Audiovox Pursuit PRO 9232 User manual

CongratulationsonyourpurchaseofthePRO9232automotiveKeylessEntryUpgrade
Alarm System. The PRO 9232 is a state - of - the - art auto security system that is
designed to automatically arm and disarm when it receives a command from your
existingFactoryKeylessEntryTransmitter.Takingafewmomentstoreadthismanual
willhelptoensurethatyourvehicleisprotectedatalltimes.
ARMING THE SYSTEM : ( ACTIVE )
1. Turnthe ignitionkeyoff,exitthevehicle,andclosealldoors.
2. Pressandrelease the Lockbuttononthekeychain transmitter.
3. Thesirenandorhornwillbeeponetime,theparkinglampswillflashone time,and
thereddashmountedL.E.D.willbegintoslowlyflash,indicating thatthesystem
isARMED.
NOTE:If the unit beeps three times when arming, then one of the entry points
( hood, trunk, or doors ) has been left opened. Closing the hood, trunk,
or door will correct the problem, and the system will emit a single chirp
toconfirmthattheproblemhasbeencorrected. Additionally,ifilluminated
entryisafeatureoftheFactoryKeylessEntrysystem,thealarmmaychirp
3 times every time the system is armed, and chirp one additional time
whenthe interiorlightturnsoffto confirmthat alltrigger zonesarefully
operational.
4. Anytimethedoorlockswitchinthevehicleisusedtolockthedoorswhilethe
ignitionkeyisturnedoff,thesystemwillimmediatelyarm. Tolockthedoorsafter
entering the vehicle, makesuretheignition key is switchedonfirst. Turningthe
ignition key on first will stop the system from arming.
ARMING THE SYSTEM : ( PASSIVE )
1. Turnthe ignitionkeyoff,exitthevehicle,andclosealldoors.
2. ThedashmountedL.E.D.will begin to flashrapidly,indicatingthatthesystemis
automatically(passively)arming.Asanaddedconvenience,the30second
automaticpassivearmingwillnotbeginuntilalldoorsareclosed,allowingpassengers
toexitthevehicleattheirconvenience.
Model PRO 9232
OWNER’SMANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE

3. In30seconds,youwill hear a single short chip from the siren, and the vehicle’s
parkinglampswillflashonetime,indicatingthat thesystemhasARMED.Atthis
time,thereddashmountedL.E.D.will begin to flash slowly, providing a visual
indicationthatthesystemisfully armed.
4. Itispossibletoprogramthesystem,thatwhenthealarmisallowedtoautomatically
passive arm, there will be a 15 second delay after a door is opened before the
alarmwillsound.However,ifthesystemisprogrammedfor instanttriggerthere
willbenodelay. Checkwithyourinstallerfor the setting of this feature.
IMPORTANT! Whenthesystemisprogrammedforpassivearming,thesystem
willalwaysarm,evenwhenthekeychaintransmitterhasnot
been used to lock the doors.
When you leave the vehicle, and a door has been left opened, the system will
armafter10minutes. If you plantovacuum the car, or ifservicework is being
performed,eitherleavethekeyintheignitionandswitchedtotheonposition,
or put the system into valet mode. If you do not do this, the system will arm in
10minutes,and youwill probably inadvertentlytrip the alarm.
PROTECTION WHILE THE SYSTEM IS ARMED :
1. Openinganydoor,hood,ortrunkwillcausethealarmtoimmediatelysound.The
alarmwillcontinuetosoundfor30seconds,thenstopandautomaticallyre-arm
thevehicle.Ifthepotentialthiefleftadooropened,thealarmwillsoundforfivemore
30 second cycles, then re - arm and ignore the opened door zone.
2. Wheneverthesystemisarmed,thereddashmountedL.E.D.indicatorwillslowly
flash.Thisservesasavisualdeterrenttothepotentialthief.TheL.E.D.isavery
lowcurrentbulb,andwillnotcausethevehicle’sbatterytodrain,evenwhenthe
vehicleisleftunattendedforextendedperiods.
3. Wheneverthesystemistriggered,thevehicle’sparkinglightswillflashforthe30
secondalarmcycle,attractingaddedvisualattentiontothevehicle.
4. Wheneverthesystemisarmed,thevehicle’sstarterwillbedisabled.Thevehicle
willnotstart.
DISARMING THE SYSTEM :
1. Asyouapproachthevehicle,pressandreleasetheunlockbuttononthekeychain
transmitter.
2. Thesirenandorhornwillbeeptwotimes,theparkinglampswillflashtwotimes,
and the red dash mounted L.E.D. will turn off, indicating that the system is
DISARMED. Iftheoptionalentryilluminationfeaturehasbeeninstalled,the
vehicle’sinteriorlightswillturnonfor30seconds,oruntiltheignitionkeyisturnedon.
NOTE: Ifyoursystemhasbeenprogrammedfor“passivearming“,thenitwill
begin to re-arm immediately after disarming. This is indicated by a
Page2

