Baumatic BG60TCBL User manual

1
BG60TCBL/BG60TCSS/BG60TCW 60 cm 4
Burner gas hob with thermocouples
BT62TCSS 60 cm 4 Burner gas hob with
thermocouples
B68TCSS 70 cm 5 Burner gas hob with
thermocou
p
les

User Manual for your Baumatic
BG60TCBL/BG60TCSS/BG60TCW 60 cm 4
Burner gas hob with thermocouples
BT62TCSS 60 cm 4 Burner gas hob with
thermocouples
B68TCSS 70 cm 5 Burner gas hob with
thermocouples
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
DD 05/03/09
2

3
Contents
Environmentalnote 4
Important safety information 5 – 7
Specifications 8 – 12
BG60TCBL/SS/W 8
BT62TCSS 9
B68TCSS 10
Electricaldetails 11
Gasdetails 11
Gashobsurfacelayout 12
Using the gas hob 13 - 15
Beforefirstuse 13
Switchingthehobon 13
Push button ignition with flame failure safety device 13 – 14
(BG60TCBL/SS/W)
Automatic ignition with flame failure safety device 14
(BT62TCSS/B68TCSS)
Energysavingtips 15
Cleaning 16 - 17
Cleaning the hob top 16
Aftereachuse 16
Cleaning the hob burners 16 – 17
Maintaining cast iron pan stands (BT62TCSS/B68TCSS) 17
Installation 17 - 27
Positioning 18
Unpacking the appliance 19
Installing the appliance 19 – 21
Gasconnection 21
Ventilation requirements 22
Gas Safety (Installation and Use) Regulations 23
Gas Adjustment (Conversion to LPG) 24 - 25
Minimum flow adjustment for hob gas taps 25
Gastapmaintenance 26
Electricalconnection 27
Replacing the mains supply cable 27
My appliance isn’t working correctly 28
Contactdetails 29

Environmental note
4
oThe packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
all packaging material with due regard for the
environment.
oPlease discard

5
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If yo
are unsure of any of the information contained in t u his
ooklet, please contact the Baumatic Advice Line.
old use and for
in
ient temperature of the
n at
of this temperature limit, will be the liability of
uarantee. The foregoing does not
f Baumatic Ltd.
ld not use this appliance to store items on or as a work
ept away
service
b
General Information
This appliance is designed for domestic househothe cooking and frying of domestic foodstuffs.
oIMPORTANT: The adjacent furniture and all materials used
the installation must be able to withstand a minimum
temperature of 85°C above the amb
room it is located in, whilst in use.
oCertain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or discolouratio
temperatures below the guidelines given above.
oAny damage caused by the appliance being installed in
contravention
the owner.
oYour new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in Baumatic’s Conditions Of G
affect your statutory rights.
oThe use of this appliance for any other purpose or in any other
environment without the express agreement o
will invalidate any warranty or liability claim.
oYou shou
surface.
oNo modifications to the appliance are permitted by Baumatic Ltd.
oYou should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made
from aluminium, plastic or plastic film should also be k
from the appliance, as they may fuse to the surface.
oRepairs may only be carried out by Baumatic
engineers or their authorised service agent.

6
hild Safety
d
e at any time. During and after use, all
surfaces will be hot.
se ensure that they are kept under close supervision
at all times.
ld only be allowed to utilise the appliance
when supervised.
eneral Safety
e installed and connected by a
CORGI registered installer.
rfaces
ild the appliance into, meet with the relevant
standards.
uring use
ob surface when it
is delivered should be removed before use.
appliance, otherwise
there is a risk of burns being caused.
e
with the hob surface when it is hot or any hot
cookware.
g with fat and oil the appliance should
not be left unattended.
sure that all of the cooking zones are switched off after
use.
leaning
Cleaning of the hob should be carried out on a regular basis.
iance, it
should be disconnected from the mains and cool.
C
oBaumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowe
to touch the applianc
oIf it is necessary for younger family members to be in the
kitchen, plea
oOlder children shou
G
oThe appliance should only b
oCare should be taken to ensure that the units and work su
that you bu
D
oAny film or stickers that are present on the h
oCare should be used when utilising the
oYou should not allow the electrical connection cables to com
into contact
oIf fat and oil overheats, then it can ignite extremely quickly. For
this reason, when cookin
oMake
C
o
oIMPORTANT: Before attempting to clean the appl

oGreat care should be taken whilst using this appliance and when
following the cleaning procedure.
oYou should not use a steam jet or any other high pressure
cleaning equipment to clean the appliance.
Installation
This appliance must be correctly installed by a
CORGI registered installer, strictly in accordance
with the manufacturer’s instructions and the
relevant British Standards. Please see the specific
section of this booklet that refers to installation.
oBaumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a result of improper
use or installation of this appliance.
oIf the appliance is being used in a Leisure Accommodation
Vehicle, the requirements of N 721 MUST be followed.
oBaumatic Ltd. DO NOT recommend that this appliance is
installed on any type of marine vessel.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23/EEC dated 19/02/1973 Low Voltage Directive.
-89/336/EEC dated 03/05/1989 EMC Directive inclusive of
Amending Directive 92/31/EEC.
-93/68/EEC dated 22/07/1993 CE Marking Directive.
-89/109/EEC dated 25/01/1992 Materials that can touch food.
-90/396/EEC Gas Products.
-EN60335-1, EN60335-2, EN301-1 Safety Standards.
The manufacturer declares that the hob is built using certified
materials and requires the appliance to be installed in accordance with
the standards currently in force. This appliance must be used by a
trained person for domestic purposes only.
7

