Bauknecht BIVMS 8100 Operating instructions

Benutzer- und Wartungshandbuch
User and maintenance manual
Manuel d’utilisation et d’entretien
Handleiding voor gebruik en onderhoud
Manuale d’uso e manutenzione
EN
IT
BIVMS 8100

EN32
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
All safety warnings give specific details of the potential risk present and
indicate how to reduce risk of injury, damage and electric shock
resulting from improper use of the appliance. Carefully observe the
following instructions:
- The appliance must be disconnected from the power supply before
carrying out any installation work.
- Installation and maintenance must be carried out by a qualified
technician, in compliance with the manufacturer’s instructions and
local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Power cable replacement must be carried out by a qualified
electrician. Contact an authorized service centre.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the
appliance, once fitted in its housing, to the main power supply.
- For installation to comply with current safety regulations, an all-
pole disconnect switch with minimum contact gap of 3 mm must
be utilized.
- Do not use multiple plug adaptors if the oven is fitted with a plug.
- Do not use extension leads.
- Do not pull the power supply cable.
- The electrical components must not be accessible to the user after
installation.
- If the surface of the induction plate is cracked, do not use it and
switch off the appliance to avoid the possibility of electric shock
(only for models with induction function).
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could cause serious injury.

EN33
- Do not touch the appliance with any wet part of the body and do
not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for
cooking food. No other type of use is permitted (e.g.: heating
rooms). The Manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
- This appliance can be used by children from 8 years and above and
persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand hazards involved. Children shall not play with
the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
- The accessible parts of the appliance may become very hot during
use. Young children should be kept away from the appliance and
supervised to ensure that they do not play with it.
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Children less
than 8 years old shall be kept away, unless continuously supervised.
- During and after use, do not touch the heating elements or interior
surfaces of the appliance - risk of burns. Do not allow the appliance
to come into contact with cloths or other flammable materials until
all the components have cooled sufficiently.
- At the end of cooking, exercise caution when opening the
appliance door, letting the hot air or steam exit gradually before
accessing the oven. When the appliance door is shut, hot air is
vented from the aperture above the control panel. Do not obstruct
the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to
touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire
may break out if the appliance is inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance.
The pressure that builds up inside might cause the jar to explode,
damaging the appliance.
- Do not use containers made of synthetic materials.

EN34
- Overheated oils and fats catch fire easily. Always remain vigilant
when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum,
cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released by the
alcohol may catch fire upon coming into contact with the electrical
heating element.
- Never use steam cleaning equipment.
- Do not touch the oven during the pyrolysis cycle. Keep children
away from the oven during the pyrolysis cycle. Excess spillage must
be removed from the oven cavity before cleaning cycle (only for
ovens with Pyrolysis function).
- Only use the temperature probe recommended for this oven.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean
the oven door glass since they can scratch the surface, which may
result in shattering of the glass.
- Ensure that the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
- Do not use aluminium foil to cover food in the cooking vessel
(only for ovens with cooking vessel supplied).
- Use protective gloves to perform all unpacking and installation
operations.
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
To safely move the oven, use the handle provided in the accessories pack.
1. Insert the handle securely into the lateral holes (Fig. 1).
2. Lift the handle up as shown in Fig. 2
INSTALLATION
Fig. 1 Fig. 2

