Baxi Fires Division 339 User manual

600B687/11
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Model339
HeartbeatOxysafe2
LIVE FUEL EFFECT GAS FIRE
(GC No. 32-032-29)
INSTALLER: Please leave this guide with the
owner
We trust that this guide gives
sufficient details to enable this
appliance to be operated and
maintained satisfactorily. However, if
further information is required, our
Baxi Fires Division Technical
Helpline will be pleased to help.
Telephone [phone] (National
call rates apply in the United
Kingdom).
In the Republic of Ireland
Telephone [phone].
This guide is intended to help you care
for your Baxi Fires Division gas fire.
Please read thoroughly before using
and keep for future reference.

© Baxi Heating U.K. Limited 2007.
All rights reserved. No part of this publication may be reproduced in any material form
(including photocopying), stored in any medium by electronic means (including in any
retrieval system or database) or transmitted, in any form or by any means, whether
electronic, mechanical, recording or otherwise, without the prior written permission of
the copyright owner.
Applications for the copyright owner's permission to reproduce any part of this
publication should be made, giving details of the proposed use, to the following address:
The Company Secretary, Baxi Heating UK Limited, Pentagon House, Sir Frank Whittle
Road, Derby, DE21 4XA.
Warning: Any person who does any unauthorised act in relation to a copyright work may
be liable to criminal prosecution and civil claims for damages.
Baxi Fires Division, Erdington, Birmingham B24 9QP
www.firesandstoves.co.uk
Because our policy is one of constant development and improvement, details may vary slightly from those
given in this publication
Page 2
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).
THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED
KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Safety First.
Baxi Fires Division fires are CE Approved and designed to meet the appropriate British
Standards and Safety Marks.
Quality and Excellence.
All Baxi Fires Division fires are manufactured to the highest standards of quality and
excellence and are manufactured under a BS EN ISO 9001 quality system accepted by
the British Standards Institute.
The Highest Standards
Baxi Fires Division is a member of the Society of British Gas Industries which works to
ensure high standards of safety, quality and performance.
Careful Installation
Baxi Fires Division is a CORGI registered company. All our gas fires must be
installed by a competent CORGI Registered Installer in accordance
with our Installer Guide and should not be fitted directly on to a
carpet or floor of combustible material.
Page 3
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.

LIST OF CONTENTS
Section
Page
SAFETY 4
APPLIANCE DIMENSIONS 6
GAS CONSUMPTION 6
OPERATING YOUR FIRE 7
CLEANING YOUR FIRE 9
MAINTENANCE 10
USEFUL TELEPHONE NUMBERS 11
This gas fire is designed to meet the most stringent quality, performance and safety
requirements to provide you with many years’ trouble-free service.
This guide aims to improve your understanding and appreciation of your gas fire by
providing simple and informative instructions to ensure that you benefit from the
excellent performance and features it has to offer.
SAFETY
Do have the fire installed by a competent person. In the United Kingdom, installation
must be in accordance with the latest edition of the Gas Safety (installation & use)
Regulations. In the Republic of Ireland, installation must be in accordance with all
national and local regulations in force.
Do
have the chimney swept prior to installation if it was previously used for solid fuel.
Do have the fire installed in accordance with the installer guide.
Do provide a suitable guard that complies with BS 8423 for the protection of young
children, the elderly and the infirm. Such a guard is also recommended for the protectio
n
of pet animals. (
Although this fire conforms to all the applicable standards, it is a heating
appliance and certain parts of its surface will become hot).
Note: The glass panel supplied with the fire acts as a fireguard conforming to
BS1945:1971
and satisfies the Heating Appliance (Fireguard) (Safety) Regulations1991.
Page 4
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
IF YOU SMELL GAS
! DON’T SMOKE.
! EXTINGUISH ALL NAKED FLAMES.
! DON’T TURN ELECTRICAL SWITCHES ON OR OFF.
! TURN OFF THE GAS SUPPLY AT THE METER.
! OPEN DOORS AND WINDOWS TO GET RID OF THE GAS.
! IMMEDIATELY CALL THE GAS EMERGENCY SERVICE FROM A
NEIGHBOURS PHONE - SEE YOUR LOCAL TELEPHONE DIRECTORY.

