Caesar Fireplace CHFP-102A User manual

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ETL
CHFP-102A
ELECTRIC FIREPLACE
INSTALLATION AND
OPERATING INSTRUCTIONS
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
SAFETY INFORMATION
!WARNING
Phone [phone] Fax [phone] www.caesarfireplace.com [email protected]· · ·
If the information in these instructions
are not followed exactly, a fire may
result, causing property damage,
personal injury or loss of life.
19295 E. Walnut Dr N, City of Industry, CA 91748
C US

2
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 PACKING LIST
2.0
3.0 INTRODUCTION
3.1 DIMENSIONS
3.2 LISTING APPROVALS
3.3 GENERAL INSTRUCTIONS
4.0 PLACING APPLIANCE
4.1 UNPACKING AND TESTING APPLIANCE
4.2 GROUNDING APPLIANCE
5.0 INSTALLATION
5.1 WALL-MOUNT INSTALLATION
5.2 RECESSED INSTALLATION
5.3 FREE STANDING INSTALLATION (OPTION)
6.0 FINISHING
6.1 GLASS DOOR REMOVAL
6.2 MEDIA BED KITS INSTALLATION
6.2.1 6 INTERCHANGEABLE MEDIA BED KITS OPTIONS
6.3 GLASS DOOR INSTALLATION
7.0 OPERATING INSTRUCTIONS
7.1 MAIN POWER BUTTON
7.2 REMOTE CONTROL
7.2.1 BATTERY INSTALLATION
7.2.2 REMOTE OPERATION
7.3 PANEL CONTROL
8.0
8.1 PARTIALLY REFLECTIVE GLASS CLEANING
8.2 GLASS DOOR CLEANING
8.3 SERVICING
9.0 REPLACEMENT PARTS
10.0 WARRANTY
WELCOME & CONGRATULATIONS
MAINTENANCE
3
4
4
5
5
6
7
7
7
8
9
10
10
11
11
12
12
13
13
13
14
14
14
15
16
16
16
16
17
18

1.0 PACKING LIST
No
Description
Quantity
1
Electric fireplace
1 pc
2
Installation and operating instructions
1 pc
3
Remote control (battery included)
1 pc
4
Media bed kits (falling stars )
4 boxes
5
Wall mount bracket
1 pc
6
Wall anchors
13 sets
12
5
3
3
6
4

3.0 INTRODUCTION
2.0 WELCOME & CONGRATULATIONS
Thank you and congratulations for choosing to purchase an electric fireplace from Caesar Fireplace,
the world leader in electric fireplaces. To view the full line of Caesar Fireplace products, please visit
www.caesarfireplace.com.
4
!
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF TOUCHED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug
Do not install damaged incomplete or substitute components.
Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers young children and others may be susceptible to accidental contact burns.
Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
It is imperative that the control compartments, circulating blower and its passageway in the appliance
and are kept clean. The appliance should be inspected before use and at least annually by a qualifed
service person.
Under no circumstances should this appliance be modified.
Do not use this appliance if any part has been in contact with water. Immediately call a qualified service
technician
to inspect the appliance and to replace any part of the control system which has been in contact
with water.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualifed service person.
Do not strike or slam shut the appliance glass door.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
w ith all plastic bags, these are not toys and should be kept away from children and infants.
Servicing should be done only while the appliance is disconnected from the power supply circuit.
Always unplug appliance when not in use.
Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
Do not use appliance outdoors.
Never place appliance where it may fall into a bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, etc. Arrange cord away
from cluttered area and where it will not be tripped over.
Connect to properly grounded outlets only.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the appliance.
To prevent a possible f i r e , do not block air intakes or exhaust in any manner. Do not use on soft surfaces,
like a carpet, where openings may become blocked.
Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or r elocatable
power tap outlet/power strip)(.
To prevent accidental swallowing, media bed kits should be kept away from children and infants.
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
from outlet.
Remote control contains small batteries. Keep away from children. If swallowed, seek medical attention
immediately.
Do not install battery backwards, charge, put in fire or mix with used or other battery types-may explode
or leak causing injury.
·
·
,
,

