BE Ag & Industrial BE-LS22TL Application guide

PURCHASE DATE MODEL NO. SERIAL NUMBER
DEALER
LOG SPLITTER
BE-LS22TL
BE-LS28TL
BE-LS34TL
OPERATIONS & PARTS MANUAL

2 BE-LSxxTL USER MANUAL
TABLE OF CONTENTS
3IMPORTANT SAFETY INFORMATION
4SAFETY DECALS
5SAFETY INFORMATION
7PRE-OPERATION
12 UNPACKING THE CONTAINER
14 ASSEMBLY
21 SET-UP
23 OPERATION
27 MAINTENANCE & ADJUSTMENTS
29 TROUBLESHOOTING
30 SPECIFICATIONS
31 BREAKDOWN
34 PACKING LIST
INTRODUCTION
Thank you for purchasing a BE Log Splitter. It was carefully engineered to provide excellent performance
when properly operated and maintained.
Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set
up, operate and maintain your machine. Please be sure that you, and any other persons who will operate
the machine, carefully follow the recommended safety practices at all times. Failure to do so could result in
personal injury or property damage.
All information in this manual is relative to the most recent product information available at the time of
printing. Review this manual frequently to familiarize yourself with the machine, its features and operation.
Please be aware that this Operator’s Manual may cover a range of product specifications for various models.
Characteristics and features discussed and/or illustrated in this manual may not be applicable to all models.
We reserve the right to change product specifications, designs and equipment without notice and without
incurring obligation.
If applicable, the power testing information used to establish the power rating of the engine equipped on
this machine can be found at the engine manufacturer’s manual or website.
Throughout this manual, all references to right and left side of the machine are observed from the operating
position. The engine manufacturer is responsible for all engine-related issues with regards to performance,
power-rating, specifications, warranty and service. Please refer to the engine manufacturer’s Operations &
Parts Manual, packed separately with your machine, for more information.

BE-LSxxTL USER MANUAL 3
IMPORTANT SAFETY INFORMATION
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals before
assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow
anyone can be dangerous if assembled or used improperly. Do not operate this log splitter if you have any
questions concerning safe operation.
This SAFETY ALERT SYMBOL identifies important safety messages in this manual. Failure
to follow this important safety information may result in serious injury death.
DANGER
This machine was built to be operated according to the safe operation practices in this manual. As with
any type of power equipment, carelessness or error on the part of the operator can result in serious
injury. This machine is capable of amputating hands and feet and throwing debris.
Failure to observe the following safety instructions could result in serious injury or death.
The following signal words and meanings are intended to explain the levels of risk associated with this
product:
DANGER
Indicates a hazardous situation which, if not followed, will result in serious injury or death.
WARNING
Indicates a hazardous situation which, if not avoided, could result in serious injury or death.
CAUTION
Indicates a hazardous situation which, if not followed, could result in minor to moderate injury.
NOTICE
Is important information about the proper use of your machine.
Failure to follow this instruction could result in damage to your machine or property.
CALIFORNIA PROPOSITION 65
WARNING:
Engine Exhaust, some of its constituents and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and birth defects or other reproductive harm.

4 BE-LSxxTL USER MANUAL
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable.
Always replace missing or defaced decals. Contact an authorized service dealer for replacement decals.

BE-LSxxTL USER MANUAL 5
SAFETY INFORMATION
This page depicts and describes safety symbols that may appear on this product. Read, understand and
follow all instructions on the machine before attempting to assemble and operate.
WARNING
Your Responsibility - Restrict the use of this power machine to persons who read, understand and follow the
warnings and instructions in this manual and on the machine.

