Champion Power Equipment 92251-1 User manual

OWNER’S MANUAL
22 Ton
LOG SPLITTER
12039 Smith Ave.
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV 92251-1-20161116
92251-1
MODEL NUMBER

Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
AN IMPORTANT MESSAGE ABOUT TEMPERATURE:
Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to
40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to
50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be
brought back within this range before operation. In any event, the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and other vents.
Parts Ordering:
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999

92251-1
TABLE OF CONTENTS
22 Ton
LOG SPLITTER
Introduction ............................ 1
Manual Conventions....................... 2
Safety Rules ............................ 3
Training ............................. 5
Preparation .......................... 5
Operation ............................ 6
Maintenance and Storage ................. 6
Controls and Features ..................... 7
Log Splitter .......................... 7
Assembly .............................. 8
Open Shipping Crate .................... 8
1) Install the Tow Bar ................... 8
2) Install the Wheels.................... 8
3) Install the Beam ..................... 8
4) Install the Cylinder and Wedge ........... 9
5) Install the Oil Filter................... 9
6) Install the Engine and Hoses ........... 10
Add Hydraulic Oil ..................... 10
Add Engine Oil ....................... 11
Add Engine Fuel ...................... 11
Operation ............................. 12
Before Each Use Inspect the Log Splitter ..... 12
Towing Log Splitter Safety ............... 12
Log Splitter Location ................... 12
Starting the Engine .................... 13
Stopping the Engine ................... 13
Log Splitter Operation .................. 14
Maintenance and Storage .................. 15
Engine Maintenance ................... 15
Oil ............................. 15
Spark Plugs ....................... 15
Air Filter ......................... 15
Changing the Hydraulic Oil and Oil Filter ... 16
Cleaning ......................... 17
Maintenance Schedule................ 17
Log Splitter Maintenance ................ 17
Storage ............................ 17
Log Splitter Storage ................. 17
Engine stored for Less than 30 Days ...... 17
Engines Stored for Over 30 Days......... 17
Troubleshooting......................... 19
Specifications .......................... 20
Log Splitter Specifications ............... 20
Engine Specifications .................. 20
Spark Plugs ......................... 20
Maintenance Valve Clearance ............. 20
Hydraulic Oil ........................ 20
Fuel .............................. 20
Oil ............................... 20
Parts Diagram........................ 21
Parts List ........................... 22
Engine Parts Diagram .................. 23
Engine Parts List ..................... 24

1
ENGLISH 92251-1
INTRODUCTION
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
Model Number
Serial Number
Date of Purchase
Purchase Location
1-877-338-0999
92251-1
For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.
Congratulations on your purchase of a Champion Power Equipment product. Champion Power Equipment and
Champion Engine Technology designs, builds, and supports all of our products to strict specifications and guidelines.
With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying
service.
Every effort has been made to ensure the accuracy and completeness of the information in this manual, and we
reserve the right to change, alter and/or improve the product and this document at any time without prior notice.
Since CPE/CET highly value how our products are designed, manufactured, operated and are serviced, and also
highly value your safety and the safety of others, we would like you to take the time to review this product manual
and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers
and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating
the product fully familiarize themselves too, with the proper safety and operation procedures before each use. Please
always exercise common sense and always error on the side of caution when operating the product to ensure no
accidents, property damage, or injury occurs. We want you to continue to use and be satisfied with your CPE/CET
product for years to come.

2
92251-1 ENGLISH
MANUAL CONVENTIONS
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
CAUTION
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
DANGER
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
WARNING
If you have questions regarding your log splitter, we can
help. Please call our help line at 1-877-338-0999
NOTE