EN35
PREPARING THE HOUSING UNIT
• Kitchen units in contact with the oven must be heat resistant (min 90°C).
• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
• After installation, the bottom of the oven must no longer be accessible.
• For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION (only in some models)
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
• Power cable replacement (type H05 RR-F 3 x 1.5 mm2) must be carried out by a qualified electrician. Contact an
authorized service centre.
• The oven is programmed to operate with power absorption above 2.5 kW (indicated by "HIGH" in the settings) which is
compatible with a domestic power supply above 3kW. If the household has a lower power supply, the setting must be
lowered ("LOW" in the settings). The table below details the recommended electrical power settings for the various
countries.
GENERAL RECOMMENDATIONS
Before use:
- Remove protective cardboard pieces, protective film and adhesive labels from accessories, induction plate and cooking
vessel.
- Remove the accessories from the oven. Position the induction plate at the third level and plug it in. Place the cooking
vessel on the induction plate and fill it in with 200g of water. Select the Top Finishing function and run the oven for
approximately one hour to eliminate the smell and fumes from the insulating materials and protective grease.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Never pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
- Do not expose the oven to atmospheric agents.
- Never pour water on the induction plate when inserted into the oven or when it is hot; this could damage the glass or the
enamel coating.
- Insert and remove the induction plate carefully in order to avoid accidental damage to the glass and/or electrical plug.
- Before using the oven in standard mode (without induction), completely remove the induction plate from the oven.
Leaving the induction plate in the oven could damage it.
After Use:
- Allow the induction plate to cool down before removal if cleaning is required. When the induction plate is removed from
the oven, ensure the supplied socket cover is used to prevent dirt entering the electrical socket (Fig. 1).
Country Setting
Germany High
Spain Low
Finland High
France High
Italy Low
Holland High
Norway High
Sweden High
UK Low
Belgium High
Fig. 1

EN36
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/CE.
The oven does not work:
• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
• Turn off the oven and restart it to see if the fault persists.
The door will not open:
• Turn off the oven and restart it to see if the fault persists.
•Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see paragraph “Cleaning
cycle of ovens with pyrolysis function”).
The electronic programmer does not work:
• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the
number that follows the letter “ ”.
The induction plate does not work:
• The induction plate must be used on the third shelf position only; ensure it is correctly positioned and fully connected.
• Turn the oven off and then on again. Check if the fault persists.
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
• a brief description of the fault;
• the type and exact model of the oven;
• the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
SAFEGUARDING THE ENVIRONMENT
DECLARATION OF CONFORMITY
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE

EN37
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp Microfibre cloth.
• Clean the surfaces with a damp Microfibre cloth. If it is very dirty, add a few drops of washing up detergent to the water.
Finish off with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
• Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still hot.
• Food residues can be easily removed using a brush or sponge.
Induction Plate:
• When cool to the touch, use a sponge and suitable liquid detergent for ovens or hobs. Do not clean the induction plate in
a dishwasher.
Internal Electrical Socket:
• Remove the metallic plug cover; use a humidified sponge to clean the plug. Do not use metallic and/or sharp tools.
Cooking Vessel:
• Suitable for dishwashing. Alternatively, use soft sponge and suitable liquid detergent.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
• Operate the oven empty with the fan-assisted function at 200°C for about one hour
• Next, leave the appliance to cool down before removing any food residue with a sponge.
CLEANING
WARNING - Never use steam cleaning equipment.
- Only clean the oven when it is cool to the touch.
- Disconnect the appliance from the power supply.

EN38
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (Fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
REMOVING THE SIDE GRILLES
The accessory-holder grilles are equipped with two fixing screws (Fig. 3) for optimum stability.
1. Remove the screws and fixing plates on the right and left with the aid of a coin or tool.
2. To remove the grilles, lift them up (1) and turn them (2) as shown in Fig. 5.
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles (Fig. 6).
2. Pull the heating element out a little (Fig. 7) and lower it (Fig. 8).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 9), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present (Fig. 6).
3. Use a screwdriver to prise off the lamp cover (Fig. 10).
MAINTENANCE
WARNING - Use protective gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the appliance from the power supply.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
Fig. 6 Fig. 7 Fig. 8

EN39
4. Replace the lamp (see note for lamp type) (Fig. 11).
5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 12).
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B.:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room
illumination (Commission Regulation (EC) No 244/2009).
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 9 Fig. 10 Fig. 11 Fig. 12