6 BE-LSxxTL USER MANUAL
TRAINING
• Read, understand and follow all instructions on the machine and in the manual(s) before attempting to
assemble and operate. Keep this manual safe place for future and regular reference and for ordering
replacement parts.
• Be familiar with all controls and their proper operation. Know how to stop the machine and disengage
them quickly.
• Never allow children under 18 years of age to operate this machine. Children 16 and over should read and
understand the instructions and safe operation practices in this manual and on the machine and be trained
and supervised by an adult.
• Never allow adults to operate this machine without proper instruction.
• Many accidents occur when more than one person operate the machine. No helpers is allowed to assist in
stacking logs.
• Keep bystanders, pets and children at least 25 feet from the machine while it is in operation.
• Never allow anyone to ride on this machine.
• Never transport cargo on this machine.
• Hydraulic log splitters develop high fluid pressures during operation. Fluid escaping through a pin hole
opening can penetrate your skin and cause blood poisoning, gangrene or death. Give attention to the
following instructions at all times:
1) Do not check for leaks with your hand.
2) Do not operate machine with frayed, kinked, cracked or damaged hoses, fittings or tubing.
3) Stop engine and relieve hydraulic system pressure by cycling the valve control lever from forward to
reverse several times while engine is not running; returning to neutral before repairing or adjusting
fittings, hoses, tubing or other system components.
4) Do not adjust the pressure settings of the pump or valve.
• Leaks can be detected by passing cardboard or wood, while wearing protective gloves and safety glasses,
over the suspected area. Look for discoloration of cardboard or wood.
• If injured by escaping fluid, see a doctor immediately. Serious infection or reaction can develop if proper
medical treatment is not administered immediately.
• Keep the operator zone and adjacent area clear for safe, secure footing.
• If your machine is equipped with an internal combustion engine and is intended for use near any
unimproved forest, brush or grass covered land, the engine exhaust should be equipped with a spark
arrestor. Make sure you comply with applicable local, state and federal codes. Take appropriate firefighting
equipment with you.
NEVER
Use this log splitter for any purpose other than splitting wood, It is designed for this use can cause
serious injury or death.

BE-LSxxTL USER MANUAL 7
WARNING
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool, always wear safety goggles or safety glasses
with side shields and when needed, wear a full-face shield and earplugs. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection marked to comply with ANSI Z87.1.
PRE-OPERATION
• BEFORE operating this log splitter, make sure that you wear safety goggles or safety glasses, steel toed
shoes and tight-fitting gloves (without loose cus or draw strings). Always wear a protective hearing
device when operating this log splitter.
• NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing
and hair away from all moving parts when operating this log splitter.
• Check all safety guards and shields to be sure they are in the proper position. Never operate with safety
guards, shields or other protective features removed.
• Make sure machine is on a flat, dry, solid ground before operating.
• ALWAYS operate your log splitter in an open area. (Exhaust fumes contain carbon monoxide which can be
deadly when inhaled).
• ALWAYS operate your log splitter in daylight or under good artificial light.
• ALWAYS operate your log splitter on level ground. (Operating on a slope could cause the log splitter to roll
over or logs to fall o).
• ALWAYS block wheels to prevent unintended movement.
• ALWAYS keep the work area clean. Remove split wood around the log splitter immediately so that you
don’t stumble over it.
• Check all nuts, bolts and hydraulic fittings are tight to be sure the equipment is in a safe working condition.
• Both ends of the log should be cut as square as possible to help prevent the log from riding out of the
splitter during operation. Do not split logs greater than 20.5 inches in length. Uneven logs (e.g., knotted,
curved, etc.) should not be used.
• ALWAYS check the oil level before you start the log splitter.
• Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is
sucient to inflict serious injury.

