Battery Controller TRADITIONAL User manual
The packaging of the product is recyclable. Do not dispose of electrical
appliances or batteries in household waste, but please follow current
regulations.
TROUBLESHOOTING
PROBLEM
SOLUTION
The charger is connected to power outlet and
jump starter’s 12V socket, but the charger’s
red LED blinks slowly (Error: battery not
connected).
Check that the jump starter’s switch is on 12V.
Verify that the jump starter’s 12V socket is working, by
connecting whatever 12V device (for example, a 12V
lamp).
The battery charger cannot complete the
charge.
One of the jump starter’s batteries might be defective or
the battery charger might be damaged. Please try
recharging another 12V battery with the battery charger
to verify whether the same problem occurs.
The battery charger works perfectly and it
completes the charge, but the jump starter’s
digital voltmeter doesn’t turn on.
The voltmeter button might be damaged. Please verify
with a voltmeter on the jump starter’s clamps the battery
voltage / state of charge..
The device is fully charged but it doesn’t
work.
Make sure the cables and clamps of the jump starters
are intact and that they are well connected to the poles
of the vehicle battery. Check there is voltage on the
clamps, otherwise check that the safety fuse is not
broken. The vehicle’s battery might be defective.
When a 12V accessory gets connected to
the 12V socket, a strange noise is heard.
The 12V adapter of the connected device could be
defective, causing the switch to interrupt. The 12V device
could require too much current.
F.A.Q.
QUESTION
ANSWER
How many jumpstarts can be done before to
recharge the jump starter?
1 to 30 jumpstarts, according to the temperature, the
vehicle’s conditions, the engine type and capacity.
Is it possible to replace the jump starter’s
battery?
Yes, please ask your Dealer for information.
Which is the best storing temperature?
Ambient temperature. The jump starter works also with
temperatures below 0°C, but it can lose power. High
temperatures bring to a faster discharge.
Can I use another battery charger to
recharge the device?
No, use only the provided battery charger BC SMART
4000.
The jump starter is a fragile product?
Yes, it is necessary to follow all instructions carefully.
TECHNICAL DATA & CONTACTS
Voltage
12/24 Volt
Peak Current (PA)
5000A 12V / 2500A 24V
Cranking Current (CA)
1700A 12V / 850A 24V
Battery Capacity
2 x 12V 22Ah
Cables Section
50 mm2
Cables Length
150 cm
External Fuse
500A
Dimensions
350 x 300 x 600 mm
Weight
21.5 Kg
BC JUMPSTARTER TRADITIONAL 12-24V
USER’S MANUAL
1. 12V/24V/OFF Switch (keep it on OFF when
the jump starter is not used)
2. 12V socket for recharging jump starter
3. Voltmeter button
4. Digital voltmeter
5. Alarm for short circuit / reverse polarity
6. Trolley handle
7. Rails for cable winding
8. Supports for clamps
Thank you for purchasing the jump starter BC JUMPSTARTER TRADITIONAL 12/24V,
provided with two sealed AGM batteries. Please always follow the basic principles and
precautions necessary when working near a 12V or 24V battery, read all the instructions
carefully and keep this user manual for reference. The device is designed exclusively for
starting vehicles with 12V or 24V lead-acid batteries.
IMPORTANT NOTE: BEFORE FIRST USE, RECHARGE THE STARTER COMPLETELY
WITH THE CHARGER BC SMART 4000 SUPPLIED.
1 - SAFETY INSTRUCTIONS
1. Keep out of reach of children or persons with reduced physical/mental abilities or lack
of experience, unless under the supervision of a responsible person. The product is not
a toy.
2. Wear protective goggles, gloves, ear muffs and appropriate clothing (never vinyl)
during use. Do not wear metal objects. Keep fire extinguisher and water handy. Make
sure there is someone who can provide assistance.
3. Use only original accessories provided and recommended by the manufacturer.
4. Any modification or alteration to the device is prohibited.
5. Never pull the charger cables, even when disconnecting the plug from the socket.
6. Do not charge the appliance with damaged accessories. In the event of damage or
failure of the supplied charger, request repair or replacement from the dealer.
7. The starter can be used in any weather conditions (rain, snow, hot or cold weather). Do
not recharge in a damp environment. Do not attempt to start a frozen battery. Do not
immerse the booster in water or liquids, do not expose to splashes.
8. Never put the red clamp in contact with the black clamp and do not place the two
clamps in contact with the same metal object, to avoid any risk of a short circuit.
9. To avoid any risk of short circuit and to protect the positive (red) and negative (black)
clamps, always hook the clamps to their supports when not in use. The appliance is
equipped with lateral rails for winding the cables.
10. Do not expose the device to flames or sources of heat. Do not smoke when using it nor
use in presence of flammable/explosive liquid/gas/dust. Use in ventilated environment.
11. In the event of faults or failures, do not attempt to repair the jump starter, but always
contact your dealer. Any tampering or attempted repair in autonomy will result in the
invalidity of the warranty.
12. Never allow the jump starter to discharge completely and charge it periodically.
Damages caused by a deep discharge may be irreversible.
1
4
3
2
1
5
8
4
6
7
7
3
4
IMPORTANT: when the jump starter is not used, we recommend to keep it always
connected to the provided charger, or at least to recharge it once every 3 months.
2 - GENERAL FEATURES
1. Battery types: 2 x 12V 22Ah AGM (Absorbed Glass Mat) sealed lead battery, according
to IATA safety norms. The AGM sealed battery allows to place and use the jump starter
in whatever position.