EN40
FOR THE ELECTRICAL CONNECTION, SEE THE SECTION ON INSTALLATION
The induction oven is equipped with an electrical socket on the rear wall of the oven to supply power to
the heating element inside the induction plate when plugged in.
The induction plate is designed to work together with the induction cooking vessel supplied with the oven.
Improved cooking performances and energy consumption can be achieved by using the cooking vessel
and induction plate.
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Lamps
6. Circular heating element (not visible)
7. Fan
8. Lower heating element (not visible)
9. Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
12. Electrical socket (inside oven)
13. Induction Plate
14. Induction Plate position
N.B.:
- During cooking, the cooling fan may switch on intermittently in order to reduce energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
ACCESSORIES SUPPLIED
A. WIRE SHELF (1): the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. DRIP-TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or
as an oven tray for cooking meat, fish, vegetables, facaccia, etc.
C. BAKING TRAY (1): use for bakery and pastry products, but also roasts, fish en papillotte, etc.
D. COOKING VESSEL (1): the cooking vessel is designed to be used with the induction plate and should
be placed according to the position markings on the induction plate glass.
E. INDUCTION PLATE: to be used in induction mode only by placing it on the third shelf position and
ensuring the electrical plug is fully inserted (refer to “Inserting wire shelves and other accessories in
the oven”).
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B Fig. C Fig. D Fig. E

EN41
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSERTING RACKS AND OTHER ACCESSORIES IN THE OVEN
The rack and other accessories have a locking system to prevent their inadvertent removal.
1. Insert the rack horizontally, with the raised part “A” upwards (Fig. 1).
2. Tilt the rack when it reaches the locking position “B” (Fig. 2).
3. Return the rack to the horizontal position and push it in fully “C” (Fig. 3).
4. To remove the rack, proceed in reverse order.
The other accessories, such as the drip-tray and baking tray, are inserted in exactly the same way. The
protrusion on the flat part enables locking.
INDUCTION PLATE:
The Induction plate must be inserted at the third shelf position to allow the electrical plug to engage.
1. Use both hands to properly place the induction plate on the third shelf position (Fig. 1).
2. Use both hands to push the induction plate up to the electrical plug (Fig. 2).
3. Ensure the plug is fully engaged by firmly pushing the induction tray (Fig. 3).
COOKING VESSEL:
Place the cooking vessel on the induction plate, ensuring that the bottom of the vessel lays within the
rectangular markings on induction plate glass.
1. Use both hands to place the cooking vessel on the induction plate (Fig. 4).
2. Place the cooking vessel at the centre of the markings on the glass (Fig. 5).
Fig. 1
Fig. 2 Fig. 3
Fig. 1 Fig. 2 Fig. 3
Fig. 4 Fig. 5

EN42
REMOVAL OF THE COOKING VESSEL AND INDUCTION PLATE
REMOVING THE COOKING VESSEL:
IMPORTANT: The induction cooking vessel can become extremely hot. Always use oven gloves to touch
and move it.
1. Using both hands, grasp the front handle and partially remove the cooking vessel (Fig. 1).
2. Then use the lateral handles to better grasp and fully remove the cooking vessel (Fig. 2).
REMOVING THE INDUCTION PLATE:
IMPORTANT: To ensure a good electrical connection, the induction plate will be securely inserted and will
require some slight additional force to be disengaged. Do not remove the induction plate when the
cooking vessel or any other accessory is present.
Always use oven gloves when induction plate and/or oven are hot.
1. With both hands, grasp the induction plate and remove it. Some slight force will be needed to
disengage the plate from the socket (Fig. 3).
2. With both hands, remove the induction plate and store it away, carefully avoiding impacts that could
damage the glass or electrical plug (Fig. 4).
DESCRIPTION OF CONTROL PANEL
ELECTRONIC PROGRAMMER
1. FUNCTIONS KNOB: On/Off and function selection
2. BROWSE KNOB: for browsing the menu and adjusting preset values
N.B.:The two knobs are retractable. Press the knobs in the middle and they pop up.
3. BUTTON : to return to the previous screen or save the preferred function
4. BUTTON : to select and confirm settings
LIST OF FUNCTIONS
Turn the “Functions” knob to any position and the oven switches on. The display will show the following
indication:
Press any key to skip the message and the display will show the functions or the associated submenus.
Fig. 1 Fig. 2
Fig. 3 Fig. 4
1 23 4
DISPLAY
Specials: For defrosting food
Keep Warm
Frozen Food
Defrosting

