Hygrometer
Instructions
Provides accurate Relative Humidity readings
from 0% to 100% inside a gun safe.
• Mounts easily with included fastener
• Large easy-to-read numbers
• 2 ¾” diameter
Hook & Loop fastener
on the back
Mount anywhere in your vault that is easily visible.
Magnetic Barrel Rest
Instructions
Magnetic back holds to any magnetic vertical surface.

Wood Floor Joist or Wall Stud:
The Anchor Kit includes Lag Screws and tted caps for installing a safe to solid wood.
This is useful when you are mounting it to wall or to oor joists. The following steps
are for installing into a oor joist, but a wall stud can also be used.
1. Remove the oor or lining of the vault until you are down to bare steel.
2. Use a stud nder to locate the center of the oor joists or studs and mark
where you want to drill the holes.
3. Measure the distance between the joists/studs and mark the inside
of the safe accordingly.
4. Using a 11mm Wood/Metal Drill Bit, drill through the bottom of the safe, but not
into the oor below (raising the vault off of the oor will make this easier).
5. Position the safe exactly where you want it to be installed.
6. Using a 7mm Pilot Drill Bit, drill through the center of the holes you just
made and straight into the oor joist at least 3 inches deep (using a pilot hole is
important for both strength and ease of assembly).
7. Use a vacuum to remove all wood chips from the holes.
8. Place a Lag Screw into each hole and using a 17mm socket and ratchet,
press down rmly and rotate to screw them into the joist. Tighten them until the
screw head is tight against the bottom of the vault.
9. Place the Hex Bolt Covers over the exposed screw heads to prevent
damage to rearms.
10. Reinstall the vault oor or lining
Vault Anchor Kit