Baudisch Compact Classic AHD User manual

COMPACTCLASSIC AHD
QUICKSTART

COMPACTCLASSIC AHD
QUICKSTART
hardware version
1.9
software version:
V8.6 / V3.6 2 / 4
This document about Compact Classic AHD (Item Nr.: 33-1535) can be downloaded
from our website:http://www.baudisch.com/downloads
1. Overview
Camera
SIP Module
Power Supply 24 V / DC
0V and +UB
Relay 1 / Relay 2
normally open
LAN / PoE
Call Button
Microphone

COMPACTCLASSIC AHD
QUICKSTART
hardware version
1.9
software version:
V8.6 / V3.6 3 / 4
2. Power
Power over Ethernet (PoE)
•PoE Switch
The CompactClassic AHD can be supplied by a network switch with PoE support. The
connection takes place via the free RJ45 LAN port on the SIP Module [Input].
•PoE Injektor
The CompactClassic AHD can be supplied by a PoE Injector. The connection takes place via
the free RJ45 LAN port on the SIP Module [Input].
24 V / DC (alternative)
Alternatively, the SIP Module can be supplied by using a separate 24 V / DC, 1 A power adapter.
The connection is made via the screw terminal at 0V and +UB (see picture).
3. Configuration
SIP Module
•IP address: 192.168.1.200
•Netmask: 255.255.0.0
•Password: 1234
Setting the IP address
•Open the web interface of the SIP Module in a web browser via IP address.
oDefault IP address: 192.168.1.200
•Navigate to [Quickstart] -> [Network] (password: 1234).
•Enter your [Network settings]:
oIP address
oSubnet mask
oGateway
•Confirm your entries with [Save](the SIP Module will restart).
Setting up SIP account
•Open the web interface of the SIP Module via a web browser via IP address.
•Navigate to the [SIP] (password: 1234).
•Enter your [SIP settings]:
oSIP registration: [Yes](for operation with a SIP server) [No](for direct IP connection)
oSIP server: (IP address of the SIP server / phone system)
oSIP user ID: (SIP account login for the SIP Module)
oSIP authentication PIN: (SIP account password for the SIP Module).
oDisplay name:(optional name for the SIP Module)
•Confirm your entries with [Save] (the SIP Module will restart).

COMPACTCLASSIC AHD
QUICKSTART
hardware version
1.9
software version:
V8.6 / V3.6 4 / 4
Configuration Central Call Button and door opening
•Open the web interface of the SIP Module via a web browser via IP address.
•Navigate to the [Setup] (password: 1234).
oSelect [Centrall Call Module]: Yes
•Navigate to [Call destinations] (password: 1234).
•Enter the target for the Central Call Button identical to [Switchboard call]:
oName: (a name must be entered)
oNumber: (destination number or IP address for direct IP connection)
oDTMF code: (code to trigger the door relay e. g. „0 - - -“)
oIncoming: (response to incoming call from this number)
•Confirm your entries with [Save](the SIP Module will restart).
Camera
•IP Address: 192.168.1.220
•Netmask: 255.255.0.0
•Username: admin
•Password: 1234
Setting the IP address
•Open the web interface of the IP camera in a web browser via IP address.
oDefault IP address: 192.168.1.220
•Navigate to the [Configuration] (username: admin, password: 1234).
•Go to the menu [General]
•Enter your IPv4 address configuration - Ethernet:
oIP address
oSubnet mask
oGateway
•Confirm your entries with [Save].
Display camera image or video stream
You have the following options to access the camera directly.
•To display individual JPG pictures, use the following URL:
ohttp://*username*:*password*@*Camera-IP*/jpg/image.jpg
oWith factory settings e. g.: http://admin:1234@192.168.1.220/jpg/image.jpg
•To display a Motion-JPEG stream, use the following URL:
ohttp://*username*:*password*@*Camera-IP*/mjpg/video.mjpg
oWith factory settings e. g.: http://admin:1234@192.168.1.220/mjpg/video.mjpg
4. Support
For support please send an email to supp[email protected]
or contact our support hotline [phone]