3
ENGLISH 92251-1
SAFETY RULES
Log Splitter engine exhaust contains carbon
monoxide, a colourless. odourless, poison gas.
Breathing carbon monoxide will cause nausea,
dizziness, fainting or death. If you start to feel dizzy
or weak, get to fresh air immediately.
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories. Traumatic amputation or
severe laceration can result.
DANGER
DANGER
Operate log splitter outdoors only in a well
ventilated area. DO NOT operate the log splitter
inside any building, enclosure or compartment.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other
openings. DANGER CARBON MONOXIDE, using a
log splitter indoors CAN KILL YOU IN MINUTES.
Keep hands and feet away from rotating parts. Tie up
long hair and remove jewellery. Operate equipment
with guards in place. DO NOT wear loose-fitting
clothing, dangling drawstrings or items that could
become caught.
The engine exhaust from this product contains
chemicals known to the state of California to cause
cancer, birth defects, or other reproductive harm.
Read this manual thoroughly before operating your
log splitter. Failure to follow instructions could result
in serious injury or death.
WARNING
WARNING
Sparks can result in fire or electrical shock.
DANGER
When servicing the engine:
Disconnect the spark plug wire and place it where
it cannot contact the plug. DO NOT check for spark
with the plug removed. Use only approved spark
plug testers.
Running engines produce heat. Severe burns can
occur on contact. Combustible material can catch
fire on contact.
DO NOT touch hot surfaces. Avoid contact with
hot exhaust gases. Allow equipment to cool before
touching. Maintain at least 3 ft. (91.4 cm) of
clearance on all sides to ensure adequate cooling.
Maintain at least 5 ft. (1.5 m) of clearance from
combustible materials.
Crush Hazard
Wedge can cut through skin and break bones. Keep
all limbs away from wedge and endplate.
WARNING
WARNING
Projectile Hazard
Pieces of log may be ejected from the splitter while
operating. Wear ANSI approved safety glasses when
operating. Be alert.
WARNING
Keep Operator Work Zone Clear
Keep work zone clear of debris while working to
ensure safe footing.
WARNING
Before removing the pin installed into the front
support leg make sure hitch is installed onto vehicle.
Releasing the pin before will cause support leg to
slide up and possibly cause injury.
WARNING

4
92251-1 ENGLISH
SAFETY RULES
Skin Injection Hazard. High pressure hydraulic oil
can inject under your skin.
DANGER
Make sure all fittings are tightly secure before
applying pressure. Relieve system of pressure
before servicing.
Towing Hazard
ALWAYS check all local and state regulations
regarding towing, licensing and lights before towing
your log splitter. Review towing safety warnings in
your towing vehicle manual.
Drive safely. Be aware of the added length of the
log splitter. NEVER ride or transport cargo on the
log splitter. Choose a level surface to operate the
log splitter.
NEVER EXCEED MAX. Towing Speed 45 MPH (72
KPH)
WARNING
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
WARNING
Improper treatment or use of the log splitter can
damage it, shorten its life and void your warranty.
Use the log splitter only for intended uses. Operate
only on level surfaces. DO NOT expose log splitter
to excessive moisture, dust, or dirt.
DO NOT allow any material to block the cooling
slots. DO NOT use the engine if:
– Equipment sparks, smokes or emits flames
– Equipment vibrates excessively
CAUTION
Parts of the hydraulic circuit (cylinder, pump, valve-
body, hoses) can become very hot during operation.
CAUTION
Fuel and fuel vapours are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
When adding or removing fuel:
Turn the engine off and let it cool for at least two
minutes before removing the fuel cap. Loosen the
cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the log splitter
at the gas station. Use an approved container to
transfer the fuel to the log splitter.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the engine:
DO NOT attempt to start a damaged engine.
Make certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in place.
Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the log splitter is resting firmly on
level ground.
When operating the log splitter:
DO NOT move or tip the log splitter during
operation.
DO NOT tip the log splitter or allow fuel or oil to
spill.
Block the tires to prevent unintended movement.
When transporting or servicing the log splitter:
Make certain that the fuel shutoff valve is in the off
position and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the log splitter:
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
DANGER