3.1 DIMENSIONS
3.2 LISTING APPROVALS
This appliance has been tested in accordance with the ETL Standards for fixed and location-dedicated electric
room appliances in the United States and Canada. If you need assistance during installation, please contact
your local dealer.
NOTE: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest edition
in the United States or the Canadian Electric Code, ETL in
Canada.
5
FRONT VIEW
TOP VIEW
SIDE VIEW
22-3/4 (578mm)"
6-3/4 (171mm)"
102 (2590mm)"
24 (610mm)"
96-1/2 (2451mm)"
Heat Vents
（Do not cover）
Model Number CHFP-102A
Description
Voltage 110V AC
Watts Max 1500W
Amps 13 AMP
Appliance Width 102" mm)(2590
Appliance Height 24" 610mm( )
Appliance Depth 6-3/4" 171mm( )
Net Weight 152lbs (69kgs)
Gross Weight 161lbs (73kgs)
Btus 5100 BTU
Power Line
Wall-mount,
recessed,
or free standing
Appliance
6-1/2 (161mm)"

6
3.3 GENERAL INSTRUCTIONS
This electric appliance meets the construction and safety standards of H U D for application in manufactured . . .
.
homes
when installed according to these instructions
!
WARNING
READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION FAILURE TO .
FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE.
DO NOT OPEN RISK OF ELECTRIC SHOCK NO USER-SERVICEABLE PARTS INSIDE. . .
DO NOT USE DAMAGED ELECTRICAL CORDS.
SERVICING SHOULD BE DONE ONLY WHEN THE APPLIANCE IS DISCONNECTED FROM THE
POWER SUPPLY CIRCUIT.
TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF
RECEPTACLE AND FULLY INSERT.
APrior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the outlet are on
B The appliance may emit a slight, harmless odor when first used. This odor is normal and it is caused by the
initial heating of internal appliance elements and will not occur again.
C If your appliance does not emit heat, consult the operation section of this manual for further information.
D Use with and ETL or UL certified surge protector.
.
.
.
.
.

!
WARNING
4.0 PLACING APPLIANCE
4.2 GROUNDING APPLIANCE
NEVER PLACE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER
WATER CONTAINER.
WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND
MAINTENANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION THE ELECTRIC APPLIANCE ,
MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION LOCALIZED .
OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.
DO NOT EXPOSE THE ELECTRIC APPLIANCE TO ELEMENTS, SUCH AS RAIN ETC, .
GROUNDING METHODS
METAL SCREW
(A)
NOT ALLOWED IN CANADA
GROUNDING
MEANS
ADAPTER
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX
(C)
(B)
This appliance is for use on 110 Volts. The cord has a plug
as shown in A An adapter as shown in is available ( ). (C)
for connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as
a properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove
plug from outlet.
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance
operates properly by plugging the power supply cord into a conveniently located 110 Volt grounded outlet.
4.1 UNPACKING AND TESTING APPLIANCE
7

5.0 INSTALLATION
!
WARNING
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE SECURE CORD TO AVOID .
TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN ,
CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS RUNNERS, ETC ARRANGE CORD , .
AWAY FROM CLUTTERED AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.
RISK OF FIRE TO PREVENT A POSSIBLE FIRE DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER DO NOT . , .
USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE. .
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES .
USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE
WARRANTY AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY A FIRE MAY RESULT ,
CAUSING PROPERTY DAMAGE PERSONAL INJURY OR DEATH DO NOT STORE OR USE GASOLINE OR OTHER , .
FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE..
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE , .
NOTE: Follow all National and local electrical codes.
8
.