8 BE-LSxxTL USER MANUAL
• BEFORE starting this machine, review the safe instructions in the manual. Failure to follow these rules may
resulting in serious injury to the operator or bystanders.
• NEVER leave this machine unattended with the engine running.
• DO NOT operate machine while under the influence of alcohol, drugs or medication.
• NEVER allow anyone to operate this machine without proper instruction.
• ALWAYS operate this machine with all safety equipment in place and working, make sure all controls are
properly for safe operation.
• When loading a log, always place your hands on the side of the log, not on the ends and never use your
foot to help stabilize a log. Failure to do so may result in crushed or amputated fingers, toes, hand or foot.
• NEVER use your foot, a rope or any extension device to operate the control lever on the valve. Only use
hand.
• Use only your right hand to operate the controls.
WARNING
When stabilize log with left hand, remove your hand when the wedge just contacts the log or serious
injury may occur.
• For logs which are not cut square, the least square end of the log should be placed toward the beam
andwedge, and the square end placed toward the end plate.
• NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke as this
could result in serious injury or death. NEVER attempt to load the log splitter when the ram or wedge is in
motion.
• ALWAYS Keep fingers away from any cracks that open in the log while splitting. They can quickly close and
pinch or amputate your fingers.
• Keep your work area clean. Immediately remove split wood around the machine so you don’t stumble over
it.
• NEVER straddle or step over the log splitter during operation.
• NEVER reach or bend over the log splitter to pick up a log.
• NEVER try to split two logs on top of each other. NEVER try to cross split a log.
• NEVER operate your log splitter when it is poor mechanical condition or in need of repair.
• NEVER touch the muer and other hot areas of the engine during operation. Wait until the engine cools
down.
• NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the
manufacturer and is within limits. Refer to the engine owner’s manual for your particular log splitter.
• NEVER move the log splitter while the engine is running. Shut o the engine if you are leaving the log
splitter, even for a short period of time.
• ALWAYS be careful when moving or lifting the log splitter. Get assistance if it feels too heavy to move
• yourself by yourself.

BE-LSxxTL USER MANUAL 9
OPERATOR ZONE
ONLY operate the log splitter from the operator zones as shown in the diagram below. The operator has the
safest and most ecient access to the control valve and the beam in this location. Operating the log splitter
in another location can result in serious injury or death. (See Figure 1).
Horizontal Operating Position: stand on the control lever side of the log splitter and stabilize log as shown.
See Figure 1.
Vertical Operating Position: stand on the control lever side of the log splitter and stabilize log as shown.
See Figure 2.

10 BE-LSxxTL USER MANUAL
MAINTENANCE SAFETY
• Stop the engine, disconnect the spark plug and ground it against the engine before cleaning or inspecting
the machine.
• NEVER perform any service or repair on your log splitter without first removing the spark plug wire.
• Stop the engine and relive hydraulic system pressure by cycling the valve control lever from forward to
reverse several times while engine is not running; returning to neutral before repairing or adjusting fittings,
hoses, tubing or other system components.
• ALWAYS perform all recommended maintenance procedures before using your log splitter.
• ALWAYS check the level of hydraulic oil and engine oil before operation.
• ALWAYS periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamp are tight to be
sure equipment is in safe working condition.
• ALWAYS replace all damaged or worn parts immediately with original equipment manufacturer’s (O.E.M.)
parts only. Use of parts which do not meet the original equipment specifications may lead to improper
performance and compromise safety.
• The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be
sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.
• NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost
invisible. Escaping fluid under pressure can have sucient force to penetrate skin causing SERIOUS
INJURY or even DEATH. Leaks can be safely detected by passing a piece of cardboard over the suspected
leak and looking for discoloration.
• NEVER remove the cap from hydraulic tank or reservoir while the log splitter is running. The tank could
contain hot oil under pressure which could result in serious injury.
• NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is pre-set at the factory.
Only a qualified service technician should perform this adjustment.
• ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious
infection or reaction can develop if proper medical treatment is not administered immediately.
• ALWAYS be sure to relieve all pressure by shutting o the engine and moving the valve control handle back
and forth should it become necessary to loosen or remove any hydraulic fitting.
NEVER
Alter your log splitter in any manner. Such alterations may cause your log splitter to be unsafe and will
void the warranty.
According to the Consumer Products Safety Commission (CPSC) and the U.S. Environmental Protection
Agency (EPA), This product has an Average Useful Life of seven (7) years, or 130 hours of operation. At
the end of the Average Useful Life have the machine inspected annually by an authorized service dealer
to ensure that all mechanical and safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.