rapid flashing of the red dash mounted L.E.D. Opening one of the
vehicle’sdoorswillsuspendthepassivearmingprocessuntilalldoors
have been closed, or until the ignition key has been turned on.
INTRUSIONWARNING SIGNALS :
Thesystemwillinformyouifanintrusionattempthasoccurredwhileyouwereaway
fromthevehicle.Ifanintrusionattempthasoccurred,thesirenandorhornwillbeep
four times when the system is disarmed. The vehicle’s parking lights will also flash
threetimesto indicate an intrusion has occurred.
Enterthe vehicleandobservethedashmountedL.E.D.forfurtherinformation.
1. IftheL.E.D.isflashingonetime...pause...onetime...pause...etc.,thenanintrusion
attemptwasmadetoavoltagesensing,lightactivatedentrypoint,ortoanoptional
sensor that has been connected to zone 1.
2. IftheL.E.D.isflashingtwotimes...pause...twotimes...pause...etc.,thenan
intrusionattemptwasmadetothehoodortrunk,ortoanoptionalsensorthathas
beenconnectedtozone 2.
3. IftheL.E.D.isflashingthreetimes...pause...threetimes...pause...etc.,thenan
intrusionattemptwasmade through oneofthevehicle’sdoors.
Theseintrusionwarningindicatorsarestored in the system’s memory, andwillonly
beerasedwhentheignitionkeyisturnedtothe“on“position.
OPERATING THE EMERGENCY PANIC:
The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch;
1. Presstheunlock,thenlock,thenunlockbuttonsonyourkeychaintransmitterwithin
3seconds. Thealarmwillimmediatelysound,andcontinuetosoundfor30seconds.
2. Tostopthealarmbeforethe30secondcycle hasexpired,simply pressand
releasetheunlockbuttononyourkeychaintransmitter.
USING THE VALET SWITCH :
Thevaletswitchallowsyou to temporarily bypass all alarmfunctions,eliminatingthe
needtohandyourtransmittertoparking attendants or garage mechanics. When the
systemisinvaletmode, all alarm functions arebypassed,howevertheremotepanic
feature and remote door locks will remain operational. To use the valet mode, the
system must first be disarmed either by using your keychain transmitter, or by
activating yourpersonalizedmanualoverridecode.
TO ENTER THE VALET MODE:
1. Disarmtheunitbyuseofthefactorytransmitterorbyuseofthemanualoverride
sequence.
Page3