5
ENGLISH 92251-1
SAFETY RULES
Training
1. Read the Operator’s Manual completely before
attempting to use this log splitter.
2. Do not allow anyone to operate your log splitter who
has not read the Operator’s Manual or has not been
instructed on the safe use of the log splitter.
3. Never allow children or untrained adults to operate
this machine.
4. Many accidents occur when more than one (1)
person operates the log splitter. If a helper is
assisting in loading logs to be split, never actuate
controls until helper is clear of the area.
5. Never allow anyone to ride on the machine.
6. Never transport cargo on the log splitter.
7. High fluid pressures are developed in hydraulic
log splitters. Pressurized hydraulic fluid escaping
through a pin hole opening can puncture skin
and cause sever blood poisoning. Therefore, the
following instructions should be heeded at all times.
a. Do not operate the unit with frayed, kinked,
cracked or damaged hoses, fittings, or tubing.
b. Stop the engine and relieve hydraulic system
pressure before changing or adjusting fittings,
hoses, tubing, or other system components.
c. Do not adjust the pressure settings of the pump
or valve.
d. Do not check for leaks with your hand. Leaks
can be detected by passing cardboard or wood
over the suspected area. Look for discolouration.
If injured by escaping fluid, see a doctor at
once. Serious infection or reaction can develop
if proper medical treatment is not administered
immediately.
8. Keep the operator zone and adjacent area clear for
safe, secure footing.
9. If your log splitter is equipped with an internal-
combustion engine and intended for use near any
unimproved forest, brush, or grass covered land,
the engine exhaust should be equipped with a spark
arrestor. Make sure you comply with local, state,
and federal codes. Take appropriate fire-fighting
equipment with you.
10. Log splitters should be used only for splitting
wood. Do not use for other purposes unless the
manufacturer provides attachments and instructions.
Preparation
1. Be thoroughly familiar with all controls and with
proper use of the equipment.
2. Safety Gear:
a. Always wear safety shoes or heavy boots when
operating the machine.
b. Always wear safety glasses or goggles when
operating the machine.
c. Never wear jewelry or loose-fitting clothing that
might become entangled in moving or rotating
parts of the machine.
3. Make sure the splitter is on a level surface. Block
tires and ensure support leg is secure to prevent
unintended movement of the log splitter during
operation.
a. Always operate the splitter from the
manufacturer’s indicated operator zone.
4. Logs to be split on ram-type units should be cut as
squarely as possible.
5. Fuel:
a. Use an approved fuel container.
b. Never add fuel to a running or hot engine.
c. Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
d. Replace gasoline cap securely and clean up any
spilled fuel.

6
92251-1 ENGLISH
SAFETY RULES
Maintenance and Storage
1. Always shut off the power source while repairing or
adjusting the splitter except as recommended by the
manufacturer.
2. Clean debris and chaff from the engine cylinder,
cylinder head fins, blower house rotation screen,
and muffler areas. If the engine is equipped with a
spark arrestor muffler, clean and inspect it regularly
(follow manufacturer’s service instructions).
Replace, if damaged.
3. Never store the unit indoors with fuel in the tank.
Fumes might reach an open flame spark. Allow the
engine to cool before storing in any enclosure.
4. Clear debris from moveable parts, but only when the
power source is shut off.
5. Check to be sure all nuts and bolts are tight to
assure the equipment is in safe working condition.
Operation
1. Before starting this log splitter, review all safety
rules. Failure to follow these rules may result in
serious injury to the operator or bystanders.
2. Be sure to confirm all hose connections and hose
clamps are tight before each use. It is possible for
connections to vibrate loose over time.
3. Never leave the machine unattended with the power
source operating.
4. Never operate the machine when under the
influence of alcohol, drugs or medication.
5. The machine owner should instruct all operators in
safe log splitter operation.
6. Always operate the log splitter with all safety
equipment in place and all controls properly
adjusted for safe operation.
7. Always operate the log splitter at manufacturer’s
recommended speed.
8. Always keep hands and feet clear of moving parts.
9. When loading a ram-type log splitter, place your
hands on the sides of the log, not the ends. Never
place your hands or any part of your body between a
log and any part of the log splitter.
a. On ram-type log splitters, never attempt to split
more than one (1) log at a time unless the ram
has been fully extended and a second log is
needed to complete the separation of the first
log.
10. On ram-type log splitters on which the logs are not
cut square, the longest portion of the log should
be rotated down and the most square end placed
against the ram.
11. Use only your hand to operate the log splitter
controls.
12. Do not refuel the engine until it has cooled for several
minutes.

7
ENGLISH 92251-1
(1) 2 in. (5.1 cm) Ball Coupler – For towing the log
splitter behind your vehicle.
(2) Hydraulic Cylinder – 3.9 in. (10 cm) bore x
22.6 in. (57.5 cm) stroke. Rated to 3600 psi.
(3) Mounting Plates – Holds hydraulic cylinder in
place.
(4) Control Valve Handle – Controls the movement of
the cutting wedge.
(5) Wedge
(6) Splitting Beam
(7) Engine – 208cc, OHV, 4-stroke, air cooled.
(8) Tires – Maximum travel speed is 45 MPH (72 KPH).
(9) Hydraulic Pump – Pumps hydraulic oil through the
system.
(10) Hydraulic Fluid Filter
(11) Beam Bracket – Holds splitting beam in place.
(12) Support Leg – Supports log splitter while
operating. Raise leg for towing.
(13) Safety Chains – For use while towing.
Log Splitter
CONTROLS AND FEATURES
Read this owner’s manual before operating your log splitter. Familiarize yourself with the location and function of the
controls and features. Save this manual for future reference.
1
2
5
10
6
7
12
8
13
4
3
9
11

