Beef Eater DISCOVERY 1100S User manual

Assembly and Operating Instructions
FOR OUTDOOR USE ONLY
D I S C O V E R Y
1100 SERIES
1100S, 1100E, 1100
2, 3, 4 OR 5 BURNERS
AUSTRALIA / NEW ZEALAND

2
CONTENTS
Important safety instructions .......................................................3
Product description ......................................................................6
Assembling the barbecue ........................................................... 7
Using your barbecue ................................................................... 8
Product description for trolley .................................................. 10
Assembling the trolley............................................................... 11
Technical information ................................................................ 15
Locating your barbecue............................................................. 16
Gas specifications ...................................................................... 17
Troubleshooting notes ............................................................... 20
Notes .......................................................................................... 21
Warranty .....................................................................................23
Please read the user manual carefully and store in a handy
place for later reference.
The symbols you will see in this booklet have these
meanings:
WARNING
WARNING
This symbol indicates information concerning your
personal safety.
WARNING
CAUTION
This symbol indicates information on how to avoid damaging
the appliance.
TIPS & INFORMATION
IMPORTANT
This symbol indicates tips and information about use
of the appliance.
ENVIRONMENTAL TIPS
ENVIRONMENT
This symbol indicates tips and information about economical
and ecological use of the appliance.
Dear customer,
Congratulations and thank you for choosing our barbecue.
We are sure you will find it a pleasure to use. Before you use
the barbecue, we recommend that you read through the
relevant sections of this manual, which provide a description
of your appliance and its functions.
To avoid the risks that are always present when you use
an appliance, it is important that the appliance is installed
correctly and that you read the safety instructions carefully to
avoid misuse and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the appliance, please check it is not
damaged. If in doubt, do not use the appliance but contact
your local customer care centre.
This appliance complies with requirements of Australian
Standards AS4557.
Conditions of use
These important notes apply to your appliance
• This appliance must be serviced only by a qualified
licenced person.
• This product is intended for personal, domestic or
household use only, not commercial use.
• This product is intended for outdoor use only.
• This product must be installed, operated and maintained
as per the instructions.
• Ventilation holes in the unit must not be obscured by the
installation.
Please ensure you read the instruction manual fully
before you call for service, or a full service fee could
be applicable.
Record model and serial number here:
Model number: ...............................................................................
Serial number: ................................................................................
PNC: ................................................................................................
CONTENTSCONGRATULATIONS

3SAFETY
Please read the user manual carefully and store in a handy
place for later reference.
TIPS & INFORMATION
IMPORTANT
Important – check for any damages or marks
If you find the barbecue is damaged or marked, you must
report it within 7 days if you wish to claim for damage/marks
under the manufacturer’s warranty. This does not affect
your statutory rights.
ENVIRONMENTAL TIPS
ENVIRONMENT
Information on disposal for users
• Most of the packing materials are recyclable.
Please dispose of those materials through your local
recycling depot or by placing them in appropriate
collection containers.
• If you wish to discard this product, please contact
your local authorities and ask for the correct method
of disposal.
WARNING
WARNING
This appliance must be serviced only by a qualified
licensed person.
Improper installation, adjustment, alteration or
maintenance can cause injury or property damage.
Please contact your nearest BeefEater Service
Department for additional information or assistance
for an approved installer.
Note to the installer
This manual must remain with the owner for future reference.
WARNING
WARNING
• Do not lean over barbecue when lighting.
• Do not leave the barbecue unattended when alight.
• Do not delay lighting once the gas has been turned on.
• Do not store or use aerosol cans in the vicinity of
the barbecue.
• Do not store flammable liquids in the vicinity of
the barbecue.
• Do not use caustic or abrasive based cleaners on
the barbecue.
• Do not attempt to dismantle or adjust the control valves.
• Do not attempt to dismantle or adjust the regulator.
• Do not test for leaks with a naked flame.
• Do not modify the construction of this appliance or
modify the injector orifice size.
• Do not obstruct any ventilation of the barbecue.
• Do not allow children to operate or play near
the barbecue.
WARNING
CAUTION
This appliance is set up for Universal LPG and is labelled
accordingly. A natural gas conversion kit is available if
required. Conversion of this unit to natural gas must be
carried out by a qualified licensed person and a Certificate of
Compliance must be issued to the owner at the completion
of the installation and conversion.
TIPS & INFORMATION
IMPORTANT
BeefEater Barbecues are approved for OUTDOOR USE ONLY
and must not be used in a building, garage or any other
enclosed area.
• BeefEater Barbecues must not be used inside
recreational vehicles or boats.
• Read instructions thoroughly before operating this
Barbecue.
• Save this manual for future reference.
• Always use the Barbecue on a flat, level surface.
• Some foods produce flammable fats and juices. Regular
cleaning is essential.
• Attend an operating barbecue at all times. Damage
caused by fat & grease fires is not covered by warranty.
• When not in use keep Barbecue dry and covered.
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open hood.
4. If odour continues, immediately call your gas supplier
or your fire department.
For your safety
1. Do not store or use gasoline or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. An LPG cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
IMPORTANT SAFETY INSTRUCTIONS

4SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
Failure to follow these instructions and observe the
warnings provided in this operations manual could result in
fire, explosion or burn hazard, which could cause property
damage, personal injury or death.
Gas vapour is highly explosive and can cause serious bodily
injury or damage to property if allowed to accumulate in a
confined space and ignited.
This appliance must not be installed under or on any
combustible material. Minimum clearance from combustible
materials to all sides of the appliance is 450mm (18”).
These instructions must be left with the owner.
NOTE:
1. Do not use gas other than the type specified on the
Data Plate.
2. The appliance is designed for use by adults, keep
children away from the 1100Series BBQ at all times.
3. Use only on a flat, level, stable non-combustible surface.
Do not use this appliance on any surface that can burn
or melt.
4. When in use, gas cylinder should be kept at designated
mountings on 1100Series BBQ, and supply hoses kept
away from any hot surfaces.
5. To prevent accidental fires, before using the appliance
ensure that there is no apparent damage to hose and
regulator and all joint connections are in good order and
not leaking.
6. Use a soapy water solution on all joints in order to check
for leaks. If bubbles appear, it indicates that there is a
leak and the appliance must not be used.
7. LPG cylinder, regulator and hose must comply with
national standards.
8. Do not move or attempt to move the appliance while in
operation.
9 Do not operate this appliance before leak checking
hoses and gas cylinder connection.
To the installer
• For fixed installations, in Australia refer also to the
requirements of AS5601/AG601, local authority, gas,
electricity, and any other relevant statutory regulations.
• For fixed installations, refer to AS 5601/AG 601 for pipe
sizing details.
• Consult other trades. Where required, consult a
bricklayer or an electrician for parts of the installation
that could have an effect on these areas.
• Allow a 20mm gap from back of barbecue body for
ventilation and air access.
• Test appliance for correct operation before leaving, and
instruct user on its use.
• If correct operation cannot be achieved, disconnect
barbecue from gas supply, and contact your nearest
BeefEater dealer.
• Please only use BeefEater supplied hose(s) to connect
this appliance. Natural Gas conversion kits are available
from your nearest BeefEater dealer.
Do not
• Lean over barbecue when lighting.
• Leave cooking food unattended.
• Delay lighting burners after turning gas on.
• Spray or store aerosols in vicinity of barbecue whilst
in operation.
• Store combustible materials, gasoline or flammable
liquids or vapours within 450mm (18”) of barbecue.
• Use caustic based cleaning agents on the barbecue.
• Operate barbecue with any cover on.
• Use plastic or glass utensils on the barbecue.
• Operate barbecue in strong winds.
• Attempt to dismantle control valves.
• Attempt to dismantle or adjust regulator.
• Test for gas leaks with a naked flame.
• Store gas cylinder indoors, or in any enclosed area.
• Lay the gas cylinder down. Always keep it upright.
• Use barbecue indoors.
• Expose hose to direct sunlight.
• Modify the construction of this appliance or the size of
any burner or valve orifice.
• Move the appliance during use.
• Obstruct any ventilation of barbecue or the cylinder.
• Allow the flexible gas supply hose or any electrical cord
to come in contact with hot surface of the appliance.

