Beghelli BoxLED BL736LED Series User manual

1Beluce Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: [phone] Fax: [phone]
FLOODLIGHT LED
BoxLED®
Flood
BL736LED-FL
No user serviceable parts. Refer service to a qualified service
technician. Read instructions prior to installing and/or operating
this device. Installation should be performed by a licensed
electrician/installer in accordance with local codes.
INSTALLATION INSTRUCTIONS
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LUMENS / WATTAGE / DISTRIBUTION /
VOLTAGE / WET LOCATION / WEIGHT / DIMENSION
SERIES: BL736LED
OPERATION: HT (AC ONLY)/0-10V DIMMING
LUMENS: LO (14,000), HO (24,000)
WATTAGE: 150W/230W
DISTRIBUTION: NBD (30°X 40°), WBD(70°),
ASY (70 ° X 30°)
VOLTAGE: 120-277V; 347V
WET LOCATION: IP66
WEIGHT: 17LBS.
DIMENSION: LENGTH: 426.7MM (16.8")
WIDTH: 414MM (16.3")
HEIGHT: 160MM (6.3")
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not let power cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.
4. The use of accessory equipment not recommended by Beluce Canada, may cause an unsafe condition, and will void the warranty.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS!
First make sure power is turned off before starting the installation!
1. Attach and secure mounting brackets to surface using appropriate fasteners.
2. Measure, locate fixture’s position, and mark locations for the brackets.
3. Secure brackets (hardware supplied by others) as shown on next page.
Fixture will snap in place.
926000503

2Beluce Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: [phone] Fax: [phone]
TYPICAL INSTALLATION
BOXLED® FLOODLIGHT
Flood Mount
0-10V dimming wires must be run from a different conduit out of the J-Box.
926000503
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
Mounting bracket
Provided with 18/3 or 18/5 power
cord; 1828.8mm (72")
Mounting hardware
(supplied by others)
Note: For non-dimming, 3-conductor cord is available (upon request).
0-10V LEAD/DALI
Violet (hot)
Grey (negative)
AC LEADS
Black (hot)
White (neutral)
Green (ground)

3Beluce Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: [phone] Fax: [phone]
MOUNTING
BOXLED® FLOODLIGHT
Flood Mounting
1. Attach bracket to housing using hardware as shown below.
a) Drop the hex nut into slot on the side of housing.
b) Roughness washer shall be located between the housing and the bracket.
c) M10 screw shall go through graduated cover and grover washer.
2. Install fixture onto concrete pad/slap as shown (mounting hardware supplied by
others).
3. Loosen M10 screw to adjust the aim angle.
4. Retighten the M10 screw and lock the position up with M5 screw.
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
425.4mm
(16.75")
431.8mm
(17") 11.1mm
(0.4")
149.2mm
(5.8")
50.8mm
(2")
149.2mm
(5.8")
120.6mm
(4.75")
280.1mm
(11")
Flood mount bracket
M5 screw
M10 screw
Hex nut
Roughness washer
Grove washer
Graduated cover
M10 hex socket screw
M5 hex socket screw
Slot for the hex nut
926000503 SAVE THESE INSTRUCTIONS!