BE-LSxxTL USER MANUAL 11
SPARK ARRESTOR
WARNING
This log splitter is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is
equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used,
it should be maintained in eective working order by the operator. In the State of California, a spark
arrester is required by law. Other states have similar laws. Federal laws apply on federal lands. A spark
arrester muer is optional and available as an accessory at your nearest engine dealer. Always check
the legal requirements in your area.
FIRE PREVENTION
• ALWAYS take a Class B fires extinguisher with when operating this log splitter in dry areas.
• NEVER operate your log splitter near a flame or spark or smoke during operation. Extinguish all cigarettes,
cigars, pipes and other sources of ignition. Hydraulic oil and gasoline are flammable and can explode.
• To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
• ALWAYS store gasoline in an approved, tightly sealed container and keep away from heating appliances.
Store the container in a cool, dry place.
• When gasoline is spilled on yourself or your clothes which can ignite wash your skin and change clothes
immediately.
• NEVER refuel the gas tank while the engine is hot or running. Allowing the engine to cool before refueling.
• ONLY refuel your log splitter in a clear area with no gas fumes or spilled gas. Never fuel machine indoors.
• Never overfill the fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space
for fuel expansion.
• If gasoline is spilled out, wipe it o the engine & equipment and move machine to another area. Wait five
(5) minutes before starting engine.
• ALWAYS replace the gas cap securely. Never remove gas cap while the engine is hot or running.
• To prevent fires, clean debris and cha from the engine and muer area.
• Allow machine to cool at least ten (10) minutes before storing.
• ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
• Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a
water heater, furnace, clothes dryer or other gas appliances.
• If the engine is equipped with a spark arrestor muer, clean and inspect it regularly according to
manufacturer’s instructions. Replace if damaged.

12 BE-LSxxTL USER MANUAL
TOWING SAFETY
• NEVER carry any cargo or wood on your log splitter.
• NEVER allow anyone to sit or ride on your log splitter.
• ALWAYS turn the fuel shaft o valve on the engine to the “OFF” position before towing the log splitter.
Failure to do so may result in flooding the engine.
• ALWAYS confirm coupler tightness each time before towing and after towing 50 miles.
• ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the
towing vehicle and that the safety chains are secured to the hitch or bumper of the vehicle with enough
slack to allow turning. Always use a Class 1, 2” ball with this log splitter.
• NEVER exceed weight capacity of ball or load limits of coupler. ALWAYS replace ball or coupler if
damaged.
• NEVER exceed 45 MPH when towing your log splitter. Towing the log splitter at speeds higher than 45 MPH
could result in loss of control, damage to the equipment, or serious injury or death. Adjust towing speed for
terrain and conditions.
• ALWAYS be careful when backing up with your log splitter in tow. IT could jackknife.
• ALWAYS allow for added length of your log splitter when turning, parking and crossing intersections and in
all driving situations.
• ALWAYS use safety chains when towing your log splitter.
• Be extra cautious when towing over rough terrain, especially railroad crossings and avoid sharp turns and
steep angles when towing your log splitter.
• Never attempt to move this machine over hilly or uneven terrain without a tow vehicle or adequate help.
• ALWAYS disconnect your log splitter from the towing vehicle before operating it.
• ALWAYS check all local and state regulations regarding towing, licensing and lights before towing your log
splitter.
This machine should not be towed on any street, highway or public road without checking the existing
federal, state or local vehicle requirements. Any licensing or modifications, such as taillights, etc., needed
to comply, is the sole responsibility of the purchaser. If a “Statement of Origin” is required in your state, see
your local dealer.
UNPACKING THE CONTAINER
WARNING
Indicates a hazardous situation which, if not avoided, could result in serious injury or death.
NOTE: All references in this manual to the left or right side and front or back of the log splitter are from the
operating position only. Exceptions, if any, will be specified.
Unpacking Tools Needed:
1. Wrench 14mm
2. Scissors or knife
3. Pry bar or claw hammer
Step 1: Use a 14mm wrench to remove all the bolts and washers on the metal crate, put aside the packing
top and side frames, then remove the cardboard box. See Figure 3.
Step 2: Remove all loose parts included in the container, e.g., hardware box.
Step 3: Use scissors or a knife to cut and remove the straps securing the parts to the beam or tank assembly,
including fenders, wheels, tongue assembly, log tray assemblies, then put aside these parts for assembly.