8
92251-1 ENGLISH
ASSEMBLY
A
A
Your log splitter is requires some assembly.
If you have any questions regarding the assembly of your
log splitter, call our help line at 1-877-338-0999. Please
have your serial number and model number available.
Open Shipping Crate
1. Set the shipping crate on a solid, flat surface
2. Carefully cut the shipping bands and remove lid of
shipping crate.
3. Locate all hardware before beginning assembly.
1) Install the Tow Bar
1. Assemble two piece tow bar with two M12x65 bolts
and M12 lock nuts and washers. (A)
2. Attach the tow bar to the bracket on top of the hydraulic
oil tank with two M12x85 bolts and M12 lock nuts. (B)
2) Install the Wheels
1. Place bearings in the wheel hub
2. Press the seal over the bearing on the inside of the
wheel. Use a hammer and wood block to flush the seal
with the end of the hub.
3. Slide the wheel over the axel on the hydraulic oil tank.
4. Install the castle nut and tighten by hand. Tighten
another ¼ turn with a wrench to seat the bearing.
5. Spin the wheel to distribute grease.
6. Loosen the castle nut and re-tighten by hand.
7. Install the cotter pin through the castle nut and axle to
prevent the nut from backing off.
8. Place axle cap over castle nut and axle.
9. Repeat steps 1-8 for the other wheel.
3) Install the Beam
1. Install the front support leg and secure with pin and
R-pin (hairpin clip). (A)
2. Stand the beam upright on foot plate behind the
hydraulic fluid tank. (B)
Keep the wheel hub clean and free from debris
during assembly.
NOTE
B
B
2) Install the Wheels Cont’d.
Beam is heavy. Use at least 2 people when lifting or
moving the beam.
CAUTION
Over-tightening the castle nut will cause the
bearings to run hot and fail prematurely.
CAUTION

9
ENGLISH 92251-1
ASSEMBLY
C
D
A
3) Install the Beam Cont’d. 4) Install the Cylinder and Wedge Cont’d.
4) Install the Cylinder and Wedge
1. Place the wedge on the beam between the cylinder
mounts and slide it forward into the rails. (A)
2. Remove the cylinder mounting plates. (A)
5) Install the Oil Filter
1. Remove the oil filter from the oil filter base.
2. Install the oil filter base onto the hydraulic oil tank.
The barb fitting should be oriented vertically and
once installed the oil filter should be oriented so that
it does not extend below the hydraulic oil tank.
3. Lightly lubricate the filter seal with oil.
4. Install the oil filter onto the oil filter base. Tighten ¾-1
turn once the oil filter seal contacts the oil filter base.
5. Install the hose retaining ring to the side of the
splitting beam.
3. Install the cylinder by sliding the pegs at the end
of the cylinder into the mounting slots on top of the
beam. Be sure to slide the cylinder all the way back
into the mounting slots. (B)
5. Hold the top of the beam by the cylinder mount and
carefully rotate the beam toward the tow bar.
6. Once the bracket on the bottom of the beam is aligned
with the tow bar, secure with pin and R-pin. (D)
The cylinder will support itself when slid all the way
back into the mounting slots.
NOTE
4. Secure the cylinder mounting plates with hardware
removed in step 2. (B)
5. Slide the wedge back toward the cylinder and align
the bolt hole in the wedge with the bolt hole in the
cylinder rod. (B)
6. Secure the wedge to the cylinder rod with an
M12x75 bolt and M12 nut. Lightly tighten the nut to
approximately 5 ft-lb. (B)
B
The cylinder rod may need to be rotated slightly
in order to properly align the the wedge. Insert a
screwdriver into the bolt hole in the cylinder rod
and slowly rotate as needed.
NOTE
3. Slowly lift the front of the tow bar to roll the frame
toward the beam and carefully align the pivot holes
on the bottom of the beam and the top of the
hydraulic oil tank.
4. Once aligned, secure the beam to the tank with hitch
pin and R-pin. (C)