Do wait three minutes before attempting to relight if the fire is switched off or the
flames are extinguished for any reason. (Your fire is fitted with a safety device that will
automatically shut off the gas supply to the fire if, for any reason, the flames go out).
Do get advice about the suitability of any wall covering near your fire. Soft wall
coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by
heat. They may, therefore, scorch or become discoloured when close to a heating
appliance. Please bear this in mind whenever you are considering redecorating.
Do allow a minimum clearance of 150mm from the top of the appliance fascia to the
underside of any shelf made from non-combustible materials. This clearance is
necessary to allow the fascia to be lifted off for servicing. For a shelf made from wood
or other combustible materials the minimum clearance from the top of the appliance
fascia to the underside of the shelf is 150mm, for combustible shelves deeper than
150mm add 12.5mm to the clearance for every 25mm of additional shelf depth (See
graph 1). Please bear this in mind if ever you add a shelf.
Do provide a minimum clearance of 100mm between the fascia sides and any corner
wall having combustible material or other combustible surface which projects beyond
the front of the fire (See figure 1). Please bear this in mind if ever you are considering
altering the room.
Don’t hang clothing, towels or any other fabrics over the fire.
Don’t fill in the space behind the fascia.
Don’t use the fire with a damaged ceramic fuel effect or with the ceramic fuel effect
incorrectly positioned.
Don’t use the fire if the glass window is damaged.
Page 5
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Graph 1. Combustible shelf clearances

Don’t
attempt to clean or service the fire until it has been switched off and allowed to
cool completely.
Don’t
allow any combustible material (e.g. Wallpaper, plastic tiling, wood panelling etc)
on the surface wall below below the shelf.
APPLIANCE DIMENSIONS
GAS CONSUMPTION
Has a maximum natural gas input of 5.1kW (Gross)
Has a maximum natural gas output of 3.6kW
Has a minimum natural gas input of 1.5kW (Gross)
Has a minimum natural gas output of 0.8kW
Page 6
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 1 Dimensions and clearances
See graph 1

OPERATING YOUR FIRE
The Oxysafe flame sensing and flue blockage safety system.
For your safety, this appliance is fitted with a flue blockage safety device that will shut
down the appliance in the event of abnormal flue conditions. This device is NOT a
substitute for an independently mounted Carbon Monoxide detector.
The device will also automatically shut off the gas supply to the fire if the pilot flame
goes out due to lack of oxygen or for any other reason.
If this device starts to repeatedly shut off the gas, get expert advice.
This device incorporates a probe that senses that the heat from the pilot flame is correct.
If this probe is cool, the device will prevent any gas flow unless the control knob is held
down at the ignition position.
If, for any reason, the flames go out when the fire is hot or if the fire is turned off when
hot, always wait at least three minutes before attempting to relight.
To light the fire.
The control is shown in Figure 2.
·Depress the control knob and turn partially to the
1/IGN position until you feel some resistance.
·Keep the knob depressed at this position for a few
seconds to allow gas to flow to the burner.
·While keeping the knob depressed, turn to the
1/IGN position. While turning, a spark should light
the pilot.
·Keep the knob depressed at the 1/IGN position for a
further 10 seconds then release it. The centre section
of the ceramic fuel effect will be alight at this
position.
·Depress the control knob slightly and turn it to your desired burner setting.
·The control knob should be depressed slightly before turning whenever you are
Page 7
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
PLEASE NOTE
When operating your fire for the first time, some vapours may be given off which may
cause a slight odour and could possibly set off any smoke alarms in the immediate
vicinity. These vapours are quite normal with new appliances. They are totally harmless
and will disappear after a few hours use.
Figure 2.

Page 8
changing the burner setting.
·The burner settings are;
·
We recommend that the fire is set at position 4 for the first 10 minutes after lighting
to warm up the chimney and so obtain full efficiency quickly.
·
If operating the appliance for long periods it is beneficial occasionally to change the
settings. This will also help to remove any carbon deposits that may form during
operation.
Note: If the fire goes out while setting the control, repeat the full lighting procedure. If
the fire repeatedly goes out, have the fire serviced.
To turn the fire off.
·Partially depress the control knob and turn clockwise to OFF. Release the knob.
·Wait at least 3 minutes after turning the fire off before relighting.
Lighting with a taper.
In the unlikely event of failure of the ignition spark, the pilot can be lit with a taper or
long spill after the window surround has been
removed. Removal of the surround is described in
the "Window Glass" chapter on the next page.
Light the pilot by inserting the taper or spill below
the centre of the window while the control is kept
depressed at the 1/IGN position (See figure 3).
When the pilot has lit follow the rest of the
instructions in the section headed "To light the
fire". Always replace the window unit after
lighting.
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Control Knob
Position Burner appearance
1 / IGN Centre section on low. Outer sections off.
2Centre section fully on. Outer sections off.
3Centre section fully on. Outer sections on low.
4 All sections fully on.
Figure 3.

