Becker PSF+ Series User manual

P5/20C...L120/11C
Version: PSF+
en Assembly and Operating Instructions
Sun protection drives with integrated radio receiver
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com

Table of contents
General ............................................................................................................................................................................... 3
Warranty ............................................................................................................................................................................. 3
Safety instructions ............................................................................................................................................................... 4
Instructions for the user................................................................................................................................................... 4
Instructions for installation and commissioning.................................................................................................................. 4
Intended use ....................................................................................................................................................................... 5
Assembling and disassembling the plug-in connecting cable................................................................................................... 6
Assembling the plug-in connecting cable .......................................................................................................................... 6
Disassembling the plug-in connecting cable for tubular drives dia. 35. ................................................................................ 6
Disassembling the plug-in connecting cable for tubular drives dia. 45 and dia. 58 ................................................................ 7
Installation........................................................................................................................................................................... 8
Assembling the drive ....................................................................................................................................................... 8
Undoing the mounting pin................................................................................................................................................ 8
Assembling the drive adapter with drive adapter safety catch.............................................................................................. 8
Assembling the drive adapter with screw connection.......................................................................................................... 9
Securing the drive against axial displacement.................................................................................................................... 9
Fixing the drive adapter to the barrel dia. 35 and dia. 45 and dia. 58 .................................................................................... 9
Mounting the drive in the tube ........................................................................................................................................ 10
Confirming the drive ...................................................................................................................................................... 10
First operation ................................................................................................................................................................... 11
Intelligent installation management ................................................................................................................................ 12
Programming the master transmitter .............................................................................................................................. 12
Checking that the running direction is correct.................................................................................................................. 12
Setting the limit positions............................................................................................................................................... 13
Extended position to retracted position without stop ................................................................................................... 13
Extended position to retracted stop ........................................................................................................................... 14
Changing the set limit positions...................................................................................................................................... 14
Deleting the limit positions ............................................................................................................................................. 15
Intermediate positions I + II ............................................................................................................................................ 15
Programming additional transmitters.............................................................................................................................. 16
Deleting transmitters..................................................................................................................................................... 16
Overwriting the master .................................................................................................................................................. 17
Disposal............................................................................................................................................................................ 18
Maintenance ..................................................................................................................................................................... 18
Technical data dia. 35 ........................................................................................................................................................ 18
Technical data dia. 45 ........................................................................................................................................................ 19
Technical data dia. 58 ........................................................................................................................................................ 19
What to do if...?.................................................................................................................................................................. 20
Sample wiring diagram ....................................................................................................................................................... 21
Declaration of conformity ................................................................................................................................................... 22
2

General
These tubular drives are high-quality products with the following features:
•Optimised for sun protection applications
•Suitable for awnings and conservatory shades. Drives of type "+" are specially designed for cassette awnings
•Individual, group and central radio control
•No need to run wires to a switch or relay control device
•Any combination of drive and transmitter possible
•Simple to set the limit positions with the transmitter
•Installation without stops is also possible (from extended point to retracted point without stop)
•Two freely selectable intermediate positions can be set
•Flexible radio grouping; can be altered at any time with no need to install/uninstall
•Automatic detection of limit positions thanks to intelligent electronic system with stop systems
•The final positions do not have to be reset: Changes in the curtains are accommodated automatically when using stop sys-
tems.
•Considerably lower stop load, and thus considerably lower curtain load.
•Smooth operation of the system and the drive increases the service life
•For plug-in connecting cable
Please observe these Assembly and Operating Instructions when installing and setting the equipment.
The date of manufacture comes from the first four digits of the serial number.
The numbers 1 and 2 indicate the year and the numbers 3 and 4 indicate the calendar week.
Example: 24th calendar week in 2012
Ser. No.: 1224XXXXX
Explanation of pictograms
CAUTION CAUTION indicates a hazardous situation which, if not avoided, could
result in injury.
ATTENTION ATTENTION indicates measures that must be taken to avoid damage to
property.
Denotes user tips and other useful information.
Warranty
Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in
serious injuries, e.g., crushing of limbs. Therefore, structural modifications may only be carried out with our prior approval and
strictly in accordance with our instructions, particularly the information contained in these Assembly and Operating Instructions.
Any further processing of the products which does not comply with their intended use is not permitted.
The end product manufacturer and fitter have to ensure that all the relevant current statutory, official and, in particular, EMC regu-
lations are adhered to during utilisation of our products, especially with regard to end product manufacture, installation and cus-
tomer advice.
3