5.1 INSTALLING THE APPLIANCE
9
SIDE VIEW
22-3/4 (578mm)"
6-3/4 (171mm)"
Hooks Wall Mount
Bracket
SLOTS
REAR VIEW
Power Line
AHave two people hold the appliance against the wall to determine the final
location
B. Mark out location, then mount the bracket onto the wall using the nine
supplied screws.This bracket MUST have the hooks facing upward and be leveled.
NOTE: It is strongly recomme n d e d t h a t t h e m o u n t i n g bracke t be
screwed into the wall studs where possible. If the wall studs cannot be
used, ensure that the supplied plastic anchors are used to affix the
bracket to the wall and the bracket is adequately secured.
C. With the wall mounting bracket installed, have two people lift the appliance
up and insert the three hooks on the bracket into the three slots on the back
of the appliance.
D. Check the appliance for stability, ensuring that the bracket will not break free
from the wall.
.
.
the
D ue to the many different materials used on different walls, it is highly recommended that you
consult your local builder before you install this appliance on the wall.
Screw×9
Wall anchor×9

5.3 FREE STANDING INSTALLATION (OPTION)
A Fix the pillar and plate with 4 screws, as shown in the figure (A).
B Upend the box, then fix it and base with 4 screws at the bottom of the box, as shown in the figure (B).
C. Fix another two plates and base with 4 screws. Base installation is finished, as shown in the figure (C).
D. Put the hooks on the both sides of glass door into the holes in the box. Then push down the glass door to its place.
.
.
FRONT VIEW
102 (2590mm)"
25-1/2 (648mm)"
A
C
B
A
C
B
10
5.2 RECESSED INSTALLATION
FRONT VIEW
96-1/2 (2451mm)"
Screw×4
Wall anchor×4
SIDE VIEW
SIDE VIEW
22-3/4 (578mm)"
Power Line
4 (102mm)"
22-3/4 (578mm)"
A Leave a frame in the wall, the size is W96-1/2"×H22-3/4"×D4".
B. Have two people put the box into the wall, and fix the box to the wall with self-tapping screws.
C. Put the hooks on the both sides of glass door into the holes in the box. Then push down the glass door to its place.
D. Check the appliance for stability, ensuring that the appliance will not break free from the wall.
.
Screw×16
Screw×8

Data LinePower Line
6 1 GLASS DOOR REMOVAL.
6.0 FINISHING
11
OPENINGS, OPERATION OF DOORS OR ACCESS FOR SERVICE. OBSERVE
A.
B. To d
Plastic Connector Plastic Connector
C. Remove the glass door from appliance.
Two people to hold the glass door and lift the door until it’s out of the holes.
isconnect the data line and power line, press the plastic connector, then pull them out.

12
6 2 MEDIA BED KITS INSTALLATION .
NOTE: Glass front must be removed and the appliance must be finished in its final location before the media
bed kits are installed. Media bed kits may have sharp edges, wear safety glasses and gloves when handling.
Carefully place media bed kits into the bottom tray on the front of the appliance
as illustrated. Apply an even layer from side to side.
Model
CHFP-102A
Media
bed kits
Morocco
Dream
Winter
Flakes
Thahiti Getaway
Falling
Stars
Glamour
Night
Treasure
Hunt
Quantity
3 boxes
4 boxes
2 boxes (2 bags of soft
sand included)
4 boxes
3 boxes
3 boxes
6 2.1 6 INTERCHANGEABLE MEDIA BED KITS OPTIONS.
Morocco Dream Winter Flakes Thahiti Getaway
Falling Stars Glamour Night Treasure Hunt

FRONT VIEW
POWER BUTTON
6.3 GLASS DOOR INSTALLATION
A. To connect power line, align the plastic connector and red dot, then connect data line.
B. Two people to hold the glass door and put the hooks into the holes.
C. Check the glass door for stability, ensuring the hooks will not break free from the holes.
7.1 MAIN POWER BUTTON
Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.
The Main Power Button is located on the right of the control panel as illustrated.
Press this button to turn on the appliance. Press again and the button will bounce back. The appliance is turned off.
7.0 OPERATING INSTRUCTIONS
13