EN43
NOTE: The induction first alert can be disabled/enabled through the Settings Menu. If the induction plate
is already properly engaged, when oven is switch on, the induction first alert will not be shown.
The submenus are available and selectable by turning the knob to the functions INDUCTION, GRILL,
SPECIALS, SETTINGS and RECIPES.
A. Icon for highlighted function
B. The highlighted function can be selected by pressing
C. Description of highlighted function
D. Other available and selectable functions.
FUNCTION DETAILS
After selecting the desired function, the display will show further options and related details.
To move between the different zones, turn the “Browse” knob: the cursor goes next to the values
modifiable by following the order described above. Press the button to select the value, change it by
turning the “Browse” knob and confirm with the button .
NOTE: In induction mode only Zone 4 and Zone 5 can be adjusted.
USING THE APPLIANCE FOR THE FIRST TIME - LANGUAGE SELECTION AND SETTING
THE TIME
For correct use of the oven, when switched on for the first time it is necessary to select the desired language
and set the correct time.
Proceed as follows:
1. Turn the “Functions” knob to any position: the display will show the list of the first three available
languages.
2. Turn the “Browse” knob to scroll the list.
3. When the desired language is highlighted, press to select it.
After selecting the language, the display will show 12:00 flashing.
4. Set the time by turning the “Browse” knob.
5. Confirm the setting by pressing .
SELECTING COOKING FUNCTIONS
1. If the oven is off, turn the “Functions” knob; the display will show the cooking functions or related submenus.
N.B.:For the list and description of functions, see the specific table on page48 and page49.
If the induction plate is already properly engaged or whenever the induction plate is inserted,
only Induction Functions and Settings will be accessible through the main menu.
If knob is not set on Induction Functions the display will show the message “Please select the
induction mode”.
If the induction plate is not engaged into the oven, both standard functions MENU and
induction functions MENU will be accessible.
When the induction plate is inserted or removed, a message indicating correct engagement/
disengagement will be shown on the display.
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost
A
D
C
B
Zone 3Zone 4
Zone 5
Zone 2
Zone 1Cursor
PREHEAT
Yes
TEMPERATURE
180°C
COOKTIME
ENDTIME
Convection Bake --:--
--:--
Start
PREHEAT
yes
TEMPERATURE
180°C
COOKTIME
ENDTIME
Convection Bake --:--
--:--
Start PREHEAT
Yes
TEMPERATURE
180°C
COOKTIME
ENDTIME
Convection Bake --:--
--:--
Start

EN44
2. Inside the submenu, browse the various options available by turning the “Browse” knob: the chosen
function is highlighted in white in the middle of the screen. To select it, press the button .
3. The cooking settings appear on the display. If the preselected values are those desired, turn the
“Browse” knob to position the cursor at “Start”, then press the button ; otherwise, proceed as
indicated below to modify them.
SETTING THE TEMPERATURE/GRILL POWER (Standard Functions only)
To change the temperature or grill power, proceed as follows:
1. Make sure the cursor is positioned next to the temperature value (zone 1); press the button to
select the parameter to be modified: the temperature values flash.
2. Set the desired value by turning the “Browse” knob and press the button to confirm.
3. Turn the “Browse” knob to position the cursor at “Start”, then press the button .
4. The display indicates which level food should be placed on. Carry out the operation and press the
button to start cooking.
The set temperature can be changed even during cooking by following the same procedure.
5. At the end of cooking, the cooking end message appears. The oven can now be switched off by
turning the “Functions” knob to 0 (zero), or cooking can be prolonged by turning the “Browse” knob
clockwise. When switched off, the display shows the cooling bar which indicates the temperature
inside the oven.
PREHEATING THE OVEN (Standard Functions only)
To preheat the oven before placing food in it, the preselection must be modified as follows:
1. Turn the “Browse” knob to position the cursor at preheating.
2. Press the button to select the parameter: the message “No” flashes.
3. Modify the parameter by turning the “Browse” knob: “Yes” appears on the display.
4. Confirm the choice by pressing the button .
FAST PREHEATING (Standard Functions only)
To preheat the oven quickly, proceed as follows:
1. Turn the “Functions” knob to select the fast preheating function.
2. Confirm by pressing the button : the settings appear on the display.
3. If the proposed temperature is that desired, turn the “Browse” knob to position the cursor at “Start”, then
press the button . To modify it, proceed as described in the previous sections. An acoustic signal will
sound when the oven has reached the set temperature. At the end of preheating, the oven automatically
selects the conventional function .
The food can now be placed in the oven for cooking.
4. To set a different cooking function, turn the “Functions” knob and select the required function.
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional
--:--
--:--
Start
PREHEAT
No
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional --:--
--:--
Start PREHEAT
No
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional --:--
--:--
Start
PREHEAT
Yes
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional --:--
--:--
Start PREHEAT
Yes
TEMPERATURE
200°C
COOKTIME
ENDTIME
Conventional --:--
--:--
Start
TEMPERATURE
180°C
Turn +/- to adjust ...
Start
Specials: For defrosting food
Warm Keeping
Frozen Food
Defrost