Safety instructions
The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury.
Instructions for the user
General information
•All work, including maintenance and cleaning, on electrical installations as well as other system parts
must always be performed by authorised specialists, in particular qualified electricians.
•Children from the age of 8 years and persons with reduced physical, sensory or mental capabilities or
lack of experience and/or knowledge may use these devices, provided they are supervised or have
been instructed in the safe use of the device, and have understood the hazards involved. Children must
not play with the device.
•Systems have to be checked regularly by authorised specialists for wear and damage.
•Always put damaged systems out of operation immediately until they are repaired by an authorised
specialist.
•Do not operate equipment if people or objects are within the danger zone.
•Observe the danger zone of the equipment during operation.
•Stop and disconnect the equipment from the mains power supply when maintenance and cleaning is
being performed either on the system itself or in the immediate vicinity of it.
•Ensure that there is adequate clearance (at least 40cm) between moving parts and adjacent objects.
Caution
Safety instructions for avoiding serious injuries.
•Crushing or shearing points must be avoided or protected.
Instructions for installation and commissioning
General information
•Observe the safety instructions in EN 60335-2-97. Please note that this list of safety instructions is not
exhaustive, since it would be impossible for the standard to include all sources of danger. For example,
the design of the operated product, the way the drive works in the situation it is installed in or even the
way the end product is mounted in the end user’s place of use cannot be taken into consideration by
the drive manufacturer.
If any questions or uncertainties regarding the safety instructions contained in the standard arise,
please contact the manufacturer of the part or end product in question.
•All applicable standards and regulations for electrical installation must be complied with.
•All work, including maintenance and cleaning, on electrical installations as well as other system parts
must always be performed by authorised specialists, in particular qualified electricians.
•Only use spare parts, tools and accessory devices which have been approved by the drive manufac-
turer.
Unapproved third-party products or modifications to the system and its accessories represent a risk to
your safety and the safety of others. This means that the use of unapproved third-party products, or
modifications which have not been agreed with or approved by us, are prohibited. We do not accept li-
ability for damage or injury arising from such actions.
•Position control devices within sight of the driven product, but away from moving parts, at a height of
over 1.5m.
•Permanently mounted control devices must be positioned where they can be seen.
•Rated torque and duty cycle must be suitable for the requirements of the driven product.
Technical data – rated torque and service life can be found on the type plate of the tubular drive.
4