2. Turntheignitionswitch to the “On”position.
3. Pressandholdthevalet/override pushbutton switch for 5 seconds. The L.E.D.
turnson,indicatingvaletmodehas beensuccessfullyentered.
TO EXIT VALET:
With the ignition switch in the on position, press and release the valet/override
pushbutton switch one time. The L.E.D. turns off indicating the valet mode has
successfullybeenexited.
MANUALOVERRIDEOPERATION:
If your factory transmitter is lost, broken, or otherwise rendered inoperable, your
system can be overridden allowing operation of the vehicle. The manual override
code is pre-programmed at the factory to 11. This code can be changed by the
operatorto a more familiar two digit number. Once you’ve become familiar with the
system’s operation and override procedure, we suggest you change the code for
addedsecurity.
NOTE: The override procedure below describes use, assuming that the factory
pre-set code has not been changed and is still settothefactorydefault 11.
Thevalet/overridepush button switch is used to enter the tenths andunits
digits, pressing and releasing this button one time for each digit required.
To manually override your system, with a code of 11, follow the sequence listed
below:
1. TheL.E.D.isflashingindicatingunitisarmed,enterthevehicle,thesirenwillsound,
turntheignitionswitchtothe“on”position.
2. Within10secondsbegin to enter tenths digit of override code.
(Inthisexamplethecodeis11,sopress andreleasetheValet/Overridepushbutton
onetime).
3. Within10secondsof entering the last tenths digit, turn ignition “off then on”.
4. Within 10 seconds of turning the ignition switch on, begin to enter unitsdigit of
override code. (In this example the code is 11, so press and release the
Valet/Override pushbuttononetime).
5. Within5 seconds after the lastunits digit is entered, turn the ignition switch off,
thenon,andstartyourvehicle.
If the manual override code is entered properly, the unit stops sounding, the L.E.D.
turnsoff,indicatingasuccessful override. The system is now disarmedandyoucan
start and operate your vehicle. The unit will allow three attempts to disarm via the
manual override sequence. If the code is not successfully entered within the three
attempts,disarmingwith the manual override switch will be locked for 10minutes.
Inmanycases,toincreasethesecurityofyoursystem,youmayelecttochangethe
manual override code to a number that is more familiar to you, or simply to have a
Page4

differentcode than was pre-assignedfromthe factory. ToChange the pre-assigned
overridecodefollowthestepsoutlinedbelow.
Itisadvisedyoureadbothsectionsundertheheadings “Programming Your Custom
OverrideCode”and,“CustomCodeProgrammingExample”,Tocompletelyunderstand
theprocedurebeforebeginning:
Programming Your Custom Override Code:
Unlike override switches easily found, and defeated, the PRO-9232 allows the
consumer to program a personal override code, offering a higher level of security.
Thesystem comesfrom the factory with a pre-programmed override code of11. To
changethisdefaultoverridecode,dothefollowing:
1. Disarmthe systembyuseofthetransmitter, or by use of theemergencyoverride
sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3 times.
3. Within10 seconds turn the ignition switch off, on, off, on, off,on.
(Thesirenor horn will beep and the lights will flash onetime.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
5. Within10secondsof thelastentered10thsdigit,turntheignition switchoffthenon.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and
releasing thepushbutton switch from 1 up to 9 times.
7. Finishbyturningtheignitionswitchtotheoffposition.
If the new code was accepted, the unit will report back the newly entered code, by
flashingtheL.E.D.,firstindicatingthe10thsdigit,pauseandthenthe units digit. The
unit will report the new code three times with a one second pause between each
code, then the system will begin arming. If the L.E.D. flash pattern reports the
previously storedcode, the newcodewasnotentered correctly. Pleaserepeatsteps
1through7aboveconsideringthe following.
NOTE: Acceptabledigits10thsor units are1through9. Theunit will not recognizea
0(Zero),ornodigitenteredinanyplace, units or tenths.
NOTE: If15secondsof inactivity expire, oriftheignitionswitchis turned off formore
then5secondsduringanyoftheabovesteps,theunitwillrevertbacktothe
last successfully stored code.
Custom Code Programming Example:
ToChangethe code fromthefactorypre-assignedcode of11to“52” you woulddothe
following:
1. Disarmthe systembyuseofthetransmitter, or by use of theemergencyoverride
sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3 times.
Page5

