Beghelli LEDLUMINA BS400LED User manual

INSTALLATION INSTRUCTIONS
LEDLUMINA BS400LED
Beluce Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: [phone]
F: [phone]
www.BeghelliCanada.com
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600 F:
954 442 6677
www.BeghelliUSA.com
Beghelli Mexico
Av. Del Marqués No. 70, Int. 4
Parque Industrial Bernardo Quintana
C.P. 76246 El Marqués, Qro.
P: [phone] / F: [phone]
www.BeghelliMexico.com

LEDLUMINA
MODEL INFORMATION
IMPORTANT SAFEGUARDS
CAUTION! ALWAYS MAKE SURE THE POWER IS TURNED OFF
before starting installation.
BS400 INSTALLATION INSTRUCTIONS
BS400
WATTAGE 30W/45W/60W
BS400 LO/MO/HO
120-277V 50/50Hz, 347V & 480V
YES
HT (AC ONLY)/0-10V DIMMING
14 lbs
17.4” L X 17.4” W X 3.3” H
VOLTAGE
WET LOCATION
OPERATION
WEIGHT
DIMENSION
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. CAUTION! ALWAYS MAKE SURE THE POWER IS TURNED OFF before stanting installation.
2. Measure, locate fixture’s position, and mark locations for the brackets.
3. Secure brackets to ceiling as shown below. (HARDWARE BY OTHERS)
4. Wiring fixture to power supply, shall be performed by a certified electrician, and wired in a manner that
complies with all local and national electrical codes, as well as the manufacture’s wiring diagram.
SAVE THESE INSTRUCTIONS!
No user serviceable parts. Refer service to a qualif ied service
technician. Read instruc tions prior to installin g and/or operating
this device. Installatio n should be performed by a licensed
electrician/inst aller in accordance with local codes.

DIMMING WIRING DIAGRAM
BS400 INSTALLATION INSTRUCTIONS
1. 0-10V dimming wires must be run from a different conduit out of the J-box.
0-10V LEAD / DALI
VIOLET......(DIM +)
GRAY........(DIM -)
AC LEADS
BLACK...... (HOT)
WHITE........(NEUTRAL)
GREEN...... (GROUND)
HARDWARE (BY OTHERS) CEILING SURFACE TABS
BRACKET ENGAGING SLOT
TWIST TO ENGAGE
CEILING MOUNTING BRACKET
(DIRECT J-BOX MOUNT)
4” OCTAGONAL J-BOX
(BY OTHERS)
SAFETY CABLE W/ SCREW
SAFETY CABLE W/SCREW
TAB FOR
SAFETY CABLE
4.72in
[120mm]
(4x4 J-BOX)
2.75in
[69.9mm]
(3.5” OCT. J-BOX)
HINT: For ease of engaging the fixture to the mounting bracket, it
is recommended to draw temporary lines parallel to the straight
edges of the bracket (as shown above), use those line to line up
your fixture before you twist and lock the fixture onto the bracket.
2.75in
[88.9mm]
(4” OCT. J-BOX)
5.5”
J-BOX (BY OTHERS)
MOUNTING BRACKET

BS400 INSTALLATION INSTRUCTIONS
PENDANT KIT (PK)
CHAIN HANG KIT (CH)
AIRCRAFT CABLE (AC)
Install the cable glider as shown.
Attach the bracket to fixture as shown.
Install the eye-bolts into the housing as shown.
Attach stem adaptor to bracket.
Hook the chain and the eye-bolt together
using provided “S” hook.
Install stem through bracket & into adaptor.
Close all “S” hooks.
Install screw to secure the stem.
1.
1.
1.
2.
2.
3.
3.
4.
3.
2. Feed the cable through the cable glider.
(using these cable gliders for leveling the
fixture) (Push top of sleeve of cable glider
to release lock and adjust cable).
Adjust height of the fixture using this glider
(use these cable gliders for leveling the fix-
ture) (Push top of sleeve of cable glider to
release lock and adjust cable).
STEM
BRACKET
ADAPTOR
CHAIN
‘S’ HOOK
EYE-BOLT
FEED POWER
CORD THROUGH
STEM

TRUNNION MOUNT (TM)
BS400 INSTALLATION INSTRUCTIONS
Attach the bracket to fixture as shown.
Attach assembly to ceiling as shown (hardware by others).
(Canopy kit sold seperately).
1.
2.
CANOPY KIT
HARDWARE
(BY OTHERS)