•Moving parts of drives must be installed at a height of over 2.5m above floor level or any other surface
from which access to the drive is gained.
•To ensure safe operation of the system after commissioning, the limit positions must be correctly set/
programmed in.
•Drives with a H05VV-F connecting cable may only be used indoors.
•Drives with a H05RR-F, S05RN-F or 05RN-F connecting cable may be used both indoors and outdoors.
•To connect the drive to the driven part, solely mechanical accessory components made by the drive
manufacturer from the current product catalogue may be used. The components must be installed in
accordance with the manufacturer's instructions.
•If the drive is used for shading solutions in a specially marked area (e.g. escape routes, hazard zones,
safety areas), compliance with all applicable regulations and standards must be ensured.
Caution
Safety instructions for avoiding serious injuries.
•When electrical or electronic equipment and units are operated, certain components,
e.g., the power supply unit, are live. Physical injuries or damage to property can result in
the event of unauthorised interventions or failure to heed warnings.
•Be careful when touching the tubular drive, as it heats up during operation for technolo-
gical reasons.
•Before installation, shut down all lines and control devices that are not essential for op-
eration.
•Crushing or shearing points must be avoided or protected.
•When installing the drive, all-pole disconnection from the mains with a contact gap of at
least 3mm per pole must be provided (EN 60335).
•If the drive mains connecting cable is damaged, it must be replaced with the same type
of mains connecting cable, which is available from the drive manufacturer.
Attention
Safety instructions for avoiding property damage.
•Ensure that there is adequate clearance between moving parts and adjacent objects.
•The drive must not be carried by the mains connecting cable.
•All latching connections and fastening screws on the brackets must be checked to en-
sure that they are secure.
•Ensure that nothing rubs against the tubular drive, such as shading solution attach-
ments, screws, etc.
Intended use
The type of tubular drive described in these instructions is intended solely for the operation of awnings and conservatory shades. It
may only be used in networked systems if all the individual drives are exactly synchronised and reach the limit positions at the
same time.
When mounting connection parts on the drive dia. 35mm PXX/XX, only use screws EJOT Delta PT 40x12 WN 5454 Torx (9900 000
545 4).
For roller shutter applications, please use only the types of tubular drive designed for this purpose.
This type of tubular drive is designed for use in single systems (one drive per barrel).
The tubular drive must not be used in potentially explosive areas.
The connecting cable is not suitable for transporting the drive. Always carry the drive by the housing tube.
Other applications, uses and modifications are not permitted in order to protect the safety of the users and others, since these ac-
tions can impair the system’s safety and carry the risk of personal injury and property damage. The drive manufacturer does not
accept liability for damages or injury arising from such actions.
Always observe the information in these instructions when operating or repairing the system. The drive manufacturer does not ac-
cept liability for damage or injury resulting from improper usage.
5

Assembling and disassembling the plug-in connecting cable
Assembling the plug-in connecting cable
Insert the dead connecting cable into the drive head until the locating lug clicks into place in the drive. If necessary, use a suitable
flathead screwdriver to assist with insertion. Set the screwdriver into one of the two plug grooves provided for this purpose.
Check that the cable is properly engaged.
1 = locating lug
Disassembling the plug-in connecting cable for tubular drives dia. 35.
Caution
Prior to disassembly, the power supply to the connecting cable must be disconnected.
On drives with a diameter Ø35, insert a suitable flathead screwdriver between the locating lug and the snap-in pin, so that the
snap-in pin releases the locating lug from the plug.
Now you can pull out the connecting cable along with the flathead screwdriver.
Ø35
A
A = snap-in pin
6

Disassembling the plug-in connecting cable for tubular drives dia. 45 and dia. 58
Caution
Prior to disassembly, the power supply to the connecting cable must be disconnected.
On drives with a diameter Ø45 or Ø58, insert a suitable flathead screwdriver right into the recess of the locating latch, so that the
latch releases the locating lug from the plug.
Now you can pull out the connecting cable along with the flathead screwdriver.
dia. 45 and dia. 58
1.
2.
A
A = locating latch
7

Installation
Assembling the drive
Attention
To connect the drive to the driven part, solely mechanical accessory components made by
the drive manufacturer from the current product catalogue may be used.
Prior to mounting, the fitter must ensure that the masonry and the system being motorised are sufficiently robust (drive torque plus
weight of the shading solution).
Caution
Electrical connections may only be carried out by a qualified electrician. Prior to assembly,
the power supply must be disconnected and secured. Please give the enclosed connection
information to the responsible electrical contractor.
These drives cannot be operated with conventional switching elements (switches, timers
and the like).
Calculate the space required at the side (M) by measuring the drive head and wall
bracket. The clear dimension of the box (X) minus the space required at the side (M)
and idler (G) gives the length (L) of the barrel: L=X-M-G.
The space required at the side (M) varies depending on the combination of drive and
wall bracket.
Then mount the wall bracket and idler. Ensure that the barrel is aligned at right angles to the wall and that sufficient axial play is al-
lowed for the mounted system.
Undoing the mounting pin
When pushed in, the mounting pin (2) locks automatically. To undo the mounting pin
(2), push the tab washer (1) upwards and pull out the mounting pin (2).
Assembling the drive adapter with drive adapter safety catch
Put the drive adapter (1) onto the drive shaft of the tubular drive. You can see where
to insert the safety catch (2) from its shape. When inserting the drive adapter safety
catch (2) into the hole (4), make sure that the locking lug (3) engages. You will hear a
click. Check that the safety catch is securely in position by pulling on the drive ad-
apter (1).
8