EN45
SETTING THE COOKING DURATION
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1. To select the function, turn the “Browse” knob to position the cursor at “cooking duration”.
2. Press the button to select the parameter; “00:00” flashes on the display.
3. Modify the value by turning the “Browse” knob to display the desired cooking time.
4. Confirm the selected value by pressing the button .
BROWNING (Standard Functions only)
At the end of cooking, with certain functions, the display indicates the possibility of browning the surface of
your dish. This function can only be used when a cooking duration has been set.
At the end of cooking time, the display shows “^ to prolong, OK to brown”. Press the button , and the
oven starts a 5 minute browning cycle. This function can only be carried out once.
SETTING COOKING END TIME / DELAYED START
The desired cooking end time can be set, delaying oven switch-on by up to a maximum of 23 hours and
59 minutes, starting from the current time. This is possible only after a cooking duration has been set. This
setting is available only if preheating is not required for the selected function.
After setting the cooking duration, the display shows the cooking end time (for example 19:20). To delay
the end of cooking, postponing oven switch-on, proceed as follows:
1. Turn the “Browse” knob to position the cursor at the cooking end time.
2. Press the button to select the parameter: the cooking end time flashes.
3. To delay the cooking end time, turn the “Browse” knob to the desired value.
4. Confirm the selected value by pressing the button .
5. Turn the “Browse” knob to position the cursor at START, then press the button .
6. The display indicates which level food should be placed on. Carry out the operation and press the
button to start cooking. The oven will start cooking after a period of time calculated so as to
finish cooking at the set time (e.g. for food requiring a cooking time of 20 minutes, if the cooking end
time is set to 20:10 the oven will start cooking at 19:50).
N.B.:During the waiting stage, the cooking cycle can be started in any case by turning the “Browse”
knob to position the cursor at “Start” and then pressing the button .
The set values (temperature, grill level, cooking time) can be changed at any time, as described in
previous sections.
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional --:--
--:--
Start
PREHEAT
No
TEMPERATURE
180°C
HH:MM
ENDTIME
Conventional 19:01
00:01
Start
PREHEAT
No
TEMPERATURE
180°C
HH:MM
ENDTIME
Conventional 19:01
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 19:20
- 00:30
Start
Browning
COOK TIME
END TIME
20:05
- 00:05
Cooking nished at 20:00
^ to prolong, OK to brown
Browning nished at 20:05
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 19:20
- 00:30
Start PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 19:20
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 20:10
- 00:30
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 20:10
- 00:29
Start
PREHEAT
No
TEMPERATURE
180°C
COOKTIME
ENDTIME
Conventional 20:10
- 00:30
Start