14
7.2.2 REMOTE OPERATION
Make certain that new batteries are installed correctly and the appliance turned on!
The remote control will NOT work if the Main Power Switch is NOT pressed down. When
operating the remote control, it must be directed towards the right of the appliance.
NOTE:
A. Plug in your electric appliance.
B. Press POWER button, the appliance is on standby mode. " "
C. The ON/OFF" button can be used to power up or down the appliance. Pressing
this button activates the power to the appliance. Long-press this button for 6 seconds,
then after a beep, heating function will be locked,
Also long-press for 6 seconds again to unlock heating function.
,
"
the backlight of this button will be
off. Under the locked
mode "HEAT" button is not available.
EN
D. To change flame color, press the "COLOR A button.
from, red, yellow, blue, and multicolor.
,
,
" There are 4 colors to choose
The indicator will show digital "1" to "4" when
changing colors. When you press the button for 3 seconds until you hear a beep the indicator
will show digital "0" the flame color and brightness will be changed automatically.
E. To change flame bed color, press the "COLOR B button.
blue, cyan, purple, and white.
, ,
" There are 7 colors to choose from, red, green, yellow,
The indicator will show digital "1" to "7" when changing colors. When you press the
button for 3 seconds until you hear a beep the indicator will show digital "0" the flame bed color and brightness
will be changed automatically.
F. To change brightness, press the DIMMER button. 5 adjustments to choose from.
" " There are The indicator
will show "L1" to "L5" when pressing this button.
7.2 REMOTE CONTROL
7.2.1 BATTERY INSTALLATION
A. Pulling the battery holder out of the slot remote.
B. Install the battery. It uses CR 2032 battery.
C. Reinstall the battery holder into the remote by sliding it into position, as shown.
Remote
(REAR VIEW)
Battery must be recycled or disposed of
properly. Check with your Local Authority or
Retailer for recycling advice in your area.
Battery (CR 2032)
Battery Holder

15
7.3 PANEL CONTROL
Panel control is the same as remote control.
G. To change flame speed, press the SPEED button. There are 5 speeds to choose from.
" " The
show "V1" to "V5" when pressing this button.
indicator will
J. turn on the appliance, all the backlight will be lighted up. Do not press any button for 20 seconds, all
the backlight will be off.
When you
K. Press the "ON/OFF" buttom to turn off the appliance.
I. Press "TIMER" button, this sets the timing for switching the fireplace off automatically. The timer
ranges from 1 to 8 hours, which will be shown on the indicator from "1H" to "8H". Timer is turned off when the
indicator shows "0H". If the appliance is restarted, timer also needs to be reset again.
NOTE: This remote control must remain within 8 meters or 26 feet of the appliance to be effective and this
range may be reduced as the battery power is depleted.
H. to activate the heater press the HEAT button. The initial set-up heat level will be
set for low heat 750W , "-". To adjust the heat level press again for high heat (1500W ,
"--". Press it for the third time, then the mechanism will stop function. After 10 seconds,
" ".
Under the unlock mode
the indicator will show
indicator will show the
indicator will show 0F
, , " "
( ) ) the

16
8.0 MAINTENANCE
!
WARNING
DISCONNECT POWER AND ALLOW HEATER TO COOL BEFORE ATTEMPTING ANY MAINTENANCE OR CLEANING TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR DAMAGE TO PERSON.
THE FIREPLACE SHOULD NOT BE OPERATED WITH AN ACCUMULATION OF DUST OR DIRT ON OR IN THE UNIT, AS
THIS CAN CAUSE A BUILD UP OF HEAT AND SUBSEQUENT EVENTUAL DAMAGE. FOR THIS REASON THE HEATER
MUST BE INSPECTED REGULARLY, DEPENDING ON CONDITIONS AND AT LEAST AT YEARLY INTERVALS.
8.1 PARTIALLY REFLECTIVE GLASS CLEANING
The partially reflective glass is cleaned in the factory during the assembly operation. During shipment,
installation, handling, etc., the partially reflective glass may collect dust particles; these can be removed by
dusting lightly with a clean dry cloth.
To remove fingerprints or other marks, the partially reflective glass can be cleaned with a damp cloth. The
partially reflective glass should be completely dried with a lint-free cloth to prevent water spots. To prevent
scratching, do not use abrasive cleaners.
8.2 CLEANINGGLASS DOOR
Use only a damp cloth to clean glass door of the fireplace. Do not use abrasive cleaners.
8.3 SERVICING
Except for installation and cleaning described in this manual, an authorized service representative should
perform any other servicing.