Assembling the drive adapter with screw connection
Put the drive adapter (1) onto the drive shaft of the tubular drive. For the assembly,
use an M6 x 12 screw (3) with appropriate washer (2) and suitable screw retainer.
Threaded hole (4)
Securing the drive against axial displacement
In order to secure the drive against axial displacement, we recommend screwing the
drive adapter to the tube.
Attention
When drilling into the barrel, never drill near the tubular drive!
Fixing the drive adapter to the barrel dia. 35 and dia. 45 and dia. 58
Size of drive
[mm]
Diameter of barrel
[mm]
Torque
max. [Nm]
Fastening screws
for drive adapter (4 pc.)
dia. 35 40 mm plastic drive adapter 13 Self-tapping screw
dia. 4.8 x 9.5mm
dia. 45 50-70mm plastic drive adapter 25 Self-tapping screw
dia. 4.8 x 9.5mm
dia. 45 50-85mm plastic drive adapter
for obstacle detection
40 Self-tapping screw
dia. 4.8 x 9.5mm
dia. 45 50 - 85 mm diecast drive adapter 50 Self-tapping screw
dia. 4.8 x 9.5mm
dia. 58 85-133mm aluminium drive adapter 120 Countersunk screw
M8 x 16mm
dia. 58 63-120mm diecast drive adapter 120 Self-tapping screw
dia. 6.3 x 13mm
We also recommend screwing the idler to the barrel.
Attention
Do not hammer the tubular drive into the tube or drop it into the barrel! The curtain can only
be secured using springs or anti-lifting devices.
9

Mounting the drive in the tube
For profile tubes:
In the case of some drive adapters, tolerances of the groove widths in different bar-
rels can be offset by rotating the drive adapter into a different groove recess. These
groove recesses have different sizes and allow the drive to fit exactly.
For round tubes:
First notch the tube on the motor side, so the lug of the thrust ring can also be pushed
into the tube. There must be no play between the lug of the thrust ring and the tube.
4,5mm
Assemble the tubular drive with the relevant thrust ring (1) and drive adapter (2). In-
sert the tubular drive with the pre-assembled thrust ring and drive adapter into the
tube to achieve a form fit. Ensure that the thrust ring and drive adapter are secure in
the tube.
Mount the assembled unit comprising barrel, tubular drive and idler on the box and secure the drive according to the type of wall
bracket fixing with a split or spring pin.
Lay the connecting cable
Lay the connecting cable up to the tubular drive, and fix The connecting cable and
any antennae must not project into the winding chamber. Cover any sharp edges.
Confirming the drive
The drive audibly confirms each programming and deletion action. The tubular drive makes a barely perceptible movement, which
you hear as a “click" or "click click" sound.
10

First operation
Explanation of symbols
Retract button
STOP button
Extend button
Programming button
The tubular drive clicks once to confirm
The tubular drive clicks twice to confirm
The tubular drive clicks 3times to confirm
1 = direction switch
2 = radio switch
Attention
The tubular drives are designed for short-time operation. An inbuilt thermal protection
switch prevents overheating of the tubular drive. During commissioning (long drop dis-
tance or long running time), the thermoswitch may trigger. The drive will switch off. After a
short cooling-down period, the system is ready for operation again.
The drive does not achieve its full duty cycle until it has cooled to ambient temperature.
Avoid a situation where the thermal protection switch cuts in repeatedly.
N1
2
1
2
4
3
4
230V AC / 50 Hz
L1
PE
Connecting the tubular drive
Connect the tubular drive to the power supply.
1 = blue 3 = black
2 = brown 4 = green-yellow
Readying the tubular drive for programming
Putting the tubular drive into programming mode by switching on the power
▻Switch on the power.
►The tubular drive is ready to program for 3minutes
11

