Bazooka MT6100BTA User manual

//
//
1.
2.
4.
3.
MT6100BTA
MT6100BTAL
1. Active BT tubbie stand
2. Passive BT tubbie stand with 6 ft. cable
3. Passive BT tubbie
4. Amplified BT tubbie
5. 6 ft. power extention cable
Unlatch nut (7) and clamp (8)
locking tabs.Then unscrew
wingnut (9).
Line amplified tubbie (4) up
with the PCB mount on the top
of the tubbie stand (1).Then push
down firmly until clamp snaps in place.
Clamp locking tab (8) *MUST*
be latched before tightening
wingnut (9)
Tighten clamp wingnut (9).
Then close nut locking tab (7).
Then repeat steps to mount
passive tubbie (3) to passive
stand (2)
8.
7.
9.
8.
7.
9.
5.
Installation Instructions
Optional power adapter
for 110v AC to 12v DC
*Not Included*

MT6100BTA
MT6100BTAL
Installation Instructions
MT6100BTA & MT6100BTAL can be mounted to the
Power Rail PR3256 & PR3256K. Use the same mounting
procdure as mounting them to the tubbie stands.
(see page 1)
CAUTION:The Power Rail master power switch should
always be in the OFF position before adding
or exchanging accessories.
MT6100BTA & MT6100BTAL can be mounted to the
marine tubbie quick disconnect clamps MT-CL2-B,
MT-CL2-SS, and MT-CL3-SS. Use the same mounting
procdure as mounting them to the tubbie stands.
(see page 1)
Red +12v DC
Black -12v DC
Step 1. Decide which clamp is going to the used for the
amplified tubbie clamp and which will be the passive
tubbie clamp.
Step 2. Follow the clamp mounting directions that where
provided with the clamps.
Step 3. Run a positive 12v DC wire to the red wire and a neg-
ative 12v DC wire to the black wire on the amplifed
tubbie and passive tubbie mounting clamp PCB
pigtails.
Step 4. Run a jumper wire between the 2 white wires on the
amplifed tubbie and passive tubbie mounting clamp
PCB pigtails.
Step 5. Run a jumper wire between the 2 grey wires on the
amplifed tubbie and passive tubbie mounting clamp
PCB pigtails.
Step 6. Use the same mounting procdure as mounting tubbies
to the tubbie stands. (see page 1)
Amplified tubbie
mount
Passive tubbie
mount
To be able to use the MT6100BTA & MT6100BTAL with
the bar mount clamps you will have to wire clamps in
this configuration.
Power Rail Mount
(Not Included)
Roll Bar / Wake Tower Mount
(Not Included)

Installation Instructions
Button 1 Press to go back one track, Press and hold to decrease volume.
Button 2 Press to play/pause, Press to answer/hang up phone, Double
press for last number radial or open Siri on Iphone, Press and
hold to unpair bluetooth device.
Button 3 Press to go forward one track, Press and hold to increase volume.
Button 4 Press to power on, press while power is on to switch input between
aux. and bluetooth inputs, Press and hold to power off.
Button 5 Floodlight on/off switch only operable on the MT6100BTAL.
MT6100BTA
MT6100BTAL
5
12345
LED Light
Input
Microphone
Aux input jack on amplified tubbie
LED light status indicator:
LED Light Description
Blinking: Bluetooth module is pairing
Solid blue: Bluetooth module is paired
Blue/Red: Bluetooth module is in AUX input mode
Bluetooth module audio indicators:
Audio Response Description
Power on: Module is turned on
Power off: Module is turned off
Beep: After LED light stops blinking means module is paired
Beep: When play/pause button is pressed and held means
module is unpaired from Bluetooth device.
Double Beep: When forward button is pressed and held means
module has reached maximum volume.

LIMITED WARRANTY
®
Southern Audio Services, Inc.., warrants all products to be free from defects in material and workmanship for a period of one (1) year from
the date of purchase. In the event the product is not as warranted, SAS’s sole obligation shall be to repair or replace the defective product at
SAS’s option: SAS limits its obligation under any implied warranties under state laws to a period not to exceed the limited warranty period.
SAS and its authorized dealers specically disclaim liability for any incidental or consequential damages. Some states do not allow limita
tions on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusions may not apply to you. This warranty gives you specic legal rights, and you mayhave
otherrights,which vary from stateto state.
What is covered: This warranty covers all defects in materials or workmanship (partsandlabor)intheproduct.
Whatisnotcovered:Thiswarrantydoesnotcoverthefollowing:
1. DamagesoccurringduringshipmentoftheproducttoSASforrepair(Claimsmustbepresentedtothecarrier).
2. Damagescausedbyaccident,abuse,negligence,misuseorimproper Operationorinstallation.
3. DamagescausedbyanactofGod,includingwithoutlimitation,re,ood Stormorotheractsofnature.
4. Anyproduct,whichhasaserialnumber,defaced,altered,modied,or removed.
5. AnyproductthathasbeenalteredormodiedwithoutSAS’sconsent.
How to obtain warranty services:
1. You are responsible for delivery of the product to SAS or contact SAS at 1-800-THE TUBE for a Return Authorization number. The Return
Authorization number must be clearlywritten on the outside of the box. Freight must be prepaid to SAS. Warranty replacement parts will be
returned freight prepaid. The entire product may be returned for warranty service, but return will be freight collect.
2. You must provide proof of the date of purchase of the product. If proof of purchase is not provided, original date of manufacture
will be used to determine warrantyperiod.
3. Youmustpackagetheproductsecurelytoavoiddamageduringshipment.
4. After acquiring a Return Authorization number, ship to the address below. Please completethis sectionand retainfor your records.
FCC Compliance Statement
This device complies with Part 15 of the FCC rules. Operation of the device is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operations.
Changes or modications not expressly approved by the party responsible for compliance could void the users authority
to operate this device
Southern Audio Services
14763 Florida Blvd.
Baton Rouge La. 70819
Model(s) purchased_______________________________________________________________________________
Serial number(s)__________________________________________________________________________________
Date Purchased___________________________________________________________________________________
Place of Purchase__________________________________________________________________________________
Contact: www.bazooka.com www.atvpowerrail.com [email protected] 1-800-843-8823 or 225-272-7135