Page 4 of 4 75.5172.08 PANTHER SERIES 20230420
FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI
MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900
MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900
MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900
FCC ID: 2ABWS-10TD433PTRII IC: 4680-10TD433PTRII
MODEL: 10EMR61 MODEL: 10EMR4751 MODEL: 10EMS4751
MODEL: 10EMR6 MODEL: 10EMR475 MODEL: 10EMS475
MODEL: 10EMR6L MODEL: 10EMR475L MODEL: 10EMS475L
Page 4 of 4 75.5172.08 PANTHER SERIES 20230420
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device;
therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/
gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring
that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s
recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must
be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.
ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
TECHNICAL SPECIFICATIONS
Dimensions 6” ROUND - 6.33” diameter, 1.45” depth
4.75” ROUND - 5.12” diameter, 1.42” depth
4.75” SQUARE - 5.12” height, 5.12” width, 1.42” depth
Weight 6” ROUND - 1.2 lbs
4.75” ROUND - 1.14 lbs
4.75” SQUARE - 1.04 lbs
Material FACEPLATE - stainless steel
HOUSING - ABS plastic
Transmitter Frequency 433 MHz or 900 MHz
Power 900 MHz versions - two (2) CR2032
433 MHz versions - one (1) 12V Type A23
Mounting Surface mount only
Certification FCC, IC
Temperature 14 °F - 131 °F (-10 °C - 55 °C)
Enclosure Rating NEMA 4
Specifications are subject to change without prior notice.
All values measured in specific conditions.
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING
©BEA|OriginalInstructions|75.5172.08PANTHERSERIES20230420
Tech Support & Customer Service: 1-800-523-2462
FCC / IC
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.”
Changes or modifications not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