If several tubular drives are to be connected in parallel, you can deactivate the program-
ming mode on one tubular drive by switching the radio switch to the outside position after
turning the power on.
Readying the tubular drive for programming with the radio switch
Switch the radio switch to the inside position. If the radio switch is already in this posi-
tion, switch it to the outside and back to the inside position.
►The tubular drive is ready to program for 3minutes
Intelligent installation management
Limit position status indicator
A brief stopping and restarting indicates that no limit position has been set in that direction of movement.
Completion of installation following automatic setting of limit positions
The drive saves the limit position permanently once the upper limit position is reached 3 times in succession. Installation is then
complete. If the limit position is set above a point, this is stored permanently.
Programming the master transmitter
Press the programming button for 3 seconds when it is ready to programme.
▻The tubular drive makes a clicking sound to confirm.
►The programming process is now complete.
If a transmitter is already programmed on the receiver, press the programming button for
10 seconds.
Checking that the running direction is correct
There are 2 ways to change the direction of rotation
•Changing direction of rotation via the direction switch
•Changing direction of rotation via the master transmitter
Changing direction of rotation via the direction switch
Press the UP or DOWN button
▻The shading solution runs in the desired direction
►The running direction is OK.
If the shading solution runs in the wrong direction, the running direction must be switched. Proceed as follows:
Switch the direction switch (1) to the opposite position.
▻The running direction will now have changed.
►Check the running direction again.
12

Changing direction of rotation via the master transmitter
It is only possible to change the direction of rotation if no limit position has been set.
Press the UP or DOWN button.
▻The shading solution runs in the desired direction.
►The running direction is OK.
If the shading solution runs in the wrong direction, the running direction must be switched. Proceed as follows:
Press the programming button and, within the next 3seconds, also press both the UP
and DOWN buttons. Hold down the buttons for 3seconds.
►The tubular drive clicks 3times to confirm.
Check the running direction again.
Setting the limit positions
The limit positions can only be set with the master transmitter. The shutter direction must
be correct. When setting the limit positions, the tubular drive runs in dead-man mode and
limit position status indicator. The extended limit position must always be set first. If the
tubular drive switches off prematurely while extending/retracting, due to an obstruction,
the obstruction can be cleared by extending/retracting the screen and removing the ob-
struction. The upper limit position can be set by extending/retracting again.
There are 2 ways to set the limit positions:
•Extended position to retracted position without stop
•Extended position to retracted stop
The limit position becomes fixed after the tubular drive has turned off automatically in the desired position three times.
Extended position to retracted position without stop
There is no curtain length adjustment with this limit position setting.
Open to the desired extended limit position.
Press the programming button and, within 3 seconds, also press the extend button
and hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
Then close to the desired retracted limit position.
Press the programming button and, within 3 seconds, also press the retract button
and hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
►The limit positions are now set.
13

Extended position to retracted stop
Open to the desired extended limit position.
Press the programming button and, within 3 seconds, also press the extend button
and hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
Then retract to the permanent stop.
▻The tubular drive switches off automatically.
►The limit positions are now set.
Changing the set limit positions
Once set, the limit positions can only be changed with the master transmitter.
1) Shortening the range of travel (the desired limit position is located inside the current range of
travel)
Open/close to the desired new limit position.
Press the programming button and, within 3 seconds, also press the extend button
for the extended limit position or the retract button for the retracted limit position and
hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
►The new limit position is now saved.
2) Extending the range of travel (the desired limit position is located outside the current range of
travel)
Attention
When both or individual limit positions are deleted, all the other set functions (intermediate
position I, intermediate position II) are deleted as well.
Open/close to the limit position in the direction in which you wish to extend the range
of travel.
Press the programming button and, within 3 seconds, also press the STOP button
and hold the two buttons down for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The limit position is now deleted.
Open/close to the desired new limit position.
Press the programming button and, within 3 seconds, also press the extend button
for the extended limit position or the retract button for the retracted limit position and
hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
►The new limit position is now saved.
14