CLEANING YOUR FIRE
To maintain the high performance and quality
finish of your Baxi Fires Division fire, please
follow these guidelines:
·Before attempting to clean the fire, please
remember to turn off the fire and wait for the
appliance to cool. The fire will retain heat for
some time before cleaning can begin.
·If any pieces of debris are found in the fire
box, have the chimney inspected before
further use.
Metal parts.
·Clean the metal parts with a slightly damp
cloth and then dry.
·Do not use abrasive cleaners as these will
scratch the fire surface.
Window glass.
·Remove any stains on the window with a
non-abrasive cleaner such as a ceramic hob
cleaner. Do not use abrasive cleaners.
·The fire has been designed to so that you
can remove the window without having to call
in a service engineer. This allows you to clean the inside of the window.
To remove the window:
1.
Unscrew and remove the two knurled screws which are under the fascia canopy (See
figure 4).
2. Pull the top of the window surround forward (See figure 4).
3.
Lift the window surround up to clear the slots in the fascia apron (See figure 4). Put
the surround in a safe place.
4.
Remove the window unit by removing the screws each side of the window frame and
lift the window unit clear.
5. After cleaning, replace and secure the window unit using the two screws removed
previously. Replace the surround. Make sure that the outside edges of the window
surround sides are inside the fascia.
Page 9
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 4.

Ceramic fuel effect.
·
This product uses a ceramic fuel effect containing Refractory Ceramic Fibres (RCF),
which are man-made vitreous silicate fibres. Excessive exposure to this material may
cause temporary irritation to eyes, skin and respiratory tract. Consequently, it makes
sense to take care when handling this article to ensure that the release of dust is kept to a
minimum.
·
Although light coatings of soot are usually burnt off during normal use, the ceramic
fuel effect may benefit from occasional cleaning.
·Should any soot accumulation become excessive, the
fuel effect piece should be removed from the fire for
cleaning. Cleaning should be carried out in a well
ventilated area or in the open air by gently brushing
with the pieces held away from your face so that you
avoid inhaling the dust. We do not recommend the use
of a normal domestic vacuum cleaner which may blow
dust back into the air.
·The ceramic fuel effect can be lifted out of the fire
box when the window surround and glass have been
removed as described on page 9.
·When replacing the ceramic fuel effect, make sure
that it rests on the ledges at the sides of the firebox and
that its back face is touching the horizontal rib at the
back of the firebox (See figure 5).
·Replace the window and surround after cleaning.
MAINTENANCE
Regular maintenance.
In order to achieve and maintain high levels of personal safety and performance
efficiency, it is essential that the opening at the back of the fire and the flue are kept
clear of any form of obstruction. It is possible that deposits of mortar or soot could fall
and accumulate causing the flue to be blocked or restricted and so preventing proper
clearance of dangerous exhaust fumes.
In the United Kingdom it is the law that a landlord must have any gas appliance, flue
and pipework which is situated in a tenant’s premises checked for safety at least every
twelve months by a competent person (In the U.K., a CORGI registered installer).
We recommend that all gas appliances and their flues, wherever situated, are checked
annually.
Page 10
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 5. Ceramic fuel
effect location

Servicing.
!
In the United Kingdom servicing can be carried out either by a Baxi Fires Division
service engineer or a CORGI registered installer.
! If you require your fire to be serviced, please contact
Baxi Fires Division Service
on 08706 090 081 and quote the following details;
Model name and number.
Appliance serial number (To be found on a label near the bottom left side of the
fascia).
! If you wish to replace the ceramic fuel effect,
spare parts are available nationwide
via the ‘interpart stockist network
’. For your local stockist consult Yellow pages
under Central Heating.
!
When fitting replacement parts, follow the instructions contained in this guide. It
is important that only Baxi Fires Division approved parts are used for maximum
safety.
USEFUL TELEPHONE NUMBERS
General advice about gas and your gas fire:
BAXI FIRES DIVISION TECHNICAL HELPLINE 08706 061 065.
To report faults or arrange for your fire to be serviced:
BAXI FIRES DIVISION SERVICE 08706 090 081.
For sales or product information:
BAXI FIRES DIVISION SALES 08706 061 067.
For spares inquiries:
Spare parts are available nationwide via the ‘interpart stockist network’. For your
local stockist consult Yellow pages under ‘Central Heating’.
CALLERS IN THE REPUBLIC OF IRELAND
Call 0044 8706 061 065
Page 11
OWNER GUIDE
© Baxi Heating U.K. Limited 2007.