5SAFETY
IMPORTANT SAFETY INSTRUCTIONS
• Allow children to operate this appliance.
• Use charcoal or any other solid fuel in this appliance.
• Disconnect any gas fittings while the appliance
is operating.
• Use a rusty or dented gas cylinder or cylinder with a
damaged gas valve.
• Fill the gas cylinder beyond 80% capacity.
• Touch some accessible parts, other than the ones meant
for handling. They may be hot.
Do
• Spanner tighten all gas fittings as per instructions.
• Check all gas hoses and line connections for damage,
cuts or cracks each time the appliance is about to
be used.
• Always leak test with a solution of soapy water.
• Check main opening, throat and venturi to each burner
and pilot flame tube regularly for insect nests (eg. wasp,
ants or spiders). Nests are dangerous and must be
cleaned out thoroughly.
• Visually check burner flames to confirm lighting.
• Use your barbecue only on a level surface.
• Attend barbecue whilst cooking food.
• Preheat the barbecue for up to 10 minutes.
• After cooking turn barbecue to high for up to 10 minutes
to burn off excess grease.
• Let the barbecue cool before replacing any lid or cover.
• Regularly replace foil material in grease/drip tray.
• Keep children away from barbecue at all times.
• Have the gas cylinder filled by an authorised
LPG supplier.
• Refer to this instruction manual if in doubt concerning
assembly, installation, or operation.
• Use protective gloves when handling hot components.
• Close the gas cylinder valve after each use.
• Clean the grease/drip tray regularly and clean the
appliance at least twice annually.
• Always remove any lid or cover off the appliance
before lighting.
• Carefully follow the instructions relating to the hose/
regulator connection.
• Keep the barbecue area free from combustible
materials, gasoline, flammable liquids or vapours.
TIPS & INFORMATION
IMPORTANT
Should the appliance go out for any reason, turn off all
control knobs and the cylinder gas valve. Wait 5 minutes
before attempting to relight the appliance.
• If a grease or fat fire should occur, immediately turn off
all control knobs and the gas cylinder valve until the fire
is out. Remove all food from the appliance.
• A leak test must be carried out prior to using the
appliance for the first time and whenever the gas
cylinder is refilled or whenever the gas hose and
regulator have been disconnected from the gas cylinder
or appliance.

6
PRODUCT DESCRIPTION
PRODUCT DESCRIPTION
1
8
2
3
7
4
6
5
11
10
9
1 BBQ Body
2 Hood
3 Cooking Grill
4 Cooking Plate
5 Side Burner
6 Warming Rack
7 Rotisserie Bracket*
8 Cabinet Trolley**
9 Vaporizers
10 Burner
11 External Baskets***
* Rotisserie is sold separately
** Trolley is packed in a separate carton
*** May not be included with all models
Images in this manual are for illustrative purposes only. Due to constant improvement, BeefEater advises that changes to the design, material, specifications and
product configuration may occur at any time without notice.

7ASSEMBLY
ASSEMBLING THE BARBECUE
ASSEMBLY
General
This barbecue can be mounted onto a mobile trolley.
The Trolley is packed in a separate carton. Please refer to
the Trolley instruction booklet for assembly of the trolley, and
barbecue mounting.
Once the barbecue had been properly installed, please check
the following:
1. Hood is fully engaged into the four slots in the
barbecue’s body.
2. All burners are in place correctly and secure by an
‘R’ clip:
3. Vaporizers are installed individually on the steps
above burners, but under the Grill (not required under
the Plate). They are inserted into the positioning slots
like this:
4. Cooking surfaces (Grill and Plate) are clean, and
installed over the burners and vaporizers.