Deleting the limit positions
Attention
When both or individual limit positions are deleted, all the other set functions (intermediate
position I, intermediate position II) are deleted as well.
Once set, the limit positions can only be deleted with the master transmitter.
Deleting individual limit positions
Open/close to the limit position to be deleted.
Press the programming button and, within 3 seconds, also press the STOP button
and hold the two buttons down for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The limit position is now deleted.
Deleting both limit positions
Open/close the curtain to a point between the limit positions.
Press the programming button and, within 3 seconds, also press the STOP button
and hold the two buttons down for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The limit positions are now deleted.
Intermediate positions I + II
The intermediate positions I + II are freely selectable positions for the shading solution
between the two limit positions. Each travel button can be assigned one intermediate posi-
tion. Both limit positions must be set before the intermediate position is set.
Setting the desired intermediate position
Open/close the shading solution to the desired intermediate position.
Press the STOP button and, within 3 seconds, also press the desired travel button
and hold the two buttons down.
▻The tubular drive makes a “click” sound to confirm.
►The intermediate position is now saved.
Setting the desired intermediate position
Press the travel button for the desired intermediate position twice within one second.
►The shading solution runs to the intermediate position assigned to the travel but-
ton.
15

Deleting the desired intermediate position
Open/close the shading solution to the desired intermediate position.
Press the STOP button and, within 3 seconds, also press the travel button assigned to
the intermediate position and hold the two buttons down.
▻The tubular drive makes a clicking sound to confirm.
►The intermediate position is now deleted.
Programming additional transmitters
In addition to the master transmitter, up to 15 further transmitters can be programmed in
the tubular drive. Before programming a radio controlled Sun-Wind-Sensor, the limit posi-
tions must be programmed.
Press the programming button of the master transmitter for 3 seconds.
▻The tubular drive makes a “click” sound to confirm.
Now press the programming button of a new transmitter which has not yet been pro-
grammed in the tubular drive for 3 seconds. Doing so activates the programming
mode of the tubular drive for a new transmitter for 3 minutes.
▻The tubular drive makes a “click” sound to confirm.
Now re-press the programming button of the new transmitter you wish to programme
for 3 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The new transmitter is now programmed in.
Deleting transmitters
Deleting individual transmitters
The programmed master transmitter cannot be deleted. It can only be overwritten (see
Programming the master transmitter [}12]).
Press the programming button on the master transmitter for 3 seconds.
▻The tubular drive makes a “click” sound to confirm.
Now press the programming button of the transmitter to be deleted for 3 seconds.
▻The tubular drive makes a “click” sound to confirm.
Then re-press the programming button of the transmitter to be deleted for 10
seconds.
▻The tubular drive makes a clicking sound to confirm.
►The transmitter is now deleted from the tubular drive.
16

Deleting all transmitters (except the master transmitter)
Press the programming button on the master transmitter for 3 seconds.
▻The tubular drive makes a “click” sound to confirm.
Re-press the programming button on the master transmitter for 3 seconds.
▻The tubular drive makes a “click” sound to confirm.
Re-press the programming button on the master transmitter for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►All transmitters (except the master transmitter) are now deleted from the re-
ceiver.
Overwriting the master
There are two ways to overwrite the master:
•Readying the tubular drive for programming by switching on the power
•Readying the tubular drive for programming with the radio switch
Readying the tubular drive for programming by switching on the power
To ensure that the new master transmitter is programmed in the desired tubular drive only,
all other tubular drives which are connected to the same power supply must be deactivated
from the programming mode. To do so, after switching back on the power, execute a drive
or stop command using the transmitter for the given tubular drives or switch the radio
switch from inside to outside. If the radio switch is already in this position, switch it to the
inside and back to the outside position.
N1
2
1
2
4
3
4
230V AC / 50 Hz
L1
PE
Switch off the tubular drive power for 5 seconds, then switch it back on.
▻The tubular drive is ready to programme for 3 minutes.
1 = blue 3 = black
2 = brown 4 = green-yellow
Now press the programming button of the new master transmitter for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The new master transmitter is now programmed and the old master transmitter
overwritten.
17