EN46
TIMER
This function can be used only with the oven switched off and is useful, for example, for controlling the
cooking time of pasta. The maximum time which can be set is 1 hour 30 minutes.
1. With the oven switched off, press the button : “00:00:00” will appear on the display.
2. Turn the “Browse” knob to select the desired time.
3. Press the button to start the countdown. When the set time has elapsed, “00:00:00” will appear
on the display and an acoustic signal sounds. The time can now be prolonged, proceeding as
described above, or the timer can be deactivated by pressing the button (the current time will
appear on the display).
RECIPES
Thanks to “Intelligent Sensor Technology”, it is possible to use 30 preset recipes with the ideal cooking
function and temperature.
It is necessary to follow the recipe-book provided only regarding ingredients and preparation of the dish.
Then, proceed as follows:
1. Select “RECIPES” by turning the “Functions” knob.
2. Select the dish to be cooked from those proposed.
3. Confirm the selected dish with the button .
4. Select the desired recipe by turning the “Browse” knob.
5. Confirm by pressing the button : the display shows the approximate cooking time.
6. Place the dish in the oven and turn the “Browse” knob to position the cursor at “Start”, then press the
button .
7. The display indicates which level food should be placed on. Carry out the operation and press the
button to start cooking. To delay cooking, see the relevant section.
N.B.:Some dishes must be turned or stirred half way through cooking: an acoustic signal sounds and
the display shows the type of operation required.
The cooking time initially shown is only approximate: it can be prolonged automatically during
cooking.
Shortly before cooking time ends, the oven prompts you to check that the food is cooked as desired. If it is
not, the cooking time can be prolonged manually by turning the “Browse” knob.
Turn +/- to set Timer, ✓to Start
00 : 00 : 00
(HH) (MM) (SS)
Turn +/- to set Timer, ✓to Start
00 : 30 : 00
(HH) (MM) (SS)
Timer
01 : 09 : 00
Fully automatic Recipes
Traditional
Settings
Recipes
Fully automatic Recipes
Vegetables
Fish
Poultry
Recipes: See cookbook for description
Chicken Breasts
Roast Chicken
CONTROL
Automatic
COOK TIME
END TIME
Roast Chicken 19:45
- 00:45
CONTROL
Automatic
COOK TIME
END TIME
Cooking 19:45
- 00:44
Insert food on Level 3
Press when done
Please turn food
Cooking nearly nished
Please check on food
Cooking Finished at 19:45
Press to Prolong Cooking

EN47
INDUCTION FUNCTIONS
Thanks to the Induction Heating technology, the oven offers several cooking functions (see Function
Description table) which guarantee high cooking performances together with a very fast cooking process
and low energy consumption.
In order to ensure optimum performance, use the induction plate in combination with the supplied
stainless steel cooking vessel (see Inserting Wire Shelves and Other Accessories in the Oven for
information on how to insert both the induction plate and the cooking vessel).
To start the Induction functions etc. navigate the main menu (refer to Selecting Cooking Functions or
press the induction direct access icon).
To access the induction functions on the user interface, the induction plate must be properly inserted into
the oven.
If an induction cooking cycle is required but the induction plate or cooking vessel are not inserted, the
appliance will detect the absence of one or both and will advise that they be inserted before proceeding:
1. Turn the function knob to Induction Functions
2. Select the food category to be cooked with the browse knob from the proposed list and confirm
using OK.
3. According to food category, further subcategory and/or food weight may be selected by turning the
browse knob and confirm with OK.
4. Press button OK to confirm.
5. Place the food in the oven and press OK.
6th Sense Induction Functions
Some cooking functions (Roasted Meat, Roasted Poultry and Fish) are 6th sense assisted. Given the weight
of food to be prepared, 6th sense technology cooking suggests the cooking time. Cooking time may be
adjusted to fit personal preferences and for some meat categories refers to a rare preparation (see
Induction Oven cooking tables for more details).
SETTINGS
1. To modify some display parameters, select “SETTINGS” from the main menu by turning the
“Functions” knob.
2. Confirm by pressing the button : the display shows the parameters that can be modified
(language, acoustic signal volume, display brightness, time of day, energy saving, power, induction
first alert).
3. Select the setting to be changed by turning the “Browse” knob.
4. Press the button to confirm.
5. Follow the instructions on the display to modify the parameter.
6. Press the button ; a message confirming the operation appears on the display.
N.B.: When the oven is switched off, if the ECOMODE (Energy saving) function is selected (ON), the display
switches off after a few seconds, showing the clock. To view information on the display and switch the light
on again, just press any of the buttons or turn one of the knobs. During a cooking function if the ECOMODE
is activated the cavity lamp will be switched off after 1 minute of cooking and reactivated for each user
interaction. If, on the other hand, the function is not selected (OFF), after a few minutes the display is merely
dimmed.
KEY-LOCK
This function can be used to lock the buttons and knobs on the control panel.
To activate it, press the buttons and together for at least 3 seconds. If activated, the functions of the
buttons are locked and the display shows a message and the icon . This function can also be activated
during cooking. To deactivate it, repeat the above procedure. When the key-lock function is activated, the
oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously selected
function will have to be reset.

