Bauknecht GKEA 2550 Optima User manual

Bauknecht AG, Industriestrasse 36, 5600 Lenzburg, www.bauknecht.ch
Verkauf Telefon [phone] Fax [phone] [email protected]
Kundendienst Telefon [phone] Fax [phone] [email protected]
Ersatzteile Telefon [phone] Fax [phone] ersatzteilverk[email protected]
Instructions for use
GKEA 2550 Optima

GB
PRODUCT SHEET
1. Compartment for freezing
2. Control unit
3. Area for drawers and pull-out baskets
4. Rating plate (inside
the appliance)
5. Ice packs (inside - if provided)
Note: the design of drawers and accessories may vary, depending on the model.
Controls (depending on model)
ADigital temperature display.
BYellow LED: indicates that the fast freeze
function is in operation.
CRed LED: blinks to indicate that the temperature
in the freezer compartment is too high.
DFreezer on/off button.
EInternal temperature control.
FFast freeze button.
GAcoustic alarm mute button.
H
Switching on
Storage compartment
Area for freezing
1. Plug in the appliance.
Attention
If the digital display shows only
an illuminated dot, press the
freezer on/off button D.
Six horizontal lines appear on the digital
display.
After about 3 seconds, when the appliance is
warm, (internal temperature above 10°C)
only the two lines in the middle remain
illuminated; The acoustic alarm and red LED
Care activated.
2. Press button Gto mute the
acoustic alarm. The acoustic alarm stops while the red LED continues to blink.
3. Wait until the temperature
indicated on the digital display
reaches -12°C.
When the temperature reaches -12°C, the
red LED automatically stops blinking.
4. Place food to be frozen and/or
already frozen food in the
freezer.
“6th Sense”/“Dynamic Intelligence” activation LED
(blue), (if provided).
Indicates that the “6th Sense”/“Dynamic Intelligence”
function is (see paragraph “6th Sense”/“Dynamic
Intelligence” function).
5019 608 01058

D F NL E P GR DK
S N FIN
IGB
PRODUCT SHEET
Freezer compartment temperature adjustment
The appliance is normally factory set for optimum operation at a temperature of -18°C.
To alter the internal temperature between -16°C and -24°C, proceed as follows:
•Press button Eonce to adjust the internal temperature: the digital display shows the temperature previously
set.
•Each time the button is pressed, the temperature setting is changed by 1°C: the value (between -16°C and
-24°C) blinks cyclically on the display.
•Approximately 5 seconds after the button has been pressed for the last time, the set temperature is stored,
the display stops blinking and the current internal temperature is shown on the display.
•
Note:
The digital display shows internal temperature values between +10°C and -24°C.
In the event of a power failure, selected functions remain stored in the memory.
Fast freezing
The fast freeze function switches off automatically when freezing is complete.
Alarm signals
Note:
The temperature alarm may activate if the door is left open for a prolonged period of time or following the
introduction of fresh food in the freezer compartment; this temporary rise in temperature does not affect the
storage of already frozen food in any way.
Defrosting (for No Frost models no operation is required)
This appliance defrosts automatically according to usage and ambient humidity conditions.
Follow the steps detailed in “Switching on the appliance”.
For not No Frost models, follow step 1-6:
Signal Cause Solution
Door open alarm The acoustic alarm is activated The door has been left open
for more than 1 minute Close the door
Temperature alarm The acoustic alarm and red LED C
are activated The internal temperature is above -12°C Press button G; wait for the temperature to fall
below -12°C again
Te m p e r a t u r e s e n s o r
alarm
The acoustic alarm is activated and
the display shows “SF”
Temperature sensor fault Contact After-sales
service
Prolonged power failure
alarm
The acoustic alarm and red LED C
are activated; the display blinks,
indicating the highest temperature
reached following the power failure
Prolonged lack of power
supply, causing the internal
temperature to rise to very
high values at which correct
food storage cannot be
guaranteed
Press button G; the
display now indicates the
current internal
temperture
1. Press the freezer on/off button D. An illuminated dot appears on the digital display.
2. Unplug the appliance or switch off at the main
switch.
3. Fit the drain in place (see figure).
4. Follow the instructions given in the
instructions booklet.
5. Plug in the appliance once again.
6. Press the freezer on/off button D. Follow the steps detailed in “Switching on the
appliance”.
The 6th Sense/“Dynamic Intelligence” function (blue LED) is automatically activated due to door opening and
when small amounts of fresh food are placed in the freezer. The duration of the 6th Sense function varies
depending on the quantity of food loaded in the freezer and ambient temperature. When optimal operating
conditions have been restored the function deactivates automatically and no operation is required.
5019 608 01058
Printed in Italy 03/09