8
USING YOUR BARBECUE
USING YOUR BARBECUE
Before you light the barbecue
Perform the following checks:
• Make sure all connections are tight, and leak-tested.
Gas regulators fitted with a hand-tightened wheel must
be checked to ensure they are secured.
• Check that all control knobs are in the ‘Off’ position, and
that gas supply is turned off.
• Ensure that the Hood on the barbecue, and the Lid
on the side-burner are open. If lids are closed there
is a risk of gas accumulating inside, and creating a
dangerous situation.
• The hose and regulator supplied with this barbecue
must be used at all times whilst operating this
barbecue. Inspect the hose and regulator regularly
for cracks or any sign of damage. If there is excessive
abrasion or wear, replace only with a genuine
BeefEater regulator.
• The bottom panel of the Barbecue is clean and free of
any fat or other food residue.
Grease collecting pan
The grease Collecting Pan is located on 2 brackets below the
barbecue’s bottom panel, on the left-hand-side.
Make sure the pan is always in its place when operating the
barbecue, to avoid fat dripping directly into the trolley. Make
sure the grease pan is emptied and cleaned regularly.
Also ensure the grease is cleaned off the bottom of the
Barbecue before each use.
Lighting the Barbecue
• Ensure the appliance is placed on a flat, level,
non-combustible surface.
• Ensure the regulator is connected to the LPG cylinder
(See Regulator Connection page 4.), and the hose is not
subject to any twisting, and is not close to hot surfaces.
• Verify all joints are spanner tight and check for leaks
after turning on gas supply.
• Ensure all knobs are in the ‘Off’ position.
• Ensure vaporizers, cooking plate and grill are in place.
• Open Gas Cylinder valve.
NOTE: The barbecue is fitted with a safety feature that
prevents the burners from being accidentally turned on.
You must push the knob inwards to disengage the lock, and
only then start turning it.
Light each burner by following this procedure:
• Read all instructions before lighting.
• Open Hood before lighting.
• Push in and turn Right-Hand-Side knob counter-
clockwise to ‘High’.
• If ignition does not occur, return to ‘Off’ and repeat after
5 minutes.
Check for a clear blue flame with just a tip of yellow.
Once the right-hand-side burner is alight, light each
successive burner from right to left.
WARNING
WARNING
Excess yellow tipping means the combustion is not right, if
that is observed, turn the Barbecue burners off, and refer to
troubleshooting at the end of this manual.
Do not use more than 2 burners on ‘High’ with the
hood closed.
If the burner does not light
Keep the control knob pushed, and return the knob in the
clockwise direction to the ‘Off’ position. Wait 5 minutes, and
repeat the lighting procedure steps 1 – 4 above again.
If after a few attempts you still can not light the burners,
contact your retailer before proceeding.
Manual Lighting
Press and turn the right hand control knob anti-clockwise
to the ‘High’ position, then, using a long match, light the
right hand burner immediately through the cooking grill
and vaporizer.
Check for proper burner operation
Following operating instructions light each burner and
check for a clear blue flame with just a tip of yellow. Excess
yellow tipping can be adjusted using the screw on the side
of the burner. If you are unable to achieve correct operation,
consult your dealer.
Preparing the Plate and Grill:
Your barbecue has heavy duty enamelled Cast Iron plate
and grill. Enamel is a hard, non-rusting surface which will
ensure the long life of your cooking surface.
The plate and grill are ready to use, but it is recommended
to wash them with warm soapy water and a soft cloth, and
rinse before use.
To ensure the longevity of the enamel surface on the Cast
Iron plate and grill it is strongly advised to avoid impact with
other metal parts and sharp utensils.
To turn off a burner
Simply turn the knob (without pushing) clockwise to the
‘Off’ position.

