BCP SKY1643 User manual

SKY1643
Ver. 2
INSTRUCTION
MANUAL
Curved Electric Fireplace

Pg. 2
Pg. 2
Thank you for choosing us! Since 2002, Best
Choice Products has been bringing customers
high-quality products at the absolute lowest
price. With everything ranging from instruments
and toys to furniture and outdoor, we’ve got
your everyday living essentials covered. We’re
centered around a customer-first philosophy –
with free shipping, exceptional customer
service, and a catalog sourced with you in mind.

Pg. 3
Please retain these instructions for future reference.
NOTICE
The following safety hazards may result in serious injury or death:
• Please read through all instructions before mounting and using this fireplace.
• This fireplace is not intended for commercial use.
• This product should be wall-mounted at least 2 ft. above the ground.
• There should be at least 3.5 ft. clearance between this product and the ceiling.
• The wall bracket on this product should only be fit per manual instructions.
• Do not install this unit onto a carpeted surface or onto any surface that could disrupt airflow to and
from vents.
• Only use this heater with an AC power supply with the correct voltage.
• Cord should only be routed to the bottom right of the fireplace.
• Unplug fireplace when not in use. Turn o fireplace before unplugging unit.
• Do not plug in other devices into the same circuit.
• Do not turn the appliance on until it is properly installed.
• Do not leave appliance unattended during use or when plugged in.
• Do not let children operate or go near this appliance.
• Do not let children or small pets near during mounting and installation.
• Do not operate this product if the cord or any parts of this appliance are damaged. Do not attempt
to modify the cord.
• Periodically check the cord and appliance for damage.
• Do not run cord under rugs, furniture, etc.
• Do not allow cord to hang over sharp edges or place near hot surfaces.
• Do not cover or obstruct the heater in any way.
• Do not store flammable liquids near this heater.
• Do not touch this heater when it is in use.
• Never immerse this appliance or cord in water or any other liquids.
• Do not expose this heater to water or humidity.
• Repairs to this appliance should only be performed by a licensed and qualified electrician.
• Disconnect and discontinue use of this appliance if any water damage occurs, or if the unit becomes
hot to the touch, broken, or smokes/smells like smoke.
• Do not dispose of this appliance as unsorted waste. Use special collection facilities for electrical
appliances.
NOTE: When the heat function is turned on for the first time, a slight odor may be present. This is
normal and should not occur again.
SPECIFICATIONS
Power Supply
Rated Power
110-120 V
1500 W
Lighting (3) 40W G9 Bulbs

Pg. 4
APPROXIMATELY
45 MIN.
45LY
1 PERSON
ASSEMBLY APPROXIMATELY
45 MIN.
ASSEMBLY
2 PERSON
ASSEMBLY
PHILLIPS
SCREWDRIVER
ELECTRIC
DRILL
TOOLS REQUIRED
PARTS
HARDWARE
1
6 PCS
2
2 PCS
3
6 PCS
4
6 PCS
A
D
BC
1 PC
1 BAG
1 PC 1 PC
FIREPLACE/HEATER
4X40MM
SCREWS
TOP
BRACKET
BOTTOM
BRACKET
4X8MM
SCREWS
BEVELED
SCREWS
WALL
ANCHORS
REMOTE CONTROL STAND
PEBBLES
5
1 PC
6
1 PC

Pg. 5
• Position the part 5 top bracket on the wall and mark where the four screw holes will be. Make sure that
the bracket is level.
• Use an electric drill to drill the screw holes.
Screw four part 4 wall anchors into holes,
then attach the part 5 top bracket to the
wall with four part 1 screws.
Attach the part 6 bottom bracket to
the bottom of the part A fireplace with
two part 2 screws.
WALL
TOOLS REQUIREDMOUNTING TO THE WALL
1
2
5
4
1
A
2
6

