Above All LED MT AREA LIGHT User manual

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
1
SUITABLE FOR MODEL
WIRE CONNECTION
SAFETY INSTRUCTION
Maintenance Caution
READ CAREFULLY BEFORE INSTALLING FIXTURE. PLEASE KEEP THIS MANUAL FOR FUTURE USE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
MAKE CERTAIN POWER IS OFF BEFORE INSTALLING OR MAINTAINING FIXTURE.
CHECK THAT VOLTAGE IS COMPATIBLE WITH FIXTURE DRIVER. USE APPROVED CONNECTORS FOR
ALL ELECTRICAL CONNECTIONS.
1. Review the wire connection before beginning, and make sure xture is grounded properly.
2. For lighting controls, follow control instructions carefully.
3. Turn power off and wait for xture to cool before performing maintenance.
4. Maintenance must be done by professionals.
WITH TRUNNION
Universal voltage driver permits operation at
120VAC thru 277VAC or 347VAC or 480VAC, 50
or 60 Hz
WITH ARM OR SLIPFITTER
Universal voltage driver permits operation at 120VAC
thru 277VAC or 347VAC or 480VAC, 50 or 60 Hz

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
2
DRILL PATTERN
POLE MOUNT DRILL PATTERN TRUNNION MOUNT DRILL PATTERN
Threaded hole with UNC #5/16-18,
the depth of thread no longer than 1”
Threaded hole with UNC #5/16-18,
the depth of thread no longer than 1”
2 Places
UNC 3/8-16 Expansion screw
3”
(76.2mm)
WARNING
1. Risk of injury or damage. Make
certain power is OFF before installing
or maintaining xture.
2. If xture is furnished with photocell
receptacle, install the photocell or
shorting cap.
INSTALLATION
Note: If fxture is furnished with photocell receptacle,
please make sure install the photocell or shorting cap
ACCESSORY PACK
WIRE NUT X 3
PHOTOCELL X 1
SHORTING CAP X 1
ACCESSORY PACK FOR PHOTOCELL
ACCESSORY PACK FOR 7 PIN

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
3
SLIPFITTER MOUNT
1. The sliptter ts a 2-3/8’’ O.D. Tenon or Pole. Remove the Sliptter Cover Plate and make necessary wire connections
in the Sliptter and knot wires for strain relief.
2. Place the sliptter over a tenon or pole and secure the xture with (2) Set Screws on the side of the Sliptter.
3. Loosen the Locking Bolt in sliptter to swivel xture to a desired angle. The graduation on the Sliptter Cover Plate can
be used as guidelines to adjust the angle.
4. Tighten the Locking Bolt and replace the Sliptter Cover Plate.
Set Screws
SPECIFIED DIMENSION

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
4
TRUNNION MOUNT
1. Install the trunnion to a desired bracketry by the center hole using (2) Bolts, (2) Locking Washers and (2) Nuts(not sup-
plied) according to the Drill Pattern.
2. Adjust the angle of the xture by trunnion.
3. Feed Fixture Wires through the center opening of Trunnion Bracket along with a Waterproof Bushing (not supplied).
4. Make the necessary wire connections inside the bracketry and knot wires for strain relief.
Notes: Under no conditions should trunnion bolts be torqued to a level from 25 to 32 foot pounds.
ADJUSTABLE ANGLE :-100°~100°(Spacing angle for 10°)

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
5
ROUND POLE ARM MOUNT
Drill the pole according to the drill pattern
1. Feed Supply Wires through the center opening of Pole (not supplied).
2. Secure the Slider on the Pole with (2) Bolts, (4) Curve Washers, (4) Flat Washers sand (2) Nuts. Be sure the Gasket is
between the Slider and Pole.
3. Open the Arm door and slide luminaire arm onto the Slider. Firmly tighten (1) Screw along with washers on the top of
arm.
4. Make necessary wire connections inside the Arm and knot wires for strain relief.
5. Replace the Arm Door and tighten (2) Arm Door Screws.
6. Secure Pole Top Cap (not supplied).

LED MT AREA LIGHT / FLOOD LIGHT
Instruction Manual
Add: 1501 Industrial Way N. Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL, Inc. All rights reserved
6
ROUND POLE ARM MOUNT
Drill the pole according to the drill pattern
1. Feed Supply Wires through the center opening of Pole (not supplied).
2. Secure the Slider on the Pole with (2) Threaded Rod, (4) Curve Washers, (4) Flat Washers and (4) Nuts. Be sure the
Round Pole Adapter is between two Gaskets.
3. Open the Arm door and slide luminaire arm onto the Slider. Firmly tighten (1) Screw along with washers on the top of
arm.
4. Make necessary wire connections inside the Arm and knot wires for strain relief.
5. Replace the Arm Door and tighten (2) Arm Door Screws.
6. Secure Pole Top Cap (not supplied).
Ref#: 10978-10425