9
USING YOUR BARBECUE
USING YOUR BARBECUE
After Use
It is a good idea to leave the barbecue on for about
10 minutes after you have finished cooking. This helps to
burn away any excess food residues and oil, and makes
cleaning easier.
1. Be sure to turn off all control knobs and the gas supply.
2. Allow the barbecue to cool.
3. Clean the drip tray and cooking surfaces. Clean any food
spills from the side burner, if one is installed.
4. Lower the hood and side burner lid.
The gas cylinder supply valve must be turned off when the
appliance is not in use.
Direct Cooking Method
Commonly used for traditional barbecuing. Place food over
the lit grill section. Some flaring may occur, so care must
be taken while cooking. Check inside the roasting hood
regularly. The direct cooking method is recommended for
steaks, chops, sausages, and hamburgers.
Indirect Cooking
Indirect cooking involves little or no heat directly underneath
the food. Instead, the food is placed on the grill, the burners
below the food are turned off or Low, and burners on either
side are used. The hood is closed to trap heat and moisture.
With this method, heat circulates around the food, cooking
by convection. By trapping the vapour inside your “outdoor
oven”, the cooking vapour will fall back on the food on all
sides, not just from underneath. The food cooks more evenly,
and stays moist in the process. Indirect cooking is similar to
using a conventional oven and is recommended for rotisserie
cooking, roasts, poultry, casseroles, vegetables and whole
fish. When cooking a roast, it is a good idea to use a roast
holder and baking dish. Always use a baking dish with a
depth greater than 35mm. Shallower trays may fill quickly
and overflow, which may cause a fat fire.
Controlling the Burners
The control knob can now be turned to the desired heat
setting, Low, High or anywhere in between. The control
knob does not need to be pushed in while selecting the heat
setting.
Storing Your Barbecue
When storing barbecue for extended periods, be certain all
controls and cylinder valves are turned off. If storing the
barbecue indoors remove gas cylinder and store the cylinder
in a ventilated area outdoors. Gas cylinders must be stored
outdoors, out of reach of children and must not be stored in
a building, garage or any other enclosed area. The barbecue
should be covered when not in use eg. with a polyester or
vinyl barbecue cover.

10 PRODUCT DESCRIPTION FOR TROLLEY
PRODUCT DESCRIPTION FOR TROLLEY
6
14
13
8
7
3
9
5
15
10
4
16
11
1
2
1 Base Panel
2 Right Hand Side Panel
3 Left Hand Side Panel
4 Rear Panel
5 Top Front Brace
6 Left Hand Side Door
7 Right Hand Side Door
8 Door Handle x 2
9 Side Shelf
10 Side Burner
11 Wheels Axel x 2
12 Wheel x 2
13 Wheel Hub Cap
14 Castor x 2
15 Door Hinge x 2+2
16 Condiment Basket
(optional)
Bolt pack content
A Circlips x 2
B M6 x 12 screw x 29
C M6 washer x 33
D M5 x 10 countersunk screw x 8
E Rubber grommet x 2
F Fiber washer x 8
G M6 x 25 screw x 8
H Magnets x 4
I Gas hose x 1
12

11ASSEMBLY
ASSEMBLING THE TROLLEY
1. Turn the Base Panel upside-down, insert the Wheel Axel
through the 2 holes, and place a wheel on each side.
Secure with a circlip on outside of wheel. Place Cap.
insert each castor to its place in the other 2 corners.
2 x ‘A’
2. Turn the base back upright, and attach the side and
back panels. Insert grommet in side and rear panel
holes. Insert magnets.
13 x ‘B’, 13 x ‘C’, 2 x ‘E’, 2 x ‘H’

12 ASSEMBLY
ASSEMBLING THE TROLLEY
3. If required, attach the hinge blocks to front of side
panels. Note: the block should be on the inside, with
only the small bends protruding out.
8 x ‘D’
4. Attach the Top Brace. Do not tighten. That will be done
after fitting the doors. Insert magnets.
4 x ‘B’, 4 x ‘C’, 2 x ‘H’

13ASSEMBLY
ASSEMBLING THE TROLLEY
5. Hold each door at ~60° open angle, and insert through
opening at door internal skin over the hinge block
pins. Ensure correct engagement in both brackets
simultaneously.
Secure the Cylinder Shield (if included) in place on top,
RH side of trolley.
6. Remove all loose parts from inside the Barbecue. Place the
Barbecue over the trolley and attach with screws. Ensure
the lugs in the middle of trolley side panels engage with
corresponding slots in BBQ body.
Fit cylinder mounting hook into slot of side panel as shown.