12
INSTRUCTIONS FOR USE
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
HOW TO USE THE FREEZER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
INSTALLATION
ELECTRICAL CONNECTION
40302003GB.fm Page 12 Wednesday, March 8, 2006 3:49 PM

13
BEFORE USING THE APPLIANCE
SAFEGUARDING THE ENVIRONMENT
•Your new appliance is designed exclusively for
domestic use
Forbestuseofyourappliance,carefullyread
the user's handbook which contains a
description of the appliance and advice on
storing and preserving food.
Keep this handbook for future consultation.
1.After unpacking, make sure that the appliance
is undamaged and that the door closes
perfectly tight. Any damage must be reported
toyour dealerwithin 24hours after delivery of
the appliance.
2.Wait at least two hours before switching the
appliance on in order to ensure the refrigerant
circuit is fully efficient.
3.Installation of the appliance and electrical
connections must be carried out by a qualified
electrician, in accordance with the
manufacturer's instructions and local safety
regulations
4.Clean the inside of the appliance before using it.
1.Packing
The packaging material is 100% recyclable and
carries the recycling symbol. Follow local
regulations for scrapping. Keep the packaging
materials (plastic bags, polystyrene parts, etc.)
out of reach of children, as they are potentially
dangerous.
2.Scrapping
The appliance is manufactured using recyclable
material.
This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By making sure this appliance is disposed of
correctly, the user will help prevent potentially
negativeconsequencesforthe environmentand
the health of persons.
The symbol on the appliance, or on the
accompanying documents, indicates that this
applianceshouldnotbetreated asdomesticwaste
butmustbe takento a suitable collection point for
the recycling of electrical and electronic
equipment.
Before scrapping, make the appliance unusable
bycutting off the power cableand removingthe
doors and shelves so that children cannot easily
climb inside the appliance.
Disposalmustbecarriedout inaccordancewith
local environmental regulations for waste
disposal. Deliver the appliance immediately to
an authorized dump; do not leave it unattended
even for a few days, since it is potentially
dangerous for children. For more information
regardingthe treatment,recovery andrecycling
of this appliance, contact your local office, the
domestic waste collection service or the shop
where you purchased the product.
Information:
This appliance does not contain CFCs (the
refrigerant circuit containsR134a) or HFCs (the
refrigerant circuit contains R600a) (see the
rating plate inside the appliance).
Appliances with Isobutane (R600a):
isobutane is a naturally occurring, low
environmental impact gas. Caution is required,
however, because isobutane is flammable.
Therefore, ensure that the pipelines of the
refrigerant circuit do not get damaged.
Declaration of conformity
•This appliance is designed to store food and is
manufactured in conformity with European
Directive 90/128/EEC, 02/72/EEC and
Regulation (EC) No. 1935/2004
•This product has been designed,
manufactured and retailed in compliance
with:
- the safety objectives of the Low Voltage
Directive 73/23/EEC;
- the protection requirements of the “EMC”
Directive 89/336/EEC,
amended by Directive 93/68/EEC.
•The electrical safety of the appliance can only
be guaranteed if the product is connected to
an approved earth connection.
40302003GB.fm Page 13 Wednesday, March 8, 2006 3:49 PM