BE-LSxxTL USER MANUAL 13
NOTE: DO NOT remove the strap securing the hydraulic hose assemblies to the beam at this time, until you
do the assembly procedure of the hoses.
Step 4: Use a pry-bar or claw hammer to remove the plywood splinters securing the beam and tank
assemblies on the crate bottom. Take out the two assemblies.
Step 5: Inspect all component assemblies, parts and accessories according to the packing list attached in the
back of this manual.
If any parts are damaged or missing, please call the authorized service dealer for assistance.
NOTE: DO NOT discard the packing materials until you have carefully inspected and satisfactorily operated
the tool.

14 BE-LSxxTL USER MANUAL
ASSEMBLY
NOTE: Due to the weight/size of the log splitter, it is recommended that two or more adults be present to
assist with the assembling. Some lifting tools as hoist, crane, jack, etc. are recommended.
Step 1: Assemble the fenders to the reservoir assembly. See Figure 4.
REF DESCRIPTION QTY
1 Reservoir Tank Assembly 1
2 Fender 2
3-1 Fender Support (Hardware Kit #1) 2
3-2 Hex Head Bolt - M8x25 (Hardware Kit #1) 8
3-3 Flat Washer - M8 16
3-4 Lock Nut - M8 8
Step 2: IAttach the two wheels to the tank assembly wheels spindles. See Figure 5.

BE-LSxxTL USER MANUAL 15
REF DESCRIPTION QTY
4 Road-Speed Tire & Wheel 2
5-1 Castle Nut - 1-1/4 (Hardware Kit #2) 2
5-2 Split Pin - Ø4x35 (Hardware Kit #2) 2
5-3 Hub Cap (Hardware Kit #2) 2
Step 3: Attach the tongue and jack stand assembly to the reservoir assembly.
1. Remove the spring clip (Ø3) and clevis pin (Ø6x50) from the jack stand on the tongue, then pivot the jack
stand towards the ground into the operating position. Secure the jack stand in position with the clevis pin
and spring clip just removed. See Figure 6.
2. Attach the horizontal beam lock to the tongue, then attach the tongue to the reservoir assembly.
See Figure 7.
REF DESCRIPTION QTY
6 Tongue & Jack Stand Assembly 1
7-1 Horizontal Beam Lock (Hardware Kit #3) 1
7-2 Hex Head Bolt - M10x80 (Hardware Kit #3) 4
7-3 Flat Washer - M10 (Hardware Kit #3) 8
7-4 Lock Nut - M10 (Hardware Kit #3) 4

16 BE-LSxxTL USER MANUAL
Step 4: Attach the engine assembly to the engine mount plate on the reservoir assembly. See Figure 9.
Step 4: Assemble the pump assembly to the engine. See Figure 8.
1. Loosen the set screw on the coupler at the engine side.
2. Place the engine shaft key into the slot on the engine shaft.
3. Insert the engine shaft into the center hole of coupler, pivoting the pump assembly to ensure the engine
shaft key to fit in the slot of the coupler center hole. Then tighten the set screw just loosened.
4. Rotate the engine shaft to align the fixing holes on both pump mount and engine, ensure the open side of
the pump mount facing down as shown in the illustration below, then screw on the hardware and tighten.
REF DESCRIPTION QTY
8-1 Engine (Engine Assembly) 1
8-2 Engine Shaft Key (Engine Assembly) 1
9-1 Two Stage Pump Assembly (Hardware
Kit #4) 1
9-2 Hex Head Bolt - 5-16-24 (Hardware Kit
#4) 4
9-3 Spring Washer - 5/16 (Hardware Kit
#4) 4
9-4 Flat Washer - 5/16 (Hardware Kit #4) 4
REF DESCRIPTION QTY
10-1 Hex Head Bolt - M8x40 (Hardware Kit #5) 4
10-2 Flat Washer - M8 (Hardware Kit #5) 8
10-3 Lock Nut - M8 (Hardware Kit #5) 4