4. Within10 seconds turn the ignitionswitch off, on, off, on, off, on.
(Thesirenor horn will beep and the lights will flashonetime.)
5. Within 10 seconds, begin to press and release the push button switch to set the
tenthsdigit.
(As per the example, press and release 5 times to set the tenths digit to 5)
6. Within10secondsofthelastpressofthepush-button,turn the ignition switch off
thenon.
7. Within 10 seconds, begin to press and release the push button switch to set the
unitsdigit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch tothe offposition. Immediately observe the L.E.D. flash
pattern.
You will note the L.E.D. flashing five times, pause, and then flash two times, pause.
This pattern will be repeated three times indicating the new code (52) has been
accepted and stored inmemory.
NOTE: Ifafterstep 7, theL.E.D.flashesacode other thanwhatwasjustentered, this
indicatesthatthecodehasnotbeenchanged. Youwillhavetorepeatsteps
1through7abovebeingcertaintonotethe following:
Acceptabledigits10thsor units are 1through9. Theunitwill not recognize a0(Zero),
ornodigitenteredinany place, units or tenths.
NOTE: If15secondsofinactivityexpire, or if the ignition switch isturnedoffformore
then5secondsduringanyof the above steps, the unit will revert back to the
last successfully stored code.
ADDITIONAL REMOTE FUNCTION :
Thissystemallows the control of any one of the followingoptionalaccessories;
RemoteCar Starter
Remote Window Closure
Remote Window Open
Tooperatetheoptionalaccessory;
1. Pressthelock,thenunlock,thenlockbuttonsonyourkeychaintransmitterwithin
3 seconds.
2. Theoptionalaccessorywillimmediatelyactivate.
OPTIONAL AUTO LOCK/UNLOCK FEATURE :
Ifyourexistingfactoryinstalledkeylessentrysystemdidnotincludetheautomaticdoor
lockandunlockfeature,thenthisfeaturecanbeactivatedfromthePRO9232upgrade
module. Whenthis accessory has been added, any time theignition key is turned to
the on position
and all vehicle doors are closed, the doors will lock in 4 seconds.
Additionally,anytimetheignitionkeyisturnedtotheoffposition,thedoorswillunlock.
Page6

ELIMINATING THE ARM / DISARM CHIRPS :
Thenormalarminganddisarmingconfirmationchirpscaneasilybeturnedoffusingthe
valetpushbuttonswitch. To dothis;
1.Turntheignitionkeyon,andthenoff.
2. Within10secondsofturningtheignitionkeyoff,pressandreleasethe valet switch
3 times.
3. a. If,beforeproceedingwithstep1,thechirpswereon,thenyouwillhear2chirps
toindicatethatthechirps havebeenturned off.
b. If,beforeproceedingwithstep1,thechirpswere off, then you will hear 1 chirp
toindicatethatthechirps havebeenturned on.
4. Wheneverpowertothesystemhasbeendisconnected(forrepairorservicetothe
vehicle),thechirpswillbeactivatedwhenthepowerisre-connected.Toturnthe
chirpsoff,simply execute steps 1 through 3 above.
NOTE : Whenever the Arm/Disarm chirps are by-passed, the 3 chirp defective
zoneandthe4chirpintrusionindicatorwillalwaysoperate.Thisfeature
willalwayswarnyouifadoorwasleftajarwhenarming,orthevehiclewas
tampered with in your absence.
Page7

PRO 9232
SYSTEM FUNCTIONS AT A GLANCE
PASSIVE ARMING
ARMED
DISARMED
VALET MODE
INTRUSION ZONE 3
INTRUSION ZONE 2
INTRUSION ZONE 1
ARM
DISARM
ARM / DOOR OPEN
10 MIN. PASSIVE ARM / DOOR OPEN
DISARM / INTRUSION
DISARM / AFTER 10 MIN.
PASSIVE ARM
DISARM / AFTER 10 MIN.
PASSIVE ARM AND INTRUSION
ARM
DISARM
DISARM / INTRUSION
DASH L.E.D. INDICATORS
RAPID FLASHING ..........................................................
SLOW FLASHING ...........................................................................
OFF ...........................................................................................
ON - SOLID ............................................................................
3 FLASH ... PAUSE .....................................................
2 FLASH ... PAUSE .....................................................
1 FLASH ... PAUSE .....................................................
CHIRP INDICATORS
1 CHIRP * ............................................................................................
2 CHIRPS* .....................................................................................
3 CHIRPS ...................................................................
3 CHIRPS .......................................
4 CHIRPS .................................................................
2 SHORT CHIRPS - 1 LONG CHIRP.....................
4 SHORT CHIRPS - 1 LONG ................................
* These chirps are optional, and can be de-activated.
PARKING LAMPS
1 FLASH ..................................................................................................
2 FLASH .........................................................................................
3 FLASH ...................................................................
Your System Has These Features Activated:
Starter Disable When Armed
Passive Arming
Instant Trigger
Remote Car Starter
Remote Window Open
q
q
q
q
q
q
q
q
q
q
Form No. 128-5407
© 1998 Audiovox Corp. 150 Marcus Blvd. Hauppauge, N.Y. 11788
Remote Window Closure
Key Activated Auto Lock/Unlock
Shock Detector
Motion Detector
Hardwire