Bazooka MC-HD-AK2 User manual

Harley Davidson Installation Manuel
Preparation
This sheet must be read completely to:
1. Provide assistance/clarification to the installer.
2. Avoid causing injury to installer, customer,
end user, or others.
3. Prevent damage to motorcycle and/or
accessory.
4. Prevent death to customer or other vehicle
operators.
Installer: Please forward this sheet to the
customer after reviewing it.
It is virtually impossible for us to be able to
address every possible situation an installer or
user will encounter. This requires both to
exercise due diligence and to apply some level of
common sense. If you have any question or
problem during the installation, please contact us
as necessary. Read the instructions completely
prior to installation. 90% of questions we receive
could be answered simply by reading the
instructions in their entirety. Phone support will
always provide the quickest response.
Important Information in our instructions will be
provided in the following manner:
SHOPTIP: this is information we have gathered
from hands-on installs or customer feedback.
NOTE: important information regarding the
installation.
CAUTION: failure to follow instructions could
result in damage to motorcycle and/or accessory.
WARNING: failure to follow instructions could
result in injury or death of operator and/or
passenger or others.
NOTE:
1. "Left", "Right", "Front" and "Rear" are
described from the seated position of the bike.
2. Use of owners manual or service manual is
recommended for installation.
3. If so equipped, place the motorcycle on its
center stand on solid, level ground.
CAUTION:
1. Never route wires or install components that
interfere with the operation of the forks,
handlebars, brake/clutch levers or any other
operational function of the motorcycle.
2. When adding electrical accessories, always
disconnect the battery and properly fuse new
electronics.
WARNING:
1. Allow the motorcycle to cool prior to
installation.
2. When operating engine, allow adequate
ventilation.
3. Never route wires or install components that
interfere with the operation of the forks,
handlebars, brake/clutch levers or any other
operational function of the motorcycle.
4. Never allow your accessories to cause
distractions to remove your focus off the bikes
operation. Never forget that this is a high-risk
sport - don't make it a higher risk when you don't
have to.
5. Never allow your accessories to cause
distractions to others on the road.

Harley Davidson Installation Manuel
Preparation
Disassembly of Motorcycle:
1. With motorcycle on its center stand and on solid level
ground, switch off ignition switch and remove seat.
2. Before doing any electrical work to your motorcycle.
It is good practice to disconnect the negative
battery
terminal, then the positive terminal. Disconnecting
the terminals in this order will minimize the chance
of sparks and voltage spikes. When reconnecting
do
the reverse connect positive then negative
terminals.
1. Remove bolts at the bottom of the fairing inside of
theforks.(2 bolts) ( Fig. 1-1 )
2. Remove bolts under handgrips on outer fairing.
(2 bolts) ( Fig. 1-2 )
3. Remove bolts in front of firing. Remove outlet bolts.
Leaving center bolt to hold fairing. Remove center
bolt and unplug headlight. (3 bolts) ( Fig. 1-3 )
Fig 1-1
Fig 1-2
Fig 1-3

Harley Davidson Installation Manuel
Preparation
Installation of Harness
1. Unplug factory radio harness.
2. Plug in Bazooka fast harness into radio and plug
factory harness into Bazooka fast harness.
( Fig. 2-1 )
3. Run red power wire to battery leaving fuse block
with the factory fuses. Make sure fuse is removed
during installAttach ground wire to triple tree
ground terminal. Left side cover. ( Fig. 2-1)
4. Replace factory speakers. All speakers are shipped
with grills and in some cases rubber magnet
covers.
These are for shipping protection only. If rubber
magnet covers are on the speakers, they MUST be
removed prior to installation. Discard the grills and
use the OEM grills to complete the installation.
5. The front and rear speakers are clearly marked and
must be used as such .The front speakers must be
slid
into the speakers mounts with the crossover
network
placed toward the outside of the fairing and the
speaker terminals to the inside for ease of
installation. The rear speakers should be mounted
with the crossover network toward the rear of the
bike.
Tech Tip:
Fig. 2-2 is an example of where the crossover on the
speaker should be located.
Fig. 2-3 is an example of where the crossover on the
speaker should NOT be located.
Tech Tip:
Make sure the speaker connectors on the wire harness
are securely attached to the terminals of the Bazooka
speakers. You may need to take a pair of needle nose
pliers and crimp the female connector on the harness
onto the speaker spade to insure you have a good
connection that will not loosen up over time. You can
also use finger nail polish or blue lock tight to further
secure this connection.
Fig. 2-1
Fig. 2-2
Fig. 2-3

Harley Davidson Installation Manuel
Preparation
6. Make sure fast harness is tie wrapped out of the way
prior to replacing fairing check to make sure you
have proper clearance DO NOT!!!! Force fairing
back into place. Always check your HD Manuel for
proper torque settings.
7. If you have a CB on your Harley Davidson you’ll
need
to relocate it under the radio using 3M
double-sided
tape provided in kit looking at the back of the radio
it fits best on the right side under the radio this
frees
up the top for mounting the Bazooka amp.
( Fig. 3-1 )
7. Always make sure the power wire or ground wire
DO NOT interfere with the turning of the front end.
8. Prior to reassembly. Plug in fuse. Power up the radio
and set the gain located in the center of the amp on
the power and ground side. (Most applications need
only to be set just passed half way)
9. Reassemble and enjoy your Bazooka sound system
and visit us at www.bazooka.com and tell us about
your new system.
MC-HD-AK2/MC-HD-AK4 Speaker Specs.
WOOFER:
Size 5.25 Midrange
Impedance 4 ohm
Power Handling 120 watts
Sensitivity 88db @ 1w @ 1 meter
Frequency Response 60-20 kHz +/- 3db
Mounting Depth 2 "
Features:
Solid aluminum cone with a rubber surround
TWEETER:
Size .75
Features:
Spun aluminum dome with a neodymium magnet and
adjustable swivel. Crossover 12 db per octave, two
stage crossover, bi-ampable
Fig. 3-1