BE-LSxxTL USER MANUAL 17
Step 6: Assemble the beam. See Figure 10.
1. Stand the beam up on end. Two or more people may be needed for this step to ensure safety.
Make sure that the beam is stable and on a level surface.
2. Remove the clevis pin and spring pin from the tank brackets. Roll the tongue/tank assembly into position
between the two tabs on the beam, Slide the clevis pin through the aligned holes and lock in place with
the spring clip.
REF DESCRIPTION QTY
11 Beam Assembly 1
WARNING
Take extra care when raising and lowering the beam as it is fairly heavy.
Having a second person assist with raising or lowering the beam is recommended.
Be sure to keep hands away from any possible pinch points.

18 BE-LSxxTL USER MANUAL
Step 7: Connect the open ends of the hydraulic hoses to their corresponding fittings. See Figure 11.
There are three hydraulic hoses listed below, each of them has one end fixed on the link part assembly at the
manufacturer’s field, the other open end needs you to attach. For clear view of the hydraulic hoses, the hose
protective springs are not shown in the illustration below.
1. Oil suction hose / Ø25x310mm, labeled as (1), comes from the tank.
Loosen the hose clamp /Ø30 on the open end of this hose, then connect the hose to the fitting on the
bottom of the pump, which is labeled of a same (1). Tighten the hose clamp.
2. Pump/Valve connecting hose/Ø19x900mm, labeled as (2), comes from the bottom of the valve.
Screw the open end of this hose onto the fitting on top of the pump, which is labeled of a same (2).
3. Oil return hose/Ø19x1500mm, labeled as (3), comes from the top of the valve.
Loosen the hose clamp/Ø25 on the open end of this hose, then connect the hose to the fitting on the
filter, which is labeled of a same (3). Tighten the hose clamp.

BE-LSxxTL USER MANUAL 19
Step 8: Assemble the log dislodger and log tray. See Figure 12.
1. Attach the log tray to the beam and log dislodger to its link part (see highlighted parts in illustration
below).
You could perform this procedure with the beam in horizontal or vertical position.
Step 9: Assemble the control handle. The control handle is shipped hanging from the valve on the handle
link. See Figure 13.
1. Remove the clevis pin and bow-tie cotter pin from the control handle.
2. Rotate the control handle into the operating position and secure with the clevis pin and bow-tie cotter pin
removed in step above.
REF DESCRIPTION QTY
12 Log Tray & Log Dislodger Assembly 2
13-1 Hex Head Bolt - M12x45 (Hardware Kit #6) 4
13-2 Flat Washer - M12 (Hardware Kit #6) 1
13-3 Lock Nut - M12 (Hardware Kit #6) 1
13-4 Hex Head Bolt - M10x35 (Hardware Kit #6) 1
13-5 Flat Washer - M10 (Hardware Kit #6) 1
13-6 Lock Nut - M10 (Hardware Kit #6) 1

20 BE-LSxxTL USER MANUAL
REF DESCRIPTION QTY
14-1 Cross Wedge 1
14-2 L-Shape Support 2
14-3 Hex Head Bolt - M8x55 1
14-4 Lock Nut - M8 1
14-5 Hex Head Bolt - M8x25 2
14-6 Spring Washer - M8 2
14-7 Flat Washer - M8 2
GAS OIL FILL-UP
Service the engine with gasoline and engine oil as instructed in the engine manual packed with your log
splitter. Read the instructions carefully.
WARNING
Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
Never fuel the machine indoors or while the engine is hot or running.
NOTE:
Your log splitter may be shipped without engine oil. You must check the oil level before operating. Be careful
not to overfill. Gasoline can be added to the engine when the log splitter is in either the horizontal or vertical
position. However, it may be easier when the splitter is in the vertical position.
TIRE PRESSURE
The max recommended operating pressure is 30 psi. Under any circumstances do not exceed the
manufacturer’s recommended psi. Maintain equal pressure on all tires.
WARNING
Excessive pressure when seating beads may cause tire/rim assembly to burst with force sucient to
cause serious injury.