14 ASSEMBLY
ASSEMBLING THE TROLLEY
7. Adjust the Top Brace (from step 4) to right position, so
the doors are closing straight, and tighten the 4 screws.
8. Fit the shelf and Side Burner (or 2 shelves) to the side
of the Barbecue. Note: screws to go from the inside of
barbecue body out.
8 x ‘G’, 8 x ‘F’
9. Disconnect hose and regulator assembly at connection point
A as shown below.
Connect hose included with product at point A, feed through
hole in side of trolley (ensure grommet is fitted) and connect
to point B of side burner manifold.
AB

15
CONTENTS
ASSEMBLING THE TROLLEY
10. Connect hose and regulator assembly to point C of side
burner manifold as shown below and the other end to
the gas cylinder.
PERFORM LEAK TEST ON ALL CONNECTION POINTS
BEFORE PROCEEDING FURTHER
B
C

16 TECHNICAL INFORMATION
TECHNICAL INFORMATION
NOTE: Do not modify this appliance. Any deviation from
factory settings could result in a safety hazard.
Barbecue manifold inlet thread: 3/8 SAE male flare fitting.
Gas Pressure:
LPG – 2.75 Kpa; 11”WC
NG – 1.0 Kpa; 4” WC
Main barbecue
Gas Nozzle size:
LPG – 01.15mm;
NG – 01.90mm;
Gas Input: AU: 17Mj/Bnr
NA: 15,500BTU
Side burner
Nozzle size:
LPG – 1.05mm;
NG – 1.7mm;
Gas Input: AU: 15Mj/Bnr
NA: 13,000BTU
3B = 1409mm
4B = 1569mm
5B = 1726mm
3B = 689mm
4B = 849mm
5B = 1006mm
893mm
1160mm
591mm
514mm
581mm

17LOCATING YOUR BARBECUE
LOCATING YOUR BARBECUE
Most importantly, this is an outdoor appliance. Ensure your
barbecue is positioned safely away from anything that can
catch fire.
Outdoor Use Only
Under no circumstances is this barbecue to be used indoors.
This includes garages or any other enclosed area. Clearance
from Combustibles: Ensure your barbecue remains at
a distance of at least 45 cm (18”) from any combustible
material such as wood, gyprock, paper and plants. Do not
store combustible materials, gasoline or flammable liquids
or vapours within 45 cm (18”) of the barbecue.
Adequate Ventilation
Ensure there is adequate ventilation for both the barbecue
and cylinder. This is required not only for proper combustion,
but also to prevent gas build up. 20mm ventilation and
air-intake gap is to be left at rear of the barbecue in
fixed installations.
Firm Level Surface
Use your barbecue only on a firm level surface.
This barbecue is not designed for recreational vehicles, and
shall not be installed on a boat or any marine craft.
Protection From Weather: Keep the barbecue protected from
adverse weather, including rain and high winds. Polyvinyl
covers are available that have been specially designed for
this range of barbecues. Allow clear access to the entire gas
supply hose and regulator.
Maintenance Access: When your barbecue is installed, you
should be able to access the gas supply line including the
gas piping or hose, gas regulator, gas cylinder and any shut
off valves.
Partial Enclosures: Many backyards have areas that are
partially closed off, such as balconies and pergolas. In some
cases, it is hard to decide whether these partially enclosed
areas should be classified as indoor areas. .
Connect the regulator to the gas cylinder
WARNING
WARNING
Verify ‘Gas Type’ label & data plate attached to side of
barbecue is correct for the gas you are about to connect to.
The hose and regulator is connected to the BBQ and leak
tested at factory. Do not disassemble unnecessarily.
1. Make sure burner valves are in the ‘Off’ position.
2. Screw regulator side to the cylinder, and hand-tighten.
The connected gas cylinder is to be mounted external to the
barbecue using the mounting hook supplied.
Do not store the connected gas cylinder in the compartment.
Do not store spare gas cylinder/s in the compartment or near
the appliance: use only the cylinder storage facility provided.
If this warning is not followed, a fire causing injury or damage
may occur.
In North America, the installation must confirm with local
codes or, in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z223. 1/NFPA 54, Natural
Gas and Propane Installation Code, CSA B149.1, or Propane
Storage and Handling Code, B149.2
NOTE:
• If moving the BBQ from one place to another, never drag
the cylinder behind. Disconnect the cylinder first, move,
and re-connect once reached the new location.
• For storage and cylinder exchange, disconnect hose
at the cylinder only, do not disconnect hose from
the appliance.
• If you have purchased a trolley with a Side-Burner,
please refer to Trolley instruction book for correct
connection of the Side-Burner to the gas supply.
Maintenance
1. Use only soft cloth or sponge to clean the surfaces of
barbecue and then carefully dry.
2. Avoid leaving acidic or alkaline substances on the plate.
It may cause discolouration and corrosion.
3. Keep the igniters probe clean. Wipe away any apparent
water or dirt.
4. Clean the unit after each use to maintain the appearance
and prolong the appliance’s life. Do not use corrosive
materials or harsh detergents to clean the BBQ.
SERVICE AND MAINTENANCE EACH USE 6 MONTHLY EVERY 2 YEARS
Check gas supply hose(s) for cracks and leaks ✓
Check gas regulator for leaks ✓
Check that all gas fittings are tight ✓
Inspect and clean ignition module and probe ✓
Inspect and clean barbecue Burners ✓
Inspect and clean gas injectors ✓
Check gas control valve on cylinder ✓
Inspect gas control valves ✓
Inspect and proof all internal structure barbecue and trolley ✓