10
92251-1 ENGLISH
ASSEMBLY
6) Install the Engine and Hoses Cont’d.
6) Install the Engine and Hoses
1. Attach the engine/pump to the engine mounting plate
on the hydraulic oil tank. (A)
2. Place O-ring into the outlet fitting on the top of the
pump. (A)
3. Connect one end of the high pressure hose to the
pump outlet fitting and the other end to the inlet on
the control valve. (B)
4. Connect one end of the clear oil hose to the hydraulic
oil tank just beneath the engine and the other end to
the pump inlet on the bottom of the pump. (C)
The swivel nut end of the high pressure hose
connects to the pump outlet.
NOTE
5. Connect one end of the oil return hose to the outlet
barb fitting on the control valve and the other end to
the barb fitting on the oil filter. (D)
C
B
A
D
Add Hydraulic Oil
1. Make sure the log splitter is on a flat, level surface.
2. Remove the oil plug from the oil tank. (A)
3. Add 4 gallons (15.1 L) of hydraulic oil - 10W AW32,
ASLE H-150, or ISO 32 are all acceptable types of
fluid.
4. Check the hydraulic oil level using the oil sight glass.
Oil level should visibly fill the glass sight. (B)
5. Replace and tighten the oil plug and orient the vent
DO NOT remove the hydraulic oil fill cap when the engine
is running or hot. Hot oil can escape causing severe
burns. Always allow the log splitter to cool completely
before removing the hydraulic oil cap.
High fluid pressure and temperatures are created in the
hydraulic log splitters. Hydraulic fluid will escape through
a pin-size hole opening and can puncture skin and cause
severe blood poisoning.
Inspect hydraulic system regularly for possible leaks.
Never check for leaks with your hand while the system
is pressurized. Seek medical attention immediately if
injured by escaping fluid.
WARNING
A
B
When temperature is below 0ºC (32ºF) use
universal tractor/transmission fluid.
NOTE

11
ENGLISH 92251-1
ASSEMBLY
The engine is equipped with a low oil shut-off and
the will stop when the oil level in the crankcase
falls below the threshold level.
CAUTION
Add Engine Oil
1. Make sure the log splitter is on a flat, level surface.
2. Remove oil fill cap/dipstick to add oil.
3. Add up to 0.6 qt. (0.6 L) of oil and replace oil fill
cap/dipstick. DO NOT OVERFILL.
4. Check engine oil level daily and add as needed.
DO NOT attempt to crank or start the engine before
it has been properly filled with the recommended
type and amount of oil. Damage to the log splitter
as a result of failure to follow these instructions will
void your warranty.
CAUTION
Check oil often during the break-in period. Refer to
the Maintenance section for recommended service
intervals.
NOTE
Add Hyrdraulic Oil Cont’d.
hole away from the operator zone.
6. Start Engine. Extend and retract the wedge to purge
air from the hydraulic system. When the wedge
motion is smooth, the system is properly purged.
7. Check the hydraulic oil tank sight glass. Add
approximately 1 to 1.5 gallons (3.8 to 5.7 L) of
hydraulic oil to bring the level back up to the sight
glass.
8. Check oil level daily and add as needed.
Add Engine Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol
content of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL.
Fuel can expand after filling. A minimum of ¼ in.
(6.4 mm) of space left in the tank is required
for fuel expansion, more than ¼ in. (6.4 mm) is
recommended. Fuel can be forced out of the tank
as a result of expansion if it is overfilled, and can
affect the stable running condition of the product.
When filling the tank, it is recommended to leave
enough space for the fuel to expand.
6. Screw on the fuel cap and wipe away any spilled fuel.
Use regular unleaded gasoline with a minimum octane
rating of 85.
Do not mix oil and gasoline.
Fill tank to approximately ¼ in. (6.4 mm) below the top
of the tank to allow for fuel expansion.
DO NOT pump gas directly into the engine at the gas
station. Use an approved container to transfer the fuel to
the engine.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the fuel tank.
CAUTION
Pouring fuel too fast through the fuel screen may
result in blow back of fuel at the operator while filling.
WARNING
Our engines work well with 10% or less ethanol blend
fuels. When using blended fuels there are some issues
worth noting:
– Ethanol-gasoline blends can absorb more water than
gasoline alone.
– These blends can eventually separate, leaving water
or a watery goo in the tank, fuel valve and carburetor.
– With gravity-fed fuel supplies, this compromised fuel
can be drawn into the carburetor and cause damage
to the engine and/or potential hazards.
– There are only a few suppliers of fuel stabilizer that
are formulated to work with ethanol blend fuels.
– Any damages or hazards caused by using improper
fuel, improperly stored fuel, and/or improperly
formulated stabilizers, are not covered by
manufacture’s warranty.
It is advisable to always shut off the fuel supply, run the
engine to fuel starvation and drain the tank when the
equipment is not in use for more than 30 days.
NOTE