Specifications
BG60TCBL/SS/W
Product dimensions: Aperture dimensions:
Height: 500 mm Height: 480 mm
Width: 585 mm Width: 560 mm
Depth: 35 mm
Product specifications:
o1 x 3.00 kW rapid burner
o2 x 1.75 kW semi-rapid burners
o1 x 1.00 kW auxiliary burner
oSide control operation
oPush button ignition
oEnamelled pan stands
oFlame failure safety device on each burner
Standard accessories:
oLPG conversion jets
8

BT62TCSS
Product dimensions: Aperture dimensions:
Height: 500 mm Height: 480 mm
Width: 585 mm Width: 560 mm
Depth: 35 mm
Product specifications:
o1 x 3.30 kW wok burner
o2 x 1.75 kW semi-rapid burners
o1 x 1.00 kW auxiliary burner
oFront control operation
oAutomatic ignition
oHeavy duty cast iron pan stands
oFlame failure safety device on each burner
Standard accessories:
oLPG conversion jets
oWok stand
9

B68TCSS
Product dimensions: Aperture dimensions:
Height: 510 mm Height: 480 mm
Width: 685 mm Width: 560 mm
Depth: 35 mm
Product specifications:
o1 x 3.30 kW wok burner
o1 x 3.00 kW rapid burner
o2 x 1.75 kW semi-rapid burners
o1 x 1.00 kW auxiliary burner
oFront control operation
oAutomatic ignition
oHeavy duty cast iron pan stands
oFlame failure safety device on each burner
oFits into a standard 60 cm cut-out
Standard accessories:
oLPG conversion jets
oWok stand
10

11
Electrical details
Rated Voltage: 230 Vac 50 Hz
Supply Connection: 3 A (double pole switched fused outlet with
3mm contact gap)
Max Rated Inputs: 0.008 to 0.02 kW (depending on model)
Mains Supply Lead: 3 core x 0.75mm²
Gas details
Connection: Rp ½ (ISO R7)
Type: Natural Gas (20.9 mbar),
Alternative LPG G30 (28-30 mbar),
Town gas G110 – 120 (8 mbar) to order.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your hob is located on
the underneath of the appliance. Therefore it is a good idea to record
this information before you install your appliance.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….

Gas hob surface layout
BG60TCBL/SS/W
BT62TCSS
B68TCSS
12

Using the gas hob
Before first use
IMPORTANT: You should clean the hob surface (see
“Cleaning and maintenance” section).
Switching the hob on
The following symbols will appear on the control panel, next to each
control knob:
0 = gas off
Large flame: maximum setting
Small flame: minimum setting
oThe minimum setting is at the end of the anti-clockwise rotation
of the control knob.
oAll operation positions must be selected between the maximum
and minimum position.
oNever select a knob position between the maximum and off
position.
oThe symbol on the control panel, next to the control knob will
indicate which gas burner it operates.
Push button ignition with flame failure safety device
(BG60TCBL/SS/W)
The appliance is fitted with a flame failure safety device on each
burner, which is designed to stop the flow of gas to the burner head in
the event of the flame going out.
oPress in and turn the appropriate control knob anti-clockwise to
the large flame symbol.
oWhilst pressing in the control knob, press and hold down the
ignition button, which is located on the control panel.
oYou should hold down the ignition button for 20 seconds after
the flame on the burner has lit.
13

14
oAfter this 20 second interval, turn the control knob to your
required setting between the maximum and minimum setting
symbols.
oTo turn the burner off, turn the control knob fully clockwise to
the gas off position.
oIn case of power failure, the burners can be lit by carefully using
a match.
Automatic ignition with flame failure safety device
(BT62TCSS/B68TCSS)
The appliance is fitted with a flame failure safety device on each
burner, which is designed to stop the flow of gas to the burner head in
the event of the flame going out.
To ignite a burner:
oPress in the control knob of the burner that you wish to light and
turn it anti-clockwise to the maximum position.
oIf you keep the control knob depressed, the automatic ignition
for the burner will operate.
oYou should hold down the control knob for 20 seconds after the
flame on the burner has lit.
oAfter this 20 second interval, turn the control knob to your
required setting between the maximum and minimum setting
symbols.
oTo turn the burner off, turn the control knob fully clockwise to
the gas off position.
oIn case of power failure, the burners can be lit by carefully using
a match.