626-328-6324
MAIN POWER BUTTON
REFLECTOR
11
12
CHP-001
CHP-002
CHP-003
CHP-004
CHP-005
CHP-006
CHP-007
CHP-008
CHP-009
CHP-010
CHP-011
CHP-012
17
1
2
3
4
5
6
7
8
9
10
11
12
13
13 CHP-013 STAND
9.0 REPLACEMENT PARTS

10.0 WARRANTY
18
CAESAR FIREPLACE
Simply provide your proof of purchase along with the model and serial number to make a warranty claim. CAESAR FIREPLACE® reserves the
right to have its representative inspect any product or part thereof prior to honoring any warranty claim. Provided that the purchase was made
through an authorized CAESAR FIREPLACE® dealer your appliance is subject to the following conditions and limitations:
Warranty coverage begins on the date of original installation.
This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
Installation must be done in accordance with the installation instructions included with the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed
from other manufacturers will nullify this warranty.
In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship
provided that the product has been operated in accordance with the operation instructions and under normal conditions.
CAESAR FIREPLACE® will not be responsible for installation, labor or any other expenses related to the reinstallation of a warranted part and such
expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited Warranty, CAESAR FIREPLACE’s
responsibility under this warranty is defined as above and it shall not in any event extend to any incidental, consequential or indirect damages.
This warranty defines the obligations and liability of CAESAR FIREPLACE® with respect to the CAESAR FIREPLACE® electric appliance and
any other warranties expressed or implied with respect to this product, its components or accessories are excluded. CAESAR FIREPLACE®
neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.
Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging
chemicals or cleaners will not be the responsibility of CAESAR FIREPLACE®.
CAESAR FIREPLACE® reserves the right to have its representative inspect any product or part thereof prior to honoring any warranty claim.
All parts replaced under the Limited Warranty Policy are subject to a single claim.
All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.
Defects must be brought to the attention of Caesar Fireplace Technical Service by contacting Caesar F replace [phone], or 19295 E.
Walnut Dr N, City of Industry, CA 91748. Please have proof of purchase, catalogue/model available when calling. Limited warranty service
requires a proof of purchase of the product.
The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned
products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or
replace such defect.
Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without
authorization will be refused and returned to sender.
Shipping costs are not covered under this warranty.
Additional service fees may apply if you are seeking warranty service from a dealer.
® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary.
i
CAESAR FIREPLACE® electric appliances are manufactured under the strict Standard of the world recognized
ISO 9001:2008 Quality Assurance Certificate.
CAESAR FIREPLACE
who take great pride in their work. Once assembled the complete appliance is thoroughly inspected by a qualified technician
before packing to ensure that you, the customer, receive the quality product that you expect from CAESAR FIREPLACE®.
® products are designed with superior components and materials, assembled by trained craftsmen
Electrical components and wearable parts such as fan/heater, motors, nylon bearing components and remote controls
are covered and CAESAR FIREPLACE® will provide replacement parts free of charge during the first year of limited
warranty.
Light bulbs and fuses are NOT covered by the warranty.
Any labor related to warranty repair is not covered.
* Construction of models vary. Warranty applies only to components included with your specific appliance.
CAESAR FIREPLACE
ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS.
CAESAR FIREPLACE® IS A REGISTERED TRADEMARK OF CAESAR HARDWARE INTERNATIONAL LIMITED.