12
92251-1 ENGLISH
OPERATION
Before Each Use Inspect the Log Splitter
1. Check the hydraulic oil level and visually inspect all
hoses, attachments and cylinder for loose fittings,
leaks, cracks, fraying or other damage.
2. DO NOT operate the log splitter if there is any
indication of damage.
3. Inspect the engine and make sure the oil level is
correct before operating. If the engine is equipped
with a spark arrestor, clean and inspect it regularly
(follow spark arrestor maintenance schedule).
4. The tires need to be fully inflated and in good repair.
Reference the tire sidewall for recommended tire
pressure.
Towing Log Splitter Safety
1. Always check local and state regulations regarding the
requirements for towing, licensing and lights.
2. Before towing make sure the log splitter is correctly
and securely attached to the vehicle and the safety
chains attached with enough slack to allow for turning.
3. Never exceed the max. travel speed of 45 mph
(72 kph). Towing the log splitter at speeds greater
than 45 mph (72 kph) could result in serious injury or
death. Always adjust your towing speed according to the
terrain and conditions.
4. Always disconnect the log splitter from the towing
vehicle before operating.
Log Splitter Location
This log splitter must have at least seven feet of
clearance from combustible material. Leave at least
three feet of clearance on all sides of the log splitter to
allow for adequate cooling, maintenance and servicing.
DO NOT place the log splitter near vents or intakes
where engine exhaust fumes could be drawn into
occupied or confined spaces. Always operate the log
splitter outdoors.
The log splitter needs to be on a dry level surface with
good footing. DO NOT work on mud, ice, tall grass,
brush or snow.
Only operate log splitter from work zone shown below.
DO NOT over inflate tires. Serious injury can result
if tires explode.
DO NOT tow the log splitter if the tires are worn or
will not hold air.
DO NOT exceed the maximum 45 MPH (72 KPH)
towing speed.
WARNING
Vertical Operating
Position
W
o
r
k
Z
o
n
e
Horizontal Operating
Position
W
o
r
k
Z
o
n
e
Log Splitter Location Cont’d.

13
ENGLISH 92251-1
OPERATION
ALWAYS use the log splitter for its intended use. The
log splitter should only be used to split wood logs,
length wise with the grain.
NEVER modify, alter or change the log splitter in
anyway. Modifications will void the warranty.
NEVER attach a rope, cable or other device to the
control lever on the log splitter.
DO NOT modify or change the engine and operating
speeds or pressure settings. These changes can
cause safety issues.
ONLY operate the log splitter in daylight.
NEVER operate, or let anyone else operate, the log
splitter while under the influence of alcohol, drugs,
or medication.
NEVER leave the log splitter unattended while the
engine is running.
DO NOT change the splitting position with the engine
running. Contact with the muffler can cause serious
burns.
Always make sure the beam is in the locked position.
DO NOT let the beam drop as it could crush fingers
or cause damage to the log splitter.
WARNING
Log Splitter Location Cont’d. Starting the Engine Cont’d.
Starting the Engine
1. Make certain the log splitter is on a flat, level surface.
2. Turn engine switch to “ON” position.
3. Turn the fuel valve to the “ON” position.
4. Move the choke lever to the “Choke” position.
5. Pull the starter cord slowly until resistance is felt and
then pull rapidly. SEE NOTE BELOW.
6. As engine warms up, move the choke lever to “Run.”
7. Move the throttle lever to the “Fast” position.
Starting the Engine Cont’d.
If the engine starts, but does not run, make certain
that the log splitter is on a flat, level surface. The
engine is equipped with a low oil sensor that will
prevent the engine from running when the oil level
falls below a critical threshold.
The hydraulic oil needs to be above -12°C (10°F)
before starting the engine. Cold hydraulic oil can
damage the hydraulic pump.
If outdoor air temperature is below 0°C (32°F)
allow the log splitter to warm up by extending and
returning the wedge several times before splitting
wood.
NOTE
Keep choke lever in “Choke” position for only 1
pull of the recoil starter. After first pull, move choke
lever to the “Run” position for up to the next 3
pulls of the recoil starter. Too much choke leads to
spark plug fouling/engine flooding due to the lack of
incoming air. This will cause the engine not to start.
NOTE
Stopping the Engine
1. Turn the fuel knob to the “Off” position.
2. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
3. Turn the engine switch to the “Off” position.
Important: Always ensure that the Fuel Valve and the
Engine Switch are in the “OFF” position when the engine
is not in use.
If the engine will not be used for a period of two (2)
weeks or longer, please see the Storage section for
proper engine and fuel storage.
NOTE