EN48
DESCRIPTION OF FUNCTIONS TABLE
FUNCTIONS KNOB
OFF To stop cooking and switch off the oven.
INDUCTION
FUNCTIONS See INDUCTION FUNCTIONS.
RECIPES
Selecting 30 different preset recipes (see enclosed recipe-book). The oven
automatically sets the optimum cooking temperature, function and
duration. It is important to follow the instructions given in the recipe-book
regarding preparation, accessories and which level to use.
SETTINGS Setting the display (language, time, brightness, acoustic signal volume,
energy saving).
SPECIALS See SPECIAL FUNCTIONS.
CONVECTION BAKE To cook meat and pies with liquid filling (savoury or sweet) on a single
shelf. Use the 3rd shelf. The oven does not have to be preheated.
FORCED AIR
To cook even different types of food (e.g. fish, vegetables, cakes), requiring
the same cooking temperature, on up to three shelves at the same time.
This function allows cooking without odours being transferred from one
food to another. Use the 3rd level to cook on one shelf only, the 1st and 4th
to cook on two shelves, and the 1st, 3rd and 5th to cook on three shelves.
The oven does not have to be preheated.
GRILL
For grilling steak, kebabs and sausages; vegetables au gratin and toasting
bread. It is advisable to place food on the 4th or 5th level. When grilling
meat, it is advisable to use the drip-tray to collect the cooking juices.
Position it on the 3rd/4th level, adding approx. half a litre of water. The
oven does not have to be preheated. During cooking, the oven door must
remain closed.
TURBO GRILL
For roasting large pieces of meat (legs, roast beef, chickens). Place the food
on the middle levels. It is advisable to use the drip-tray to collect the
cooking juices. Place it on the 1st/2nd level, adding approx. half a litre of
water. The oven does not have to be preheated. During cooking, the oven
door must remain closed. With this function it is also possible to use the
turnspit, if provided.
CONVENTIONAL
To cook any type of dish on a single shelf. Use the 3rd level. To cook pizzas,
savoury pies and sweets with liquid fillings, use the 1st or 2nd level. The
oven does not have to be preheated.
FAST PREHEATING To preheat the oven quickly.
LAMP To switch the oven interior light on/off.