Pg. 6
Lift the fireplace and carefully lower it onto
the top bracket, ensuring that the bracket and
fireplace are firmly engaged.
Mark the position on the wall of the two screw
holes required for the part 5 bottom bracket.
Carefully remove the fireplace from wall.
3
TOOLS REQUIREDMOUNTING TO THE WALL
WALL

Pg. 7
• Use an electric drill to drill the screw holes for the bottom bracket.
• Screw two part 4 wall anchors into holes.
4
WALL
4
Lift the fireplace onto the top bracket. Attach
the fireplace to the wall with two part 1 screws
on the bottom bracket.
TOOLS REQUIREDMOUNTING TO THE WALL
1

Pg. 8
2
MOUNTING TO A STAND
PLACING THE PEBBLES
2
1
Attach the part C stand to the part A fireplace
with six part 3 beveled screws.
Carefully lift the glass o the front of the part A
fireplace. Arrange the part D pebbles according
to your preference. Replace the glass.
A
AD
33
C

Pg. 9
HEATER/FIREPLACE OPERATION
CONTROL PANEL
• This appliance has a safety-cut o that will engage if the fireplace overheats. The fireplace
will NOT automatically reset for safety reasons. To reset the appliance, unplug the unit for
15 minutes and then plug it back in.
• This appliance can be controlled by the panel on the unit or the remote.
• Do not press the buttons more than once in two seconds; it takes some time for the
fireplace to respond.
ON/OFF: Turn the heating/display eect on and o.
DIMMER: Controls the brightness levels. Press to cycle through dimness levels and the OFF setting.
HEAT 1/HEAT 2: Controls the heating level. Press to cycle through the low setting (750W), high setting
(1500W), and the OFF setting.
STANDBY SWITCH: Press to toggle standby on/o. This must be switched on to use the heater/fireplace.
It is located on the right side of the fireplace.
ON/OFF DIMMER HEAT 1
HEAT 2
• Turn unit o and unplug before any maintenance. Wait at least 15 minutes after
unplugging before cleaning or maintenance.
• Use a vacuum/duster to keep vent area and heater clear of debris and dust.
• Fireplace exterior should be cleaned with a damp cloth or duster.
• Do not use abrasive cleaners or liquids.
CARING FOR YOUR HEATER

RELEASE
ON/OFF
DIMMER HEAT
Pg. 10
REPLACING BATTERIES
The remote has a 3V CR2025 lithium cell battery included. Remove the slip between the
battery and contacts before operating the remote.
DIMMER: Adjust dimmer settings
HEAT: Adjust heat settings
REMOTE CONTROL OPERATION
• Press the release and slide open the back panel of the remote.
• Remove the battery.
• Insert a brand new CR2025 battery, ensuring the “+” and “-“ signs are in the correct order.
• Replace back panel.

• Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Do not put batteries next to or in a heat source (fire, electronic heating device, etc.).
• Do not hit batteries against hard objects.
• Do not submerge batteries in water.
• Batteries should be inserted with the correct polarity.
WARNINGS REGARDING BATTERIES
Pg. 11

All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the
item is returned in its original product packaging and all accessories from its original shipment are included. All
returned items will receive a full refund back to the original payment method. All returned items will not be charged
a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best Choice
Products Customer Service Representative when the return request is submitted. Items received without an RA
may not be accepted or may increase your return processing time. Once an item has been received by Best Choice
Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer’s expense. If the
reason for return is a result of an error by Best Choice Products then Best Choice Products will provide a pre-paid
shipping label via email. Boxes for return shipping will not be provided by Best Choice Products, and is the
customer’s responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are
not considered undamaged until they are received by Best Choice Products and verified as such. All damages to
items are the customer’s responsibility until the item has been received by and acknowledge by Best Choice
Products as undamaged.
CONTACT US; WE’RE HERE 7 DAYS A WEEK TO HELP YOU!
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or
loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
PRODUCT WARRANTY INFORMATION
bestchoiceproducts.com customerservice@
bestchoiceproducts.com 844.948.8400 LEARN MORE!
ASSEMBLY IS COMPLETE!