Energy saving tips
PANSBURNERS
Minimum
diametre
Maximum
diametre
Wok 220 mm 260 mm
Rapid 180 mm 220 mm
Semi-rapid 120 mm 200 mm
Auxiliary 80 mm 160 mm
oThe diametre of the bottom of the pan should correspond to that
of the burner.
oThe burner flame must never extend beyond the diametre of the
pan.
oUse flat bottomed pans only
oWhen possible, keep a lid on the pan whilst cooking.
oCook vegetables with as little water as possible, to reduce
cooking times.
IMPORTANT: Always place pans centrally over the hob burners and
position them so that the handles cannot get accidentally caught or
knocked off. You should also make sure that the handle is not over one
of the other hob burner flames.
15

Cleaning
Cleaning operations must only be carried out when
the hob is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
Cleaning the hob top
Any residues that are left on the hob top surface from cleaning
agents will damage it. You should remove any residues with
warm soapy water.
Abrasive cleaners or sharp objects will damage the hob surface;
you should clean it using warm soapy water.
Although it is easier to clean some deposits whilst the
hob surface is still warm. Make sure that the hob surface,
pan supports and hob burners have all cooled sufficiently
before you attempt to touch them.
After each use
oRemove the pan stands and wipe the appliance over with a soft,
damp cloth that has been put into warm soapy water. The cloth
should be wrung out after being taken out of the soapy water.
oDry the appliance by rubbing the surface with a soft, clean cloth.
oWe would recommend that an appropriate stainless steel cleaner
and polish is regularly used on the stainless steel surfaces of this
appliance.
Cleaning the hob burners
The hob burners should be cleaned once a week or more frequently if
they get soiled.
oIMPORTANT: Make sure that the hob surface, pan stands and
hob burners have cooled before you attempt to touch them.
oRemove the hob burners by pulling them upwards and away
from the hob top.
oSoak them for about ten minutes in hot water and a little
detergent.
16

oAfter cleaning and washing them, wipe and dry them carefully.
oBefore placing the burners back on the hob top, make sure that
the gas jet is not blocked.
oIMPORTANT: Make sure that you reassemble the burners in the
original way.
Maintaining cast iron pan stands (BT62TCSS/B68TCSS)
oIMPORTANT: Make sure that the hob surface and pan stands
have cooled before you attempt to touch them.
oWipe the pan stands over with a soft, damp cloth that has been
put into warm soapy water. The cloth should be wrung out after
being taken out of the soapy water.
oUsing a paper towel, thoroughly dry the pan stands.
oTo maintain the appearance of the cast iron pan stands, we
would recommend that you rub a small amount of olive oil into
the pan stands. After you have finished cleaning them.
Installation
The installation must be carried out by a CORGI
registered installer, in accordance with the current
version of the following.
oGas safety Regulations (Installation & Use)
oBuilding Regulations (issued by the Department of Environment)
oBuilding Standards (Issued by the Scottish Development
Department)
oIEE Wiring Regulations
oElectricity at Work Regulations BS 6172
oInstallation of Domestic Gas Cooking Appliances (if necessary,
BS 5482 Installation of Domestic LPG Appliances)
oBS 5440 Installation of Flues and Ventilation for Gas Appliances
oBaumatic Ltd Installation Instructions
17

Positioning
The adjacent furniture must be able to withstand a
minimum temperature rise of 85°C above the ambient
temperature of the room it is located in, during
periods of use.
oThis appliance can be located in a kitchen, a kitchen diner or a
bed sitting room. IMPORTANT: The appliance must not be
installed in a bathroom or shower room.
This appliance is classified as Class 3 and therefore is to be built into a
kitchen unit (depending on size) or 600mm worktop, providing the
following minimum distances are allowed:
oThe edges of the hob must be a minimum distance of 55 mm
from a side or rear wall.
o700 mm between the highest point of the hob surface (including
the burners) and the underside of any horizontal surface directly
above it.
o400 mm between the hob surface, providing that the underside
of the horizontal surface is in line with the outer edge of the hob.
If the underside of the horizontal surface is lower than 400 mm,
then it must be at least 50 mm away from the outer edges of
the hob.
o50 mm clearance around the appliance and between the hob
surface and any combustible materials.
18

Unpacking the appliance
When unpacking the appliance please check that the following items
are contained within the packaging:
1 x Baumatic hob 1 x Baumatic guarantee card
2 x Pan stands 4 x Fixing screws
3 x Pan stands (B68TCSS) 4 x Clamps
4 x Burner assemblies 1 x Sealing strip
5 x Burner assemblies
(B68TCSS) 4 x LPG jets 5 x LPG jets (B68TCSS)
1 x Installation and instruction
manual
1 x Self-adhesive label for amending the Gas Category on the
appliance’s rating plate (required if the LPG conversion kit is used).
Installing the appliance
BG60TCBL/SS/W & BT62CSS
B68TCSS
19

oCut a hole in the worktop that corresponds with the drawings
shown on page 19.
oIMPORTANT: You must have a gap of at least 25 mm between
the underneath of the appliance and any surface that is below it.
oCarefully turn the hob upside down and place it on a cushioned
mat.
oApply the sealing strip (A) provided around the edge of the
appliance.
oThe protective covering must be removed from both sides.
oDo not leave a gap in the sealing agent or overlap the thickness.
oIMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it difficult to remove the hob
from the aperture in future, particularly if it needs to be
serviced.
(A) Sealing strip
(B) Clamp
(C) Screw
20