18 GAS SPECIFICATIONS
GAS SPECIFICATIONS
Choosing a location
• The vertical clearance above the cooking surface to any
combustible materials must be at least 1000mm.
• Cooking with roasting hood closed vents the hot
flue gases out the rear of the appliance. A minimum
clearance of 450mm to any combustible materials is
required. This clearance should also be maintained for
brittle materials which may be affected, such as glass.
• Avoid windy conditions as this will affect cooking
performance and burner efficiency. If this situation
cannot be avoided some shielding may be necessary.
• This appliance must be installed in accordance with
Australian Standards AS4557 and AS5601 and in
accordance with the local authority.
• Ensure there is sufficient clearance behind barbecue for
hood to open fully.
WARNING
WARNING
• This appliance shall only be used in an above ground,
open air situation with natural ventilation without
stagnant areas, where gas leakage and products of
combustion are rapidly dispersed by wind or natural
convection. This barbecue has been designed for
outdoor use only. Refer to diagrams below.
• Never install this barbecue inside any building,
garage, shed or breezeway or inside a boat, caravan or
recreational vehicle. This is to prevent the possibility of
fire or carbon monoxide poisoning or asphyxiation.
• Any enclosure in which this appliance is installed shall
comply with one of the following:
– An enclosure with walls on all sides, but at least
one permanent opening at the ground level and no
overhead covering
– Within a partial enclosure that includes an overhead
cover and no more than 2 walls
– Within a partial enclosure that includes an overhead
cover and more than 2 walls, the following shall apply:
– at least 25% of the total wall area is completely open
and at least 30% of the remaining wall area is open
and unrestricted
• In the case of balconies, at least 20% of the total of the
side, back and front wall areas shall be and remain
open and unrestricted.
Outdoor area
example 1
Outdoor area
example 2
Outdoor area
example 3
both ends
open
open side at
least 25% of
total wall area
open side at
least 25% of
total wall area
Outdoor area
example 4
Outdoor area
example 5
30% or more
in total of the
remaining wall
area is open and
unrestricted
30% or more
in total of the
remaining wall
area is open and
unrestricted