EN49
SPECIAL FUNCTIONS
DEFROST
To speed up defrosting of food. It is advisable to place food on the middle
level. It is advisable to leave food in its packaging to prevent it from
becoming dry on the outside.
KEEP WARM
For keeping just-cooked food (e.g. meat, fried food, flans) hot and crisp. It
is advisable to place food on the middle level. The function will not
activate if the temperature in the oven is above 65°C.
RISING
For optimum rising of sweet or savoury dough. In order to preserve the
quality of proving, the function will not activate if the temperature in the
oven is above 40°C. Place dough on the 2nd level. The oven does not have
to be preheated.
CONVENIENCE
For cooking ready-made foods, kept at room temperature or in
refrigerated counters (biscuits, liquid cake mixtures, muffins, first courses
and bakery products). The function cooks all dishes quickly and gently; it
can also be used to heat already cooked food. Follow the instructions on
the food packaging. The oven does not have to be preheated.
MAXI COOKING
For cooking large pieces of meat (over 2.5 kg). Use the 1st or 2nd level,
depending on the size of the meat. The oven does not have to be
preheated. It is advisable to turn the meat over during cooking, to obtain
even browning on both sides. It is preferable to baste the meat every now
and again so that it does not become too dry.
FROZEN
FOOD
Lasagne
The function automatically selects the ideal cooking temperature and
mode for 5 different categories of ready frozen food. Use the 2nd or 3rd
level. The oven does not have to be preheated.
Pizza
Strudel
French
Fries
Bread
Custom The temperature can be set from 50 to 250°C to cook other types of
products.
SLOW
COOKING
Slow
Cooking
Meat
To gently cook meat (at 90°C) and fish (at 85°C). This function carries out
slow cooking to keep the food more tender and succulent. Thanks to the
low temperature, the food does not brown on the outside and the end
result is similar to steam cooking. For roasts, it is advisable to brown the
meat in the pan first in order to help keep the juices inside. Cooking times
range from 2 hours for fish weighing 300 g to 4-5 hours for a 3 kg fish; for
meat, times range from 4 hours for 1 kg joints to 6-7 hours for 3 kg joints.
For optimum results, do not open the oven door during cooking in order
to avoid heat dispersion; use the temperature probe provided (where
present) or a standard oven thermometer.
Slow
Cooking
Fish
ECO FORCED AIR
For cooking filled roast meats and meat cuts on one level only. This
function uses discontinuous, delicate fan assistance, which prevents
excessive drying of foods. In this ECO function the light is switched off
during cooking and can be temporarily switched on by pressing the
confirmation button. It is advisable to use 3nd level. The oven does not
have to be preheated.

EN50
INDUCTION FUNCTIONS
FOOD
TYPES
Roasted
Meat
Roast beef
4 steps: from 0.6 to 2 kg
The function automatically selects the ideal
cooking temperature and mode for different
weight categories (see oven display). It is
possible to roast any type of meat (e.g. beef,
veal, pork, ribs, lamb, etc.). The function “top
finishing” is optimal to obtain high level of
surface browning.
Roast meat
3 steps: from 1 to 4 kg
fillet / piece
Roasted
poultry
Whole
5 steps: from 0.6 to 3 kg
The function automatically selects the ideal
cooking temperature and mode for different
weight categories (see oven display). It is
possible to roast any type of poultry (e.g.
chicken, turkey, duck etc.). The function “top
finishing” is optimal to obtain high level of
surface browning.
fillet / piece
Fish
Whole
3 steps: from 0.2 to 1 kg
The function automatically selects the ideal
cooking temperature and mode for different
weight categories (see oven display). Is
possible to cook any type of fish (e.g.
swordfish, sea bass, sea bream etc.)
fillet / piece
Vegetables
Roasted Vegetables This function is ideal for cooking different
type of vegetable with the option for roasting
or cooking vegetables filled with other
ingredients such as meat, cheese, béchamel
sauce etc..
Stuffed Vegetables
Cookies/
Muffins
Muffins This function is ideal for cookies or muffins,
from the classic biscuits to small cakes stuffed
with marmalade, chocolate or other
ingredients. Choose the function "Muffins"
when a rising phase is required.
Cookies
Cakes
Sweet Cakes This function is ideal for cooking sweet or
savoury cakes, pies and flans. From the classic
fruit tart to many different types of savoury
flan including Quiche Lorraine.
Savoury Pie/Flan
Pizza
Thin Pizza This function is ideal for cooking all types of
Pizza.
Thick Pizza
Traditional Bread This function is ideal for cooking any type of
taste, shape and flavouring of Pizza
Casserole / Main course
This function is ideal for cooking different
preparations based on pasta, with sauce,
cream, meat, vegetables (e.g. Lasagna).
CUSTOM
Low Power This function is ideal for cooking items that do
not fall into a specific food type category. This
function is divided into three power levels to
allow you to chose between the low, medium
and high combination of the grill and tray. It is
possible to switch between low, medium and
high power levels at any time during cooking.
Medium Power
High Power
REHEATING -
This function is ideal for keeping just-cooked
dishes hot and crisp and allows re-heating of
previously cooked dishes with a gentle
transfer of heat