14
92251-1 ENGLISH
OPERATION
HORIZONAL position is used for lighter logs that can
easily be loaded onto the beam.
VERTICAL position is used for light logs as well as
heavy logs that are difficult to load onto the beam.
Back injury can result from lifting logs onto the log
splitter if proper lifting techniques are not used.
NOTE
It is normal for the hydraulic fluid to become foamy
or frothy during operation.
NOTE
Log Splitter Operation
1. ALWAYS wear ear and eye protection, protective clothing
and safety gear.
2. Block tires and put both support legs in the DOWN
position to prevent unintended movement of the log
splitter during operation.
3. Set log splitter in either the horizontal or vertical
position.
4. Load a log onto the beam against the end plate (MAX
LOG LENGTH – 23.8 in. (60.3 cm)
5. Make sure all limbs are clear of crush zones.
6. Push the control valve handle forward (towards the
end plate) to split the log.
7. Push the auto control valve handle backward to
return the wedge to its original position.
8. Clear the split wood from the work zone.
Do not hold auto control valve in return position. It
will damage the stop block or beam.
CAUTION

15
ENGLISH 92251-1
MAINTENANCE AND STORAGE
The owner/operator is responsible for all periodic
maintenance.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the log splitter.
Improper maintenance will void your warranty.
For service or parts assistance, contact our help line
at 1-877-338-0999.
NOTE
Never operate a damaged or defective log splitter.
WARNING
WARNING
Oil Cont’d.
Air Filter
1. Using your fingers, press and slide the top of the air
filter housing to remove.
2. Remove the plastic outer casing.
3. Remove the foam element.
4. Wash in liquid detergent and water. Squeeze
thoroughly dry in a clean cloth.
5. Saturate in clean engine oil.
6. Squeeze in a clean, absorbent cloth to remove all
excess oil.
7. Place the filter in the assembly.
8. Reattach the air filter cover.
Used oil is a hazardous waste product and must be
disposed of properly. Do not discard with household
waste. Check with your local authorities, service
center, or dealer for safe disposal/recycling facilities.
WARNING
Engine Maintenance
To prevent accidental starting, remove and ground spark
plug wire before performing any service.
Oil
Change oil when the engine is warm. Refer to the oil
specification to select the proper grade of oil for your
operating environment.
1. Remove the oil drain plug with a 10 mm socket and
extension.
2. Allow the oil to drain completely.
3. Replace the drain plug.
4. Remove oil fill cap/dipstick to add oil.
5. Add 0.6 qt. (0.6 L) of oil and replace oil fill cap/
dipstick. DO NOT OVERFILL.
6. Dispose of used oil at an approved waste
management facility.
Spark Plugs
1. Remove the spark plug cable from the spark plug.
2. Inspect the electrode on the plug. It must be clean
and not worn to produce the spark required for
ignition.
3. Make certain the spark plug gap is 0.6 - 0.8 mm
(0.024 - 0.031 in.).
4. Refer to the spark plug recommendation chart when
replacing the plug.
5. Carefully thread the plug into the engine.
6. Use the spark plug tool to firmly install the plug.
7. Attach the spark plug wire to the plug.
0.6 - 0.8 mm
(0.024 - 0.031 in.)
Once oil has been added, use the dipstick to check oil
level, DO NOT screw in the dipstick while checking.
NOTE
FILL
FILL
DIPSTICK

