BCP SKY2970 User manual

SKY2970
Ver. 2
INSTRUCTION
MANUAL
Wall-Mounted or In-Wall
Electric Fireplace

Pg. 2
Pg. 2
Thank you for choosing us! Since 2002, Best
Choice Products has been bringing customers
high-quality products at the absolute lowest
price. With everything ranging from instruments
and toys to furniture and outdoor, we’ve got
your everyday living essentials covered. We’re
centered around a customer-first philosophy –
with free shipping, exceptional customer
service, and a catalog sourced with you in mind.

Pg. 3
Please retain these instructions for future reference.
SAFETY
The following safety hazards may result in serious injury or death:
• Please retain these instructions for future reference.
• Please read through all instructions before mounting and using this fireplace.
• This product should be wall-mounted at least 1 ft. above the ground. A 2 ft. height is recommended.
• There should be at least 3.5 ft. clearance between this product and the ceiling.
• The wall bracket on this product should only be fit horizontally.
• The cable should only be routed to the bottom right of the heater.
• Only use this heater with an AC power supply with the correct voltage.
• Do not plug in other devices into the same circuit.
• Do not turn the appliance on until it is properly installed.
• Do not leave appliance unattended during use or when plugged in.
• Do not let children operate or go near this appliance.
• Do not let children or small pets near during mounting and installation.
• Do not operate this product if the cord or any parts of this appliance are damaged. Do not attempt
to modify the cord.
• Periodically check the cord and appliance for damage.
• Do not run cord under rugs, furniture, etc.
• Do not allow cord to hang over sharp edges or place near hot surfaces.
• Do not cover or obstruct the heater in any way.
• Never immerse this appliance or cord in water or any other liquids.
• Do not attempt to replace the LED bulbs. Only a licensed and qualified electrician should do so.
• Repairs to this appliance should only be performed by a licensed and qualified electrician.
• Do not attempt to open the back panel unless the electricity is turned o.
• Disconnect and discontinue use of this appliance if any water damage occurs, or if the unit becomes
hot to the touch, broken, or smokes/smells like smoke.
• Do not dispose of this appliance as unsorted waste. Use special collection facilities for
electrical appliances.
NOTE: When the heat function is turned on for the first time, a slight odor may be present. This is
normal and should not occur again.
SPECIFICATIONS
Power Supply
Rated Power
120 V/60 Hz
500 W/1500 W

Pg. 4
APPROXIMATELY
45 MIN.
45LY
1 PERSON
ASSEMBLY APPROXIMATELY
45 MIN.
ASSEMBLY
2 PERSON
ASSEMBLY
PHILLIPS
SCREWDRIVER ELECTRIC DRILL
TOOLS REQUIRED
PARTS
HARDWARE
1
6 PCS
2
6 PCS
3
6 PCS
4
2 PCS
A
D
B C
1 PC
1 BAG
1 PC 1 PC
WALL-MOUNTING
BRACKET
E
1 PC
WHITE PLATFORM
HEATER REMOTE CONTROL
CRYSTAL STONES
#6 DRILL BIT

Pg. 5
• Mark the location where the screws will go on the wall. NOTE: Do not ax this appliance at a height
lower than 1 ft. from the floor (at least 2 ft. recommended), or higher than 3.5 ft. from the ceiling.
• Drill the holes for the screws with a No. 6 drill bit.
NOTE: It is recommended to use a level to ensure holes are drilled at an even height.
Insert five part 3 wall anchors into the
drilled holes.
Attach the part A wall bracket to the wall
anchors with five part 2 screws.
Carefully lift and secure the part B
heater to the wall bracket, ensuring
the top ledge of heater connects with
and is centered with the wall bracket.
Attach the sides of the wall bracket to
the heater with two part 1 screws, one
on each side.
WALL
WALL
TOOLS REQUIREDWALL MOUNT ASSEMBLY
1
2
A3
2
B
1
1

Pg. 6
Unscrew the tempered glass from part B
heater. Gently push glass up and slide it o
the lugs that hold it onto the fireplace.
Insert 6 part 3 wall anchors into the
drilled holes.
Place fireplace into wall and secure it
with six part 2 screws.
1
TOOLS REQUIREDIN-WALL ASSEMBLY
2
2
2
3
3
B
WALL

