Battenfeld Tipton Gun Vise Parts list manual

Assembly and Usage Instructions
C: Pad Assembly
1. Install the Forend Pad by rmly
pressing the 5 plugs into the holes
in the Base as shown.
2. Install the Grip Pad by pressing the
two plugs inside the Pad through the
holes in the base as shown. The pad
should “snap” into place.
3. Install the Rear Pad by sliding it
downward from the top. The two
tabs on the top and the three tabs
at the bottom of the pad should align
with the slots in the base.
2.
3.
4.
5.
Usage Instructions:
1. Place the Gun Vise on a at surface with enough clearance for the barrel to protrude out the left side.
2. Make sure the Cam Lever is turned toward the back of the Vise.
3. Place your gun into the Gun Vise as shown.
4. Turn the Cam Lever to the front of the Vise.
5. Turn the Adjustment Knob until the Clamp Pad just touches the stock.
6. Open the Cam Lever again, and turn the Adjustment Knob clockwise 2-3 more turns.
7. Turn the Clamp Lever to the front of the Vise. This should tightly clamp your gun while
allowing the Cam Lever to lock into the fully forward position.
NOTE: For best results, ensure the Clamp Pad is rmly in contact with the stock and
not positioned on the edge of the cheek piece.
Product #: 782731 Instructions #: 690000 Revision C
WARNING: THIS PRODUCT IS NOT A BENCH
REST. DO NOT SHOOT A FIREARM WHILE IT IS
CLAMPED INTO THIS PRODUCT.

Thank you for purchasing a Tipton Gun Vise. Assembly of this product is very easy and requires only a Phillips head
screwdriver. Please take a moment to locate all of the parts shown in the photo below.
1. . . . . . . . . . . . . . . . . . Gun Vise Base Assembly (1018466)
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clamp Pad (203931)
3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .Forend Pad (1018468)
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grip Pad (1000076)
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Rear Pad (1000077)
6. . . . . . . . . . . . . . . . . . . . . . . . . Pivot Arm Cover (1015872)
7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cam (527772)
8. . . . . . . . . . . . . . . . . . . . . . Cam Lever Assembly (432410)
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . Pivot Arm Pin (242621)
10. . . . . . . . . . . . . . . . . . . . . . Pivot Arm Assembly (318636)
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring (539059)
12. . . . . . . . . . . (3) ¼-20 x 1.25 Pan Head Screws (138037)
ASSEMBLY INSTRUCTIONS:
A: Pivot Arm Assembly
1. Press the Clamp Pad over the
steel washer on the Pivot Arm.
2. Insert the Pivot Arm Pin into
the large hole in the vise.
3. Install the Pivot Arm onto the pin.
NOTE: The Arm should be oriented
so that the Spring Alignment Stud
is even with the Spring Groove
as shown.
1.
2. 3.
4.
5. 6.
7.
8.
9.
10.
11.
12.
A: Pivot Arm Assembly continued
4. Slide one end of the Spring onto the
Alignment Stud and place the body
of the spring into the Spring Groove.
5. Now place the Pivot Arm Cover over
the Pivot Arm Pin and secure it with
two of the provided Screws.
NOTE: Do not over tighten
the screws. Over tightening
the screws can strip out the
plastic base.
1.
2.
3.
NOTE
4.
5.
B: Cam Assembly
1. Hold the Cam in one hand and the Cam Lever Assembly
in the other hand as shown.
2. Insert the Cam Lever into the Cam so that the Roll Pin snaps
into the slot in the Cam. The completed Cam Assembly should
be oriented like below.
3. Now slide the bottom of the Cam Lever into the hole in the
Base and secure the Cam Cover with the remaining Screw.
1.
2.
Assembled
Cam Lever
3.
A Product
5885 West Van Horn Tavern Road
Columbia MO. 65203
Visit our website at www.tiptonshooting.com
Screw Hole