14
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
•Use the refrigerator compartment only for
the storage of fresh food and the freezer
compartment only for the storage of frozen
food, the freezing of fresh food, and to make
ice cubes.
•During installation, make sure the appliance
does not damage the power cable.
•Do not store glass containers with liquids in
the freezer since they may burst.
•Donoteat icecubesorice lollies immediately
aftertakingthemoutofthefreezersincethey
may cause cold burns.
•Before servicing or cleaning the appliance,
unplug it from the mains or disconnect the
electrical power supply.
•Makesurethattheapplianceisnotnearaheat
source.
•Do not store or use petrol, gas or flammable
liquids in the vicinity of the appliance or other
electrical appliances. The fumes can create a
fire hazard or explosion.
•To ensure adequate ventilation, leave a space
on both sides and above the appliance and
follow the installation instructions.
•Keep the appliance ventilation openings free.
•All appliances equipped with an ice maker or
water dispenser must be connected to a
mains water supply that delivers potable
wateronly (with waterpressure between 1.7
and8.1bar (25and 117PSI)).Ice makersand/
orwaterdispensersnotdirectlyconnectedto
a mains water supply must be filled with
potable water only.
•Installandleveltheapplianceonafloorstrong
enough to take its weight and in an area
suitable for its size and use.
•For the water connection, use the pipe
supplied with the new appliance and do not
use that of the previous appliance.
•The appliance must be handled and installed
by two or more persons.
•Place the appliance in a dry and well-
ventilated place. The appliance is set for
operation at specific ambient temperature
ranges, according to the climatic class
indicatedonthedataplate:Theappliancemay
not work properly if it is left for a long period
at a temperature above or below the
indicated range.
•Becareful not to damagethe floors when you
move the appliance (e.g. parquet flooring).
•Do not use mechanical, electric or chemical
meansotherthanthoserecommendedbythe
Manufacturer to speed up the defrost
process.
•Do not damage the refrigerator's refrigerant
circuit pipes.
•Do not use or place electrical appliances
insidethe compartments ifthey arenotofthe
type expressly authorised by the
Manufacturer.
•This appliance is not designed for use by
young children or the infirm without
supervision.
•Toavoid the riskof children being trapped and
therefore suffocating, do not allow them to
play or hide inside the appliance.
•Power cable modification or replacement
must only be carried out by qualified
personnel.
•Do not use single/multiple adapters or
extension cables.
•It must be possible to disconnect the
appliance from the mains by unplugging it or
by means of a two-pole switchfitted upline of
the socket.
•Ensure that the voltage indicated on the
appliance data plate corresponds to the
domestic supply voltage
•Do not swallow the contents (non-toxic) of
the ice packs (if provided).
•The Manufacturer declines any liability if the
above recommendations and precautions are
not respected.
Climatic class Amb. T. (°C) Amb. T. (°F)
SN From 10 to 32 From 50 to 90
N From 16 to 32 From 61 to 90
ST From 18 to 38 From 64 to 100
T From 18 to 43 From 64 to 110
40302003GB.fm Page 14 Wednesday, March 8, 2006 3:49 PM

15
HOW TO USE THE FREEZER
The freezer can be used for storing already frozen food and
for freezing fresh food.
Switching on the freezer for the first time
•There is no need to set the freezer temperature on the
thermostat because the appliance is already factory set.
•Plug in the appliance.
•Thealarmsignalactivates,indicatingthat thefreezerhasnotyet
reachedasufficiently cold temperatureforstorage offoodstuffs.
•Only place food in the freezer once the alarm signal has
deactivated (for further details, see the enclosed product
sheet).
Temperature Adjustment
For temperature adjustment, see the enclosed product sheet.
Note:
Ambient air temperature, the frequency of door opening and the
position of the appliance can affect the freezer internal
temperature.
Takethesefactorsintoconsideration whensetting thethermostat
knobs.
“6th Sense” function
The 6th Sense function, if present, isautomatically activated inthe
following cases:
Door opening
The function activates when door opening causes the internal
temperature to increase to values that do not ensure safe storage
of food and remains active until optimal storage conditions have
been restored.
Placing fresh food in the freezer
Thefunctionactivates whenfresh food is placed in the freezer and
remains active until optimal freezing conditions are reached so as
to ensure the best freezing quality with the lowest power
consumption.
NOTE: Besides the quantity of food loaded into the freezer,
ambient temperature and the quantity of food already inside the
freezer affect the duration of the 6th Sense function. Therefore
significant duration variations are quite normal.
Freezing
The amount of fresh food (in kg) that can be frozen in 24
hours is indicated on the appliance data plate.
For optimum appliance performance, press the fast freeze button
(until the yellow LED lights up) 24 hours before placing fresh food
in the freezer.
After placing fresh food in the freezer, 24 hours on fast freeze
function is generally sufficient; After 24 hours, deactivate the fast
freeze function
Attention:
In order to save energy, when freezing small amounts of food, the
fast freeze function can be deactivated after a few hours.
If the 6th Sense function is present, appliance operation is
controlledautomatically andnooperationisrequired(seechapter
“6th Sense” function)
40302003GB.fm Page 15 Wednesday, March 8, 2006 3:49 PM