19GAS SPECIFICATIONS
GAS SPECIFICATIONS
Before proceeding, you need to establish the gas type
which your barbecue will run on, and the style of installation
you need.
Natural gas or LPG/Propane.
Before beginning installation or assembly, check that the gas
type which the barbecue is designed for is correct for the gas
available to you. In most countries the choices are natural
gas or LPG/propane. You will find the gas type label on the
side of your barbecue. If your barbecue uses the incorrect
gas type, or if you are unsure, consult your dealer before
going any further. Using the wrong type of gas for a barbecue
is extremely dangerous.
Natural gas conversion
Most newly purchased barbecues are made for LPG/
propane. A natural gas conversion kit is available to allow
your barbecue to run on Natural Gas. This kit includes all
hoses required for installation.
Service assistance
To assist you when contacting your after-sales service
agent and to arrange for service, please have the barbecue
details ready when you call. You do not need to register your
warranty. However, you must retain your receipt or proof
of purchase. When claiming warranty for this appliance
you must provide a copy of your proof of purchase receipt.
No claims for warranty will be accepted without proof of
purchase. For all parts and service, contact your nearest
BeefEater dealer.
Gas cylinder safety information
• Gas cylinders must be stored outdoors, out of reach of
children and must not be stored in a building, garage or
any other enclosed area.
• This appliance is designed to be used with a gas cylinder
not exceeding 9KG (20lbs) capacity.
• The Gas cylinder must be constructed and marked in
accordance with specifications for LP Gas Cylinders.
• The gas cylinder supply valve must be turned off when
the appliance is not in use.
• The gas cylinder used must incorporate a safety collar to
protect the valve assembly.
• The gas cylinder must always be kept and used in the
upright position.
• Do not store a spare LPG cylinder under or near
this appliance.
• Never fill the cylinder beyond 80 percent full.
• If the information above is not followed exactly, a fire
causing death or serious injury may occur.
TIPS & INFORMATION
IMPORTANT
When disconnecting and removing the gas cylinder for the
purpose of refilling, always observe the following procedure:
• Ensure that all gas control valves on the appliance and
the gas cylinder are turned off before disconnecting the
gas line from the cylinder.
• Do not smoke or use a naked flame near the appliance
or gas cylinder while disconnecting the gas line between
the appliance and gas cylinder.
• Remove the gas cylinder from the enclosure before
disconnecting the gas line from the appliance.
• Tighten all connections before placing the gas cylinder
back in its enclosure.
The Gas Leak Testing Procedure should be conducted
every time.
Regulator connection
1. Check that all control knobs are in the ‘Off’ position.
2. Make sure the cylinder valve is off by turning the valve
knob all the way clockwise.
3. Remove the protective cap from the cylinder if present.
4. Make connection as described in figures 1 and 2.
5. Leak-test the connection with a soapy water solution.
(See Gas Leak Testing Procedure).
Hose and regulator replacement must be a genuine part
specified for this appliance, and can be obtained at your
nearest BeefEater stockist.

20 GAS SPECIFICATIONS
GAS SPECIFICATIONS
Gas leak test procedure
Use the following procedure to check for gas leaks.
Never use a naked flame to check for gas leaks.
FIG 1
Standard POL regulator (AU/NZ regulator)
FIG 2
Quick connect regulator (North America regulator)
1. In a small container, mix up a solution of water and
detergent or soap. Mix the solution well.
2. For LPG make sure that the gas supply valve on the gas
cylinder is turned on. For Natural gas make sure that
the gas line is correctly fitted to the appliance.
3. Make sure that the gas control valves on the appliance
are all turned off.
4. Using a brush or spray bottle apply the solution to the
gas line and each join in the gas line. See Fig 3.
5. Bubbling of the solution will indicate that there is a
leak present.
6. Re-tighten or re-seal any joints that are leaking.
7. If a leak persists then contact your distributor or the
manufacturer for assistance.
FIG 3
Gas shutoff valve
Gas shutoff valve
Bleeder valve screw
Bleeder valve screw
Protector cap
Protector cap
Gas cylinder
Gas cylinder
Regulator and hose
Regulator and hose
Tighten in this direction
Tighten in this direction