2. The clamps are completely insulated and the copper cables are super flexible. The
cable section is 50 mm2and 150 cm long, for maximum comfort.
3. The included battery charger BC SMART 4000 is provided with a microprocessor and
an automatic 8-steps charging algorithm. It can stay always connected to the jump
starter with no risk of damages and it can be used also for the care of other 12V
batteries.
4. Embedded 12V socket for recharging the jump starter.
5. Safety fuse placed on the positive clamp, inside the handle (slide the red cover down).
Use only recommended fuses and verify which kind of fuse is mounted on the device
before ordering spare parts. The fuse replacement is very easy: just unscrew the two
bolts that fix the fuse, replace it and retighten the two bolts.
6. 12V/24V/OFF Switch: keep the switch in OFF position when the jump starter is not
used or while connecting the clamps to the vehicle. Only after making sure that the
connection is correct, turn the switch to 12V or 24V depending on the vehicle battery.
7. Alarm for short circuit or reverse polarity: the buzzer will emit a sound or a light
when it detects a polarity inversion. It only works if the ON / OFF switch is set to OFF
position (we always recommend to keep it in OFF position while connecting the jump
starter to the vehicle).
8. Digital voltmeter showing the state of charge (see next point).
3 - INDICATION OF THE STATE OF CHARGE
1. To check the of charge of the jump starter, turn the switch to 12V position and press
the yellow button. If the voltage is below 12.7V, it is necessary to recharge the jump
starter. When leaving the booster connected to the vehicle after starting (max 10
seconds), the voltmeter indicates the alternator charge voltage.
2. When the jump starter is connected to the supplied battery charger, refer to the LED
bar of the battery charger to check the state of charge.
4 - RECHARGING THE JUMP STARTER
1. The jump starter’s kit includes the battery charger BC SMART 4000, completely
automatic with 8 charging steps. To recharge the jump starter, connect the charger to a
power outlet and to the 12V socket of the jump starter, then turn the jump starter’s
switch in 12V position. Recharge only in ventilated environments.
2. The green “CHARGE” LED of the battery charger blinks slowly during recovery and
charging, it blink fast during desulfation and it is steadily on during maintenance. The
device switches automatically from one step to the following one. For detailed
information about the charging algorithm and the charger’s operation, please refer to
the manual of the charger itself.
3. When the green LED on the charger switches to fast blinking (desulfation), the jump
starter is ready to use. However, it is recommended to wait for the green LED to be
steadily on, Anyway, jump starter can be disconnected from charger in any moment.
4. After starting a vehicle, before disconnecting the appliance, wait max 10 seconds with
the engine running, so that the alternator can recharge the jump starter's battery.
Please keep in mind that it is recommended to keep the jump starter connected with
the battery charger BC SMART 4000 when it is not used!
5 - OPERATING INSTRUCTIONS - EMERGENCY JUMP STARTING
Before jump starting the vehicle, please check that the vehicle is in neutral with the
handbrake on and the ignition key in OFF position. Read the vehicle’s manual and follow all
safety instructions. Make sure that all loads (lights, radio, air conditioning...) are switched off
and that the jump starter’s switch is in OFF position.
1. First connect the red (positive) clamp to the positive pole of the vehicle battery.
2. Next, connect the black (negative) clamp to the negative pole of the vehicle's battery or
to ground to the vehicle frame, away from the battery and the fuel line. Pay attention to
moving parts such as fan, straps, etc.
3. Turn the jump starter’s swith in 12V or 24V position, according to the vehicle to start.
4. Move away from the battery and the jump starter when it starts running and make sure
it is in a stable position so that the engine vibrations following the jumpstart do not
cause it to fall. The length of cables is enough in most cases to position the starter on
the ground.
5. Once the vehicle is started, after waiting for some minutes to allow the alternator to
recharge the internal battery, disconnect black clamp (negative) first and then red
clamp (positive).
6. Reposition both clamps immediately on their respective supports.
7. Put the device in charge with the provided battery charger BC SMART 4000.
Never use for 12V vehicles when the switch is in 24V position!!!
IMPORTANT: If the vehicle does not start within 10 seconds, do not insist. Let the jump
starter’s battery cool down for 3 minutes before to try again. Otherwise, the internal battery
could be irreversibly damaged (jump starting attempts have to be very short).
NOTE: In presence of a faulty battery, this could reject the jump starter's charge. This could
be the reason why the vehicle does not start.
6 - OPERATING INSTRUCTIONS –12V SOCKET
The jump starter’s 12V socket can be used as a portable power supply for all 12VDC
devices provided with a cigar socket adapter. The 12V socket is provided with an automatic
overload protection. Moreover, the socket can be used as a memory saver to supply a car’s
on board devices, when it’s necessary to disconnect the battery for replacement or for
maintenance operations. BC accessories range includes the adapter OBD Memory Saver
(part number 710-OBDMS) to connect the jump starter’s 12V socket directly with a car’s
OBD socket.
7 - WARRANTY
Forelettronica Srl offers a 2-years limited warranty on the jump starter for faults or
malfunctions due to materials or manufacturing. Parts whose deterioration is attributable to
use are considered excluded from the guarantee. The warranty is void in case of improper
use or tampering of any kind or repair carried out by an unauthorized technician. This
warranty is limited to the original purchaser: it is not transferable to third parties.
The warranty excludes implicit forms of warranty, including guarantees for damage caused
as a result of use of the device: Forelettronica Srl is deemed exonerated from any damage
to persons or property from the use of its products. The shipping costs for returning the
defective device are the responsibility of the purchaser.
2
3
Other Battery Controller Remote Starter manuals