16
Tips for freezing and storing fresh food.
•Before freezing, wrap and seal fresh food in:
aluminium foil, cling film, air and water-tight plastic bags,
polythene containers with lids orfreezer containers suitable for
freezing fresh food.
•Food must be fresh, mature and of prime quality in order to
obtain high quality frozen food.
•Fresh vegetables and fruit should preferably be frozenas soon as
they are picked to maintain the full original nutritional value,
consistency, colour and flavour.
Some meat, especially game, should be hung before it is frozen.
Note:
•Always leave hot food to cool before placing in the freezer.
•Eat fully or partially defrosted foods immediately. Do not
refreeze unless the food is cooked after it has thawed. Once
cooked, the thawed food can be refrozen.
Freezing and storing fresh food
•Place foods to be frozen in the baskets.
•Placethe icepacks (if supplied)above thefood storedin the top
compartment.
•In models with ice packs, in the event of a power failure, place
theicepack/sabovethe foodstoredinthetopcompartment, in
ordertooptimisetherising timeandtherefore maintaincorrect
food preservation.
Important:
The table alongside shows the recommended maximum
storage time for frozen fresh foods.
Declared performance refers to appliance operation
without ice packs, with the exception of the rising time.
Classification of frozen foods
Put the frozen products into the freezer and classify them.
The storage date should be indicated on the packs, to allow use
within expiry dates.
Advice for storing frozen food
When purchasing frozen food products:
•Ensure that the packaging is not damaged (frozen food in
damaged packaging may have deteriorated). If the package is
swollenorhasdamppatches,itmaynothavebeenstoredunder
optimal conditions and defrosting may have already begun.
•When shopping, leave frozen food purchases until last and
transport the products in a thermally insulated cool bag.
•Once at home, place the frozen foods immediately in the
freezer.
•If food has defrosted even partially, do not re-freeze it.
Consume within 24 hours.
•Avoid, or reduce temperature variations to the minimum.
Respect the best-before date on the package.
•Always observe the storage information on the package.
MONTHS FOOD
40302003GB.fm Page 16 Wednesday, March 8, 2006 3:49 PM

17
Removing the baskets
•Pull the baskets out fully, then lift them up slightly in order to
remove.
Drawers(except thebottomdrawer)mayberemovedinorderto
obtain increased storage space (Fig. 1)
Ensure that the load does not exceed the limit (if present)
indicated on the side walls of the appliance.
Please follow the storage times given on the frozen food
packages.
Making ice cubes
•Fill the ice cube tray 2/3 full and place it in the special freezer
compartment.
•Do not use sharp or pointed instruments to detach the tray if it
is stuck to the bottom of the freezer.
•Bend the ice tray slightly to remove the cubes.
Note:
The freezer door will not re-open easily immediately after closing
(except for the models with specific valve).
Wait a few minutes before opening again in order to allow for
compensation of the vacuum created.
Intelligent ice system with feeder
Some models are equipped with an ice system including a feeder,
ice cube trays with removal device and ice bin. Thanks to this
system, it is easy to fill the ice cube trays with water, remove the
ice cubes and store them.
The feeder allows you to easily fill the trays with water without
havingtoremovethemfromthefreezerandwithoutspillingwater
on the kitchen floor.
Filling the trays with water:
•before filling the trays, clean them as described in the cleaning
section.
•To remove the feeder, pull it towards you.
•Fill the feeder with water without resting it on a surface, then
refit it on its support. The water will automatically fill the ice
cube trays.
•Waitforafew hoursfor theiceto beready, thenturnthe knobs
to extract the ice cubes. The ice cubes will fall directly into the
ice bin.
Attention:
•make sure there are no ice cubes in the tray before refitting the
feeder.
•Before refitting the feeder, make sure there is no ice on the
springs; if there is, remove it under running water.
•The removable parts of the ice system may be taken out in
order to obtain increased storage space.
Fig. 1
40302003GB.fm Page 17 Wednesday, March 8, 2006 3:49 PM