Readying the tubular drive for programming with the radio switch
Switch the radio switch to the inside position. If the radio switch is already in this posi-
tion, switch it to the outside and back to the inside position.
▻The tubular drive is ready to programme for 3 minutes.
Now press the programming button of the new master transmitter for 10 seconds.
▻The tubular drive makes a clicking sound to confirm.
►The new master transmitter is now programmed and the old master transmitter
overwritten.
Disposal
This product is made of various materials which must be disposed of properly. Find out about the applicable regulations on recyc-
ling or disposal for this product in your country.
The packaging material must be disposed of properly.
Maintenance
These drives are maintenance-free.
Technical data dia. 35
Type P5/20C
PSF
P5/30C
PSF
P9/16C
PSF
Rated torque [Nm] 5 5 9
Output speed [rpm] 20 30 16
Limit switch range 64revolutions
Supply voltage 230VAC / 50Hz
Connected load [W] 115 115 110
Rated current consumption [A] 0.47 0.47 0.47
Operating mode S24min
Degree of protection IP44
Min. tube inside diameter [mm] 37
Frequency 868.3MHz
Emission sound pressure level [dB(A)] ≤70
18

Technical data dia. 45
Type R8/17C PSF R12/17C
PSF(+)
R20/17C
PSF(+)
R30/17C
PSF(+)
R40/17C
PSF(+)
R50/11C
PSF(+)
Rated torque [Nm] 8 12 20 30 40 50
Output speed [rpm] 17 17 17 17 17 11
Limit switch range 64 revolutions
Supply voltage 230 V AC / 50 Hz
Connected load [W] 100 110 160 205 260 240
Rated current consumption
[A]
0.45 0.50 0.75 0.90 1.15 1.10
Mode S2 4 min
Degree of protection IP 44
Min. tube inside diameter
[mm]
47
Frequency 868.3 MHz
Emission sound pressure
level [dB(A)]
≤ 70
Technical data dia. 58
Type L44/14C PSF(+) L50/17C PSF(+) L60/11C PSF(+) L60/17C PSF(+)*
Rated torque [Nm] 44 50 60 60
Output speed [rpm] 14 17 11 17
Limit switch range 64 revolutions
Supply voltage 230 V AC / 50 Hz
Connected load [W] 255 315 265 380
Rated current consumption
[A]
1.20 1.40 1.20 1.75
Mode S2 4 min
Degree of protection IP 44
Min. tube inside diameter
[mm]
60
Frequency 868.3 MHz
Emission sound pressure
level [dB(A)]
≤ 70
19

Type L70/17C PSF(+) L80/11C PSF(+) L60/17C PSF(+)* L120/11C PSF(+)
Rated torque [Nm] 70 80 80 120
Output speed [rpm] 17 11 17 11
Limit switch range 64 revolutions
Supply voltage 230 V AC / 50 Hz
Connected load [W] 430 310 470 435
Rated current consumption
[A]
1.90 1.40 2.10 1.90
Mode S2 4 min
Degree of protection IP 44
Min. tube inside diameter
[mm]
60
Frequency 868.3 MHz
Emission sound pressure
level [dB(A)]
≤ 70
*) This tubular drive is not yet available.
What to do if...?
Problem Remedy
Tubular drive is not functioning. Program new transmitter.
Bring transmitter within range of the tubular drive.
Press drive or stop button on transmitter at least 5times in the
immediate vicinity of the tubular drive.
Insert batteries correctly or insert new batteries.
Check electrical connection.
Thermal protection switch in tubular drive has tripped. Wait until
the thermal protection switch in the tubular drive is reactivated.
Shutter direction on tubular drive cannot be set. Delete limit positions (see Deleting the limit positions [}15])
and reset the shutter direction.
Incorrect shutter direction after deleting limit positions. Change the shutter direction using the master transmitter or
the direction switch on the tubular drive.
Tubular drive stops arbitrarily; cannot be restarted in the same
direction.
Tubular drive has detected an increase in load. Briefly run the
curtain in the opposite direction, then continue in the desired
direction.
Tubular drive is overloaded. Use a higher-torque tubular drive.
20