16
92251-1 ENGLISH
MAINTENANCE AND STORAGE
Always shut off the engine, disconnect the spark
plug, and relieve system pressure before cleaning,
adjusting, or repairing the splitter. Relieve system
pressure by moving split control lever back and
forth several times
WARNING
1. Begin with the cylinder retracted and the engine
“ O F F.”
2. Turn the fuel valve “OFF.”
3. Release any stored pressure by moving the valve
lever forward and backward several times.
4. Place a container under the hydraulic tank. Make
sure it is large enough to hold the contents of the
tank.
5. To drain the oil, unscrew and remove the tank drain
plug on the bottom of the hydraulic tank.
a. Unscrew and remove the hydraulic oil filter.
b. Drain any oil in the filter into the container.
6. Allow oil to completely drain from the tank into the
container.
7. Install a new hydraulic oil filter. (A)
a. Turn the filter counter-clockwise to remove it. A
strap wrench may be used.
b. Lubricate the gasket of the new filter with a thin
film of clean oil.
c. Screw the new filter on clockwise. Tighten
¾ to 1 turn after the gasket makes contact.
8. Reinsert and screw in the tank drain plug. Tighten,
but do not over tighten.
B
AC
Change the hydraulic oil filter after the first 50 hours
of use. Then every 100 hours or seasonally.
NOTE
Install a new hydraulic oil filter each time the
hydraulic oil is changed
NOTE
The drain plug is sealed with Teflon tape. Add 2-3
wraps of new Teflon tape as needed when replacing
the drain plug to prevent oil leak
NOTE
Refer to Specifications for a list of compatible
replacement filters or call Champion Power
Equipment at 1-877-338-0999 to order a
replacement OEM filter.
NOTE
Changing the Hydraulic Oil and Oil Filter Cont’d.Changing the Hydraulic Oil and Oil Filter
9. Unscrew and remove the tank fill plug, on top of the
tank. Using a funnel add approximately 4 gallons
(15.1 L) of hydraulic oil to the tank. Wipe up any
spilled oil. (B)
10. Turn the fuel valve on, and start the engine. Purge
the air from the system by extending and retracting
the wedge several times until the motion is smooth.
11. Check the hydraulic oil level using the sight glass.
Add 1 to 1.5 gallons (3.8 to 5.7 L) of hydraulic oil,
so the oil level is visible in the sight glass. (C)
12. Dispose of used oil at approved recycling locations.

17
ENGLISH 92251-1
MAINTENANCE AND STORAGE
DO NOT use a garden hose to clean the engine or
log splitter.
CAUTION
Water can contaminate the fuel system and can enter the
engine through the cooling slots and damage the engine.
Maintenance Schedule
Follow the service intervals indicated in the schedule
below. Service your log splitter more frequently when
operating in adverse conditions. Contact our help line at
1-877-338-0999 to locate the nearest Champion Power
Equipment authorized service dealer for your log splitter
or engine maintenance needs.
Log Splitter Maintenance
Make certain that the log splitter is kept clean and stored
properly. Only operate the unit on a flat, level surface in
a clean, dry operating environment. DO NOT expose the
unit to extreme conditions, excessive dust, dirt, moisture
or corrosive vapours.
Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
Clean spark arrester every 100 hours.
Check and tighten all bolts and nuts before operating the
log splitter.
Storage
Refer to the Maintenance section for proper cleaning
instructions.
Log Splitter Storage
1. The log splitter needs to be cool for at least 5
minutes before storing.
2. Clean the log splitter before storage according to the
Maintenance section.
3. Retract the wedge to protect the rod from corrosion.
4. Wipe the beam and wedge with an oily rag to
prevent rust and corrosion.
Engine stored for Less than 30 Days
1. Allow the engine to cool completely before storage.
2. Clean engine according to the Maintenance section.
3. To extend the fuel storage life add fuel stabilizer.
4. Turn the fuel valve to the “Off” position.
Engines Stored for Over 30 Days
1. Run the engine with the fuel valve in the “Off”
position until the engine stops.
2. The engine needs to cool completely before storage.
3. Clean engine according to the Maintenance section.
4. Drain all fuel completely from the fuel line and
carburetor to prevent gum from forming.
5. Add a fuel stabilizer into the fuel tank.
6. Change the oil.
7. The fuel valve needs to be in the off position.
8. Remove the spark plug and pour about 14.8 mL
(1/2 oz.) of oil into the cylinder. Crank the engine
slowly to distribute the oil and lubricate the cylinder.
9. Reattach the spark plug.
*To be performed by knowledgeable, experienced owners or
Champion Power Equipment certified dealers.
Cleaning
Clear the debris from the beam, wedge and endplate. Use
a damp cloth to clean exterior surfaces of the engine and
log splitter.
Use a soft bristle brush to remove excess dirt and oil. Use
an air compressor (25 PSI) to clear dirt and small debris.
Wipe all metal parts with an oily rag to help prevent rust
and corrosion.
Every time of use or daily
Check engine and hydraulic oil levels
Clean around air intake and muffler
Check air filter
First 5 Hours
Change engine oil
Every 25 Hours or per 1 month
Change engine oil
Clean air filter
Every 50 hours or per 6 months
Clean and adjust spark plug
Check cooling fan
Every 100 hours or per 1 year
Check/adjust maximum load speed*
Check/adjust valve clearance*
Clean fuel tank and filter*
Change hydraulic oil
Change hydraulic oil filter
Every year
Inspect wheel bearings and repack bearing grease
as needed.
Every 200 hours
Clean combustion chamber
Every 200 hours or per 2 years
Check/replace fuel line
Change spark plug