18
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
1. The appliance is not working.
•Is there a power failure?
•Is the main power switch on?
•Has the fuse blown?
•Is the thermostat setting correct?
•Was the appliance switched on correctly?
2. Excessive frost build-up.
•Has the defrost water drain been positioned
correctly?
•Is the door shut properly?
3. Theyellow,redand greenLEDsdonot
light up. Perform the checks for point
1, and then:
•Contact After Sales Service.
Notes:
• The front edge of the appliance may be hot.
Thispreventstheformationofcondensation
and is not a defect.
• Gurgling and hissing noises due to
expansion in the refrigerant circuit are
normal.
Before any cleaning or maintenance operation, unplug
the appliance from the mains or disconnect the
electrical power supply.
For electronic models, first press the on/off
button and then unplug the the appliance.
Periodically clean the condenser at the rear of the appliance
with a vacuum cleaner or brush.
Periodically clean the inside of the compartment with a
sponge dampened in warm water and/or neutral detergent.
Rinse and dry with a soft cloth. Do not use abrasive products
Long vacation
•Empty the freezer.
•Disconnect the freezer from the mains power supply.
•Defrost and clean.
Leave the door open to prevent formation of
unpleasant odours and to eliminate any dampness
Note: for electronic models, first insert the power plug
into the mains socket and then press the on/off button
to switch on the appliance.
40302003GB.fm Page 18 Wednesday, March 8, 2006 3:49 PM

19
AFTER SALES SERVICE
Before contacting After Sales Service:
1. See if you can solve the problem yourself with
the help of the Troubleshooting guide.
2. Switch the appliance on again to see if the
problem has been solved. If it has not,
disconnect the appliance from the power
supply and wait for about an hour before
switching on again.
3. If the problem persists after this course of
action, contact After-sales Service.
Specify:
•the nature of the fault,
•the model,
•the Service number (the number after the
word SERVICE on the rating plate on the
inside of the appliance),
•your full address,
•your telephone number and area code.
Note:
The direction of door opening can bechanged.
If this operation is performed by After-sales
Service it is not covered by the warranty.
The door cannot be reversed on models with
front handle.
INSTALLATION
•Installthefreezeraway fromheatsources.Installationinahot
environment, direct exposure to the sun or installation near
heatsources(heaters,radiators,cookers)willincreasepower
consumption and should therefore be avoided.
•If this is not possible, the following minimum distances must
be respected:
•30 cm from coal or paraffin stoves;
•3 cm from electric and/or gas stoves.
•Install the appliance in a dry, well-ventilated place.
•Clean the interior (see “care and maintenance”).
•Fit the accessories supplied (Fig. 1and 2).
Electrical connection
• Electrical connections must be made in accordance
with local regulations.
•Voltage and power consumption are indicated on the rating
plate inside the appliance.
•Regulations require that the appliance is earthed.
The Manufacturer declines all liabilities for injury to
persons or animals or damage to property resulting
from failure to observe these regulations.
•If the plug and socket are not of the same type, have the
socket replaced by a qualified electrician.
•Do not use extension leads or adapters.
Disconnecting the appliance
Electrical disconnection must be possible either by unplugging
theapplianceorbymeansofadouble-poleswitchlocatedupline
from the socket.
Fig. 1
Fig. 2
40302003GB.fm Page 19 Wednesday, March 8, 2006 3:49 PM

20
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS 1362 type and proceedas follows:
1.Remove the fuse cover (A) and fuse (B).
2.Fit replacement 13A fuse into fuse cover.
3.Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the
fuse cover is lost the plug must not be used until a correct
replacement is fitted.
Correct replacement are identified by the colour insert or the
colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please
contact Whirlpool Service for further instruction. Please do not
attempt to change plug yourself. This procedure needs to be
carried out by a qualified Whirlpool technician in compliance
with the manufactures instructions and current standard safety
regulations.
40302003GB.fm Page 20 Wednesday, March 8, 2006 3:49 PM