Beam iridium SatDOCK 9555with built in GPS User manual

QUICK START GUIDE
iridium SatDOCK 9555
with built in GPS
Suitable for the Iridium 9555
Portable Satellite Telephone
Beam Communications Pty Ltd
8. Using SatDOCK 9555
• AfterapplyingpowertoACpoweradaptororturningkey/Accon,the
SatDOCKwillbeepuponpowerup
• Waitforphonetopowerupandregister
PANEL BUTTONS AND INDICATORS:
6. Options
Tracking & Alert:
Tracking&AlertrequiresGPSantenna,andsetupofthetrackingand/or
alerting messages. Please refer to the SDMS Application (SatDOCK
ManagementSystem)toenableandcongureTracking&Alert.
External Alert Button:
Connect Normally-CLOSED button, to the Brown
andGreenwires(itcanbeextendedforlongerruns).
TheloopneedstobeOPEN(eg.pressingbutton)for
2secondstoactivateAlertstate.
Privacy Handset:
1. ThePrivacyHandsetKitisorderedseparately.
2. Mountthehandsetcuptothemountingplate.
3. Mount the spacer plate and the mounting
bracket, by using the longer screws provided
withthekit.(Re-installedtheRAMarm-bracket
behindtheseplates).
4. ConnectthePrivacyHandset3.5mmpluginto
therearcablejack.
5. PrivacyHandsetmodeisactive wheneverthe
handsetisremovedfromthecup.
Intelligent Handset:
1. Mountthehandsetcupinasuitableposition
2. ConnecttheIntelligenthandsetRJ45connector
intotherearcablejack.
3. Intelligenthandsetmodeisactivewheneverthe
handsetisremovedfromthecup
Earpiece-Jack Mode:
Usea2.5mmearpiecepluggedintotherightsideofthe9555handset.
1. DuringaRJ11orBluetoothcall,toenableEarpiece-JackMode,press
andholdtheMutebuttonfor1.5seconds.TheLEDashesORANGE.
2. ToexitEarpiece-JackModeandreverttoRJ11orBluetooth,press
theMutebuttononce.
www.beamcommunications.com
[email protected]
TEL: [phone] FAX: [phone]
USRQSG005501
7. Add Bluetooth Device (optional)
AUDIO:Tocongure(pair)toaBluetooth®headsetdevice:
1. DiscoveryMode:Press and hold for 5 secstheBluetooth®buttonon
thecradle.TheLEDashesBLUEandORANGE.
2. HoldtheHeadsetdevicebutton(s)toenterpairingmode.
3. Oncepaired,theBluetooth®LEDisBLUE(halfintensity).
4. Bluetooth®canbeturnedONwithasingle press,andOFFbypress for
2 secstheBluetooth®buttononthecradle.
BUTTON BUTTON MODE LED/SOUND
Out of Call (single press):
Select Ringer Tones
LED off.
Preview and select ringer sounds.
Out of Call (1.5 second press)
Auto-Answer Mode:
Subsquent 1.5 second press
exits auto-answer
LED is GREEN, single beep.
During In-Call Hands-free,
Privacy/Intelligent handset
or Bluetooth®:
Mute (single press)
LED is RED when MUTE.
During In-Call Bluetooth®:
Earpiece-jack
(1.5 seconds press)
Subsequent single press, exits
Earpiece-jack
LED ashes ORANGE.
Bluetooth® On
(single press)
Bluetooth® OFF
(1.5 seconds press)
LED is BLUE (half intensity) when
Bluetooth® ON and is connected
LED is fast-ashing in BLUE when
searching paired device.
LED is slow-ashing BLUE when a
connected Bluetooth® device is in use.
Single beep sounds when Bluetooth®
turning OFF.
Discovery Mode
(5 seconds press)
LED ashes ORANGE and BLUE.
Ringer sounds double (2) beeps.
Clear Bluetooth® Devices
(10 seconds press)
Ringer sounds triple (3) beeps.
Send Tracking Message
(single press)
LED and beep operates according to
the settings in PDMS.
Clear Alert Mode
(7 seconds press)
LED turns GREEN re-armed & GPS x
ready. Single Beep sounds.
If LED is ashing in GREEN – No GPS
x, or no Iridium signal
LED is OFF when Track & Alert is
disabled.
+
Activate Alert Mode
(2 seconds press, BOTH
buttons together)
Track LED turns RED when alert is
triggered and single beep sounds.
Track LED is ashing in RED when the
alert message is sent.
Track LED is ashing in ORANGE
when the alert message is
acknowledged by a remote host.

