Baxton Studio ABBIE DAYBED-F/T User manual

NO PART LIST QTY
BACK REST 1PC
SIDE PANEL
(L)
FRONT
SIDE RAIL
LEG
ITEM HARDWARE QTY
JCBB SCREW
M8 x 20MM
L - KEY
M5 x 65MM
1PC
1PC
4PCS
20PCS
STEP 1
STEP 3
1
2
3
4
5
ABBIE DAYBED-F/T
ABBIE DAYBED-Q/T
6
SIDE PANEL
(R)
Please do not tighten the hardware until the entire assembly is completed.
7
1PC
8
SLAT 2 SET
SPRING WASHER
FLAT WASHER
(BIG)
FLAT WASHER
(SMALL)
L - KEY
M4 x 100MM
SCREW
M4 x 32MM
SCREW
M4 x 16MM
4PCS
12PCS
24PCS
16PCS
22PCS
1PC
1PC
A
B20PCS
JCBC SCREW
M6 x 50MM
C
D
E
F
G
H
I
J
9
7pcs
2PCS
2PCS
BACK
SIDE RAIL
1PC
1PC
SLAT
SUPPORT
SUPPORT
LEG
STOPPER
Begin assembly by attaching each Leg (6) to the bottom of the
Side Panel (2) & (3) securing with 2 Allen Bolt (B) per panel using
L-key (H).
STEP 2
Attach the Front Rail (4) and Back Rail (5) to the Side Panel (2) & (3)
aligning holes and securing with 2 Allen Bolts (A) per each end using
L-key (I). (DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
Attach the Back Rest (1) to the back of each Side Panel (2) & (3) by
aligning the hole and securing with 2 Allen Bolts (B), 2 Spring Washer
(C), 2 Flat Washer (D) from the back side per each end using L-key (H).
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
STEP 4
Secure 2 Support Leg (9) to the Slat Support (8) as shown on step 4.1.
Insert the pre-set metal on Slat Support (8) to the metal bracket on each
side of Side Panel (2) & (3). Then securing the metal bracket as shown
in step 4.3 with 1 Screw (G) each side using Phillips Head Screwdriver
(NOT INCLUDED)
10
11
12
13
14
15
1PC
1PC
TRUNDLE
FRONT RAIL
TRUNDLE
BACK RAIL
TRUNDLE
SIDE RAIL 2PCS
SLAT
5pcs
2 SET
SLAT
SUPPORT 3PCS
6PCS
CASTOR
AI
6BH
HB
D
C
1
STEP 4.2
STEP 4.3
8
G
STEP 4.1 8
9
2
43
8
1
2
4
3
1
4
2
5
3
23

STEP 5 STEP 6
STEP 7
Please do not tighten the hardware until the entire assembly is completed.
Tighten All Bolts from step 1 to step 4 by using L-key (I) & (J) that has been provided.
Attached Slat (7) to Front Side Rail (4) & Back Side Rail (5) by unrolling and securing
with 6 Screw (G), per set using Phillips Head Screwdriver. Securing Slat (7) to Back Side
Rail (5) with 2 Screw (G) per each side as step 5.1. Following by step 5.2, using 1 Screw
(G) to secure Slat (7) to Front Side Rail (4).
Repeat the same step to attach another set of Slat (7).
Attach the Stopper (J) to the front side of Side Panel (2) & (3) each side by
securing with 2 Allen Bolt (A) using L-key (I) to avoid trundle pull out.
4
JA
I
STEP 5.2
G
7
STEP 5.1
G
7
4
7
5
2
3

Please do not tighten the hardware until the entire assembly is completed.
J
1
3
3
2
5
6
3
4
4
TRUNDLE
FULL SET ASSEMBLY
COMPLETE
Assembly by tracing around the Castors (15)
onto the Slats Support (14). Secure Castors (15)
to Slats Support (14) using 4 Screws (F)
per castor.
Tighten screws with Phillips screwdriver
(NOT INCLUDED)
Begin with attaching Trundle Side Rail (12) to Front Rail (10)
& Back Rail (11) using 2 Bolts (A) per corner.
Tighten bolts with Allen Key (I) provided.
Attach Slat Support (14) to Front Rail (10)
& Back Rail (11) using 2 Bolts (B),
2 Spring Washers (C) and 2 Flat
Washer (E) on each end of each
Slat Support (14). Tighten bolts with
Allen Key (H).
Attach Slat (13) to Front Rail (10) & Back
Rail (11) using 4 Screws (G) per set.
Tighten screws with Phillips screwdriver
(NOY INCLUDED)
STEP 8
STEP 10
STEP 9
STEP 11
12
10
11
12
A
I12
10
14
12
11
15
14
F
12
10
12
14
H
B
C
E
10 13
13
G