BCP SKY2950 User manual

SKY2950
Ver. 2
INSTRUCTION
MANUAL
38"Vertical Electric Fireplace

Pg. 2
Pg. 2
Thank you for choosing us! Since 2002, Best
Choice Products has been bringing customers
high-quality products at the absolute lowest
price. With everything ranging from instruments
and toys to furniture and outdoor, we’ve got
your everyday living essentials covered. We’re
centered around a customer-first philosophy –
with free shipping, exceptional customer
service, and a catalog sourced with you in mind.

• Please read through all instructions before mounting and using this fireplace.
• Do not use the fireplace insert with any other mantel than the one provided by the manufacturer.
• Do not use this heater if it is not installed properly in the mantel.
• Firmly secure all screws and knobs before use.
• Reconfirm that all screws and knobs are secure every 90 days.
• Only use this heater with an AC power supply with the correct voltage. (~110-120).
• Do not plug in other devices into the same circuit.
• Do not turn the appliance on until it is properly installed.
• Do not leave appliance unattended during use or when plugged in.
• Do not let children operate or go near this appliance.
• Do not let children or small pets near during mounting and installation.
• Fireplace contains a front panel made of glass. Be careful and exercise caution when handling glass.
• Do not operate this product if the cord or any parts of this appliance are damaged. Do not attempt to
modify the cord.
• Periodically check the cord and appliance for damage.
• Ensure plug fits securely in grounded outlet. If a grounding adaptor is needed to plug in this product,
ensure adaptor is screwed on tight.
• Do not run cord under rugs, furniture, etc.
• Do not allow cord to hang over sharp edges or place near hot surfaces.
• Do not cover or obstruct the heater in any way.
• Never immerse this appliance or cord in water or any other liquids.
• Do not attempt to replace the bulbs. Only a licensed and qualified electrician should do so.
• Repairs to this appliance should only be performed by a licensed and qualified electrician.
• Disconnect and discontinue use of this appliance if any water damage occurs, or if the unit becomes hot
to the touch, broken, or smokes/smells like smoke.
• Do not store flammable liquids or any other materials anywhere near this appliance.
• Do not attempt to modify this product. Modifying this product may result in injury or damage and voids
any and all warranties.
• Do not dispose of this appliance as unsorted waste. Use special collection facilities for electrical appliances.
NOTE: When the heat function is turned on for the first time, a slight odor may be present. This is normal
and should not occur again.
NOTICE Please retain these instructions for future reference.
SPECIFICATIONS
Power Supply
Rated Power
120 V/60 Hz
750 W/1500 W
Pg. 3

HARDWARE
APPROXIMATELY
30 MINUTE
ASSEMBLY
2 PERSON
ASSEMBLY
TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
PARTS
1
4 PCS
2
4 PCS
3
1 PC
6x25 mm WALL ANCHOR TOP BRACKET
1 PC
FIREPLACE/HEATER
1 PC
REMOTE CONTROL
1 PC
CRYSTAL STONES
AB C
NO. 6
DRILL BIT
ELECTRIC
DRILL
Pg. 4

1
• Position the part 3 top bracket on the wall and mark where the four screw holes will be. Make sure that
the bracket is level.
• Use an electric drill and size 6 drill bit to drill four screw holes.
NOTE: It is recommended to use a level to ensure holes are drilled at an even height.
Screw four part 2 wall anchors into holes,
then attach the part 3 top bracket to the
wall with four part 1 screws.
Lift the part A fireplace and carefully
lower it onto the top bracket, ensuring
that the bracket and fireplace are
firmly engaged.
WALL
TOOLS REQUIREDWALL MOUNT ASSEMBLY
1
2
32
1
WALL
A
Pg. 5

Remove the two screws on the sides of the part A fireplace
that secure the glass.
Carefully lift the glass o the fireplace.
Arrange the part C crystal stones
according to your preference.
TOOLS REQUIREDPLACING THE CRYSTALS
1
3
2
Replace the glass and
secure it with screws.
C
Pg. 6

Pg. 7
HEATER/FIREPLACE OPERATION
• This appliance has a safety-cut o that will engage if the fireplace overheats. The fireplace will NOT
automatically reset for safety reasons. To reset the appliance, unplug the unit for 15 minutes and then
plug it back in.
• This appliance can be controlled by the panel on the unit or the remote.
• Do not press the buttons more than once in two seconds; it takes some time for the fireplace to respond.
1234
1. ON/OFF: Turn the heating/display eect on and o.
2. DIMMER: Controls the brightness levels. Press to cycle through five brightness levels and the OFF
setting. Press and hold for three seconds to switch between three flame colors – orange, blue, and
red.
3. HEAT 1/ HEAT 2: Controls the heating level. Press to cycle through the low setting (750W), high
setting (1500W), and the OFF setting.
4. STANDBY SWITCH: Press to toggle standby on/o. This must be switched on to use the
heater/fireplace. It is located on the right side of the fireplace.
REMOTE CONTROL OPERATION
The remote has a 3V CR2025 lithium cell battery included. Remove the slip between the battery and
contacts before operating the remote.
ON/OFF
COLOR – Change flame color
DIMMER – Adjust dimmer settings
HEAT – Adjust heat settings
REPLACING BATTERIES
• Press the release and slide open the back panel of the remote.
• Remove the battery.
• Insert a brand new CR2025 battery, ensuring the “+” and “-“ signs are in the correct order.
•Replace back panel.
ON/OFF DIMMER HEAT1/
HEAT2

All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the
item is returned in its original product packaging and all accessories from its original shipment are included. All
returned items will receive a full refund back to the original payment method. All returned items will not be charged
a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best Choice
Products Customer Service Representative when the return request is submitted. Items received without an RA
may not be accepted or may increase your return processing time. Once an item has been received by Best Choice
Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer’s expense. If the
reason for return is a result of an error by Best Choice Products then Best Choice Products will provide a pre-paid
shipping label via email. Boxes for return shipping will not be provided by Best Choice Products, and is the
customer’s responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are
not considered undamaged until they are received by Best Choice Products and verified as such. All damages to
items are the customer’s responsibility until the item has been received by and acknowledge by Best Choice
Products as undamaged.
CONTACT US; WE’RE HERE 7 DAYS A WEEK TO HELP YOU!
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or
loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
PRODUCT WARRANTY INFORMATION
bestchoiceproducts.com customerservice@
bestchoiceproducts.com 844.948.8400 LEARN MORE!
CARING FOR YOUR HEATER
• Turn unit o and unplug before any maintenance. Wait at least 15 minutes after unplugging before
cleaning or maintenance.
• Use a vacuum/duster to keep vent area and heater clear of debris and dust.
• Fireplace exterior should be cleaned with a damp cloth or duster.
• Do not use abrasive cleaners or liquids.
WARNINGS REGARDING BATTERIES
• Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Do not put batteries next to or in a heat source (fire, electronic heating device, etc.).
• Do not hit batteries against hard objects.
• Do not submerge batteries in water.
• Batteries should be inserted with the correct polarity.