2. Installing SatDOCK Cradle
2.Afxotherbaseto
SatDOCKwithM4
screws
1.Removebase
platesby
looseningwingnut
Considerations:
• Afxthebaseplateinalocationthatallowseasyaccess&doesnot
obstructdriver
• AllowsufcientroomtoeasilyruncablesfromtheSatDOCK
• ONLYusetheM4screws(supplied)toafxthebasetothe
SatDOCKtoavoidanydamage
• ForwallmountingusetheRAMBracketwithbothbasesparallel
toeachother
• TightenwingnutonthebrackettosecurelyholdtheSatDOCK
• Avoidmakinganysharpbendsintheantennacablewhen
determiningthecableroute
• ThexedcablesfromtheSatDOCKshouldneverbeextended,
Antennacablesmustbeapproved
3. Installation
• DONOTroutecablesnearareasofintenseheat
• DONOTpullorstrainthecablesfromtheSatDOCK
Connecting to Power:
• ConnectACpowerAdaptor,orDCCableLead(9-32VDCinput>25watts)
Connecting to the Antennas:
• OnlycertiedcableswithintheIridiumspecicationshouldbeused
• Ensureantennacablesareroutedavoidinganysharpbendsinthecable
• Theantennashouldalwaysbeinstalledwithclearlineofsitetothesky
SatDOCK USB Data Port:
• TheSatDOCKhasanintegratedUSBDataPortontherear.Drivers
forthisUSBportcanbedownloadfrom
http://www.beamcommunications.com/support/satdock9555
3.Rejointhetwo
basesusingthearm
WARNING: Your Iridium 9555 Handset requires rmware
HT10001 or greater.To check your rmware version on your
Iridium9555handsetpress“Menu”thennavigateto“Setup”then
“PhoneInformation”. For moreinformation and9555 Handset
rmwaredownloadsvisit:
http://www.beamcommunications.com/support/satdock9555
NOTE: For Data operation the USB port on the Iridium 9555
handsetmust not be used whilst dockedin the cradle. Please
usetheUSBportlocatedonthebottomofthe9555cradle.
5. Inserting & Ejecting 9555
Handset
Inserting:
1. Remove rubber grommet on
backof9555antennaconnection
2. Ensure9555handsetisturnedoff
3. Ensurethereisnoforeignobject
inthecradle
4. Placethe9555inthecradlewith
thebaseinrst
5. The base connector should line
upwiththebaseofthe9555
6. Press EJECT button and phone
atthesametimetosecurelylock
thephoneinthedockingstation.
Ejecting:
To remove the 9555 handset from
thecradleFIRMLYpressthe“Eject”
button located on the top of the 
cradle(seediagram).
2.PushEJECT
andphoneat
thesametime
1.Place9555on
thebaseofthe
cradle&pushinto
thecradle
1.Firmlypress
‘Eject’Button
2.Releasethe
phone
Speaker
MIC
Speaker
MIC
Installing Speaker:
• Mount the speaker underneath the seat or other location that
avoids the speaker facing the microphone
• If feedback occurs upon testing try redirecting the speaker or
locate in another location.
4. MIC / Audio Connections
Connecting Microphone:
• The microphone should be connected to the HFI and then recessed
up the door pillar or similar to a head height location close to the driver
• Care should be taken to avoid wind or high noise environments
• Avoid crimping or damaging the microphone cable during installation
Privacy
Handset
9555 Handset
Antenna Plug
EJECT Button
Mini USB
Data Port
Intelligent
Handset
1
cok
4
789
0

*#
56
23
GME
SPK07
Iridium Antenna (TNC Female)
GPS Antenna (SMA Female)
Horn Alert
Alert Loop (IN / OUT)
Speaker
Microphone
1. SatDOCK Installation Set Up
Bluetooth Device
(Optional)
INSTALL POWER:
BLACK = 0V Ground to negative Battery.
RED + VIN wire to the vehicle + Battery (3A fuse).
YELLOW Acc (On/Off sense) to behicle acc/key, or on/off switch (1A fuse).
If not required, this YELLOW wire MUST be connected to +VIN (RED WIRE)
Track Bluetooth
ALERT
BEAM
Mute
Ringer
iridium SatDOCK