Align the tempered glass over
the front of the unit. Make
sure the slots in the bracket
on the sides of the glass
panel align with the lugs on
the side of the heater.
Carefully lower the tempered
glass onto the lugs and
secure it to the heater with
the screws that was
previously removed, one on
each side.
Pg. 7
2
Remove glass to open front of unit.
Remove the carbon log via unscrewing
screws on both sides.
IN-WALL ASSEMBLY
INSTALLING CRYSTAL STONES (OPTIONAL)
1
3
WALL

Pg. 8
INSTALLING CRYSTAL STONES
Remove plastic film lamination
from part E.
Slide part 4 platform brackets onto
part E white platform.
Install the part E white platform
using the same screws from carbon
log (one on each side) and four
part 1 screws to base of heater.
Arrange the part D crystal stones
on the part E white platform.
22
2
3
4
4
E
1
1
E
D

Pg. 9
HEATER/FIREPLACE OPERATION
CONTROL PANEL
INSTALLING CRYSTAL STONES
• This appliance has a safety-cut o that will engage if the fireplace overheats. The fireplace
will NOT automatically reset for safety reasons. To reset the appliance, unplug the unit for
15 minutes and then plug it back in.
• This appliance can be controlled by the panel on the unit or the remote.
• Do not press the buttons more than once in two seconds; it takes some time for the
fireplace to respond.
ON/OFF: Turn the heating/display eect on and o.
DIMMER: Controls the brightness levels. Press to cycle through 5 dimness levels and the OFF setting.
HEAT 1/HEAT 2: Controls the heating level. Press to cycle through the low setting (500W), high setting
(1500W), and the OFF setting.
Replace glass and secure again with the two screws
that was previously removed.
ON/OFF DIMMER HEAT 1
HEAT 2
24

RELEASE
ON/OFF
DIMMER HEAT
Pg. 10
REPLACING BATTERIES
The remote has a 3V CR2025 lithium cell battery included. Remove the slip between the
battery and contacts before operating the remote.
DIMMER: Adjust dimmer settings
HEAT: Adjust heat settings
REMOTE CONTROL OPERATION
• Press the release and slide open the back panel of the remote.
• Remove the battery.
• Insert a brand new CR2025 battery, ensuring the “+” and “-“ signs are in the correct order.
• Replace back panel.

• Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Do not put batteries next to or in a heat source (fire, electronic heating device, etc.).
• Do not hit batteries against hard objects.
• Do not submerge batteries in water.
• Batteries should be inserted with the correct polarity.
WARNINGS REGARDING BATTERIES
• Turn unit o and unplug before any maintenance. Wait at least 10 minutes after
unplugging before cleaning or maintenance.
• Use a vacuum/duster to keep vent area and heater clear of debris and dust.
• Fireplace exterior should be cleaned with a damp cloth or duster.
• Do not use abrasive cleaners or liquids.
CARING FOR YOUR HEATER
Pg. 11

All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the
item is returned in its original product packaging and all accessories from its original shipment are included. All
returned items will receive a full refund back to the original payment method. All returned items will not be charged
a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best Choice
Products Customer Service Representative when the return request is submitted. Items received without an RA
may not be accepted or may increase your return processing time. Once an item has been received by Best Choice
Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer’s expense. If the
reason for return is a result of an error by Best Choice Products then Best Choice Products will provide a pre-paid
shipping label via email. Boxes for return shipping will not be provided by Best Choice Products, and is the
customer’s responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are
not considered undamaged until they are received by Best Choice Products and verified as such. All damages to
items are the customer’s responsibility until the item has been received by and acknowledge by Best Choice
Products as undamaged.
CONTACT US; WE’RE HERE 7 DAYS A WEEK TO HELP YOU!
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or
loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
PRODUCT WARRANTY INFORMATION
bestchoiceproducts.com customerservice@
bestchoiceproducts.com 844.948.8400 LEARN MORE!
ASSEMBLY IS COMPLETE!