Beghelli ILLUMINA BS100LED Series User manual

INSTALLATION INSTRUCTIONS
ILLUMINA® BS100LED
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600
F: 954 442 6677
www.BeghelliUSA.com
Beghelli Canada
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: [phone]
F: [phone]
www.BeghelliCanada.com
Beghelli Mexico
Av El Marques No. 70, Interior 4
76246 Mpio. El Marquez
Queretano, QRO. Mexico
P: [phone] / F: [phone]
www.BeghelliMexico.com
INDUSTRIAL
VAPOR TIGHT
926000292

ILLUMINA®
BS100LED
30W, 48W & 70W MODEL
120V to 277V or 347V INPUT
HT & SA
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not let power cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Always mount equipment in a location that is not subjected to tampering by unauthorized
personnel.
4. The use of accessory equipment not recommended by Beghelli, may cause an unsafe condition,
and will void the warranty.
5. Do not use this equipment other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
INDUSTRIAL
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LED COLOUR TEMP. / INPUT
SERIES: BS100LED
OPERATION: HT & SA
LED/COLOUR
TEMPERATURE:
WT35 (3500K)
WT40 (4000K)
WT50 (5000K)
INPUT: 120V TO 277V OR 347V INPUT
4FT LENGTH
LED STRIP
CONDUIT KNOCKOUTS
(BOTH ENDS)
REFLECTOR
LENS CLIP ( 8 TOTAL)
LENS/DIFFUSER
FIXTURE HOUSING
926000292
BS100LED

FIRST MAKE SURE POWER IS TURNED OFF!
1. Remove diffuser / lens.
2. Remove the reflector and mounting hardware bag.
3. Install conduit fitting.
4. Securely mount the fixture hardware provided. The fixture can be snapped onto the hardware as
illustrated.
5. Prepare fixture for wiring / hang reflector from internal clips.
6. Connect AC supply and ground as labeled on the provided wire leads. CAP unused wire!
CAUTION! Failure to CAP unused wire may result in a shock hazard or unsafe condition as
well as equipment failure. Route wires and secure them in place.
IMPORTANT: For the BS100LED “SA” DO NOT JOIN CONVERTER CONNECTOR UNTIL INSTALLATION
IS COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY DRIVER. SA option must specify
120V or 277V.
7. Insert LED reflector.
8. Ensure the reflector lip engages the tab channels on the housing before snapping the reflector in
position.
9. Install diffuser clips. Reposition the diffuser/lens and snap each of the eight (8) clips into place
(a “clack” sound is made).
10. Turn on AC.
SAVE THESE INSTRUCTIONS!
No user serviceable parts. Refer service to a qualified service
technician. Read instructions prior to installing and/or operating
this device. Installation should be performed by a licensed
electrician/installer in accordance with local codes.
TYPICAL INSTALLATION
926000292
BS100LED

8. SECURE DIFFUSER/LENS WITH CLIPS
1. REMOVE DIFFUSER / LENS 2. REMOVE LED REFLECTOR FROM HOUSING
3. EXTRACT MOUNTING HARDWARE,
INSTALL CONDUIT FITTING (included)
4. CONNECT TO POWER
6. INSTALL DIFFUSER CLIPS
7. INSTALL DIFFUSER/LENS
FROM
MAIN AC
L
N
G
LABELED WIRE LEADS ARE PROVIDED FOR
LINE / HOT, NEUTRAL / COMMON AND
GROUND.
LABELS WILL INDICATE THE RATED INPUT
VOLTAGE: 120V TO 277V OR 347V 60HZ.
EXACT POWER SUPPLY AND WIRING
CONFIGURATION MAY DIFFER FROM IMAGE
ABOVE: FOLLOW ACTUAL WIRE LABELS.
TYPICAL INSTALLTION
5. INSTALL LED REFLECTOR
926000292
BS100LED

DIMENSIONS
INSTALL MOUNTING HARDWARE
26.00”
50.75”
1.825” .554”
.630”
.250”
STAINLESS STEEL
MOUNTING PLATE
0.50”
3.70”
1/2” IP CONDUIT
KNOCKOUT
4.20”
WALL MOUNT
CHAIN HANG MOUNT (CH)
SURFACE MOUNT SINGLE PENDANT MOUNT (SPK)
FIXTURE REMOVAL (IF NECESARY)
MOUNTING
926000292
BS100LED

MOUNTING OPTIONS
J-BOX
CROSS BAR
CABLE GRIPPER
AIRCRAFT CABLE
WIRE TIES
POWER CORD
STAINLESS STEEL
MOUNTING PLATE
LOCK NUT
WIRE TIES
CANOPY
POWER CORD
(2) SCREWS IN J-BOX
LOCK NUT
(for double lock
on stem)
SLIP RING
(TO POSITION
CANOPY)
STEM (1/4” IPS)
STAINLESS STEEL
MOUNTING PLATE
LOCK NUT
J-BOX
CROSS BAR
CANOPY
SET SCREW
FOR SLIP RING
FEED SUSPENSION
CANOPY KIT
NON FEED SUSPENSION
CANOPY KIT
FEED SUSPENSION
CANOPY KIT
NON FEED SUSPENSION
CANOPY KIT
(screws not included)
(screws not included)
DOUBLE PENDANT MOUNTING
AIRCRAFT CABLE MOUNTING
BS100LED
926000292

DIMMING WIRING DIAGRAM
TRUNION MOUNT (TM) PIVOT MOUNT (PM)
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600
F: 954 442 6677
www.BeghelliUSA.com
Beghelli Canada
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: [phone]
F: [phone]
www.BeghelliCanada.com
Beghelli Mexico
Av El Marques No. 70, Interior 4
76246 Mpio. El Marquez
Queretano, QRO. Mexico
P: [phone] / F: [phone]
www.BeghelliMexico.com
Gray(-)
Main AC
Purple(+)
Main AC
DIMMING
0-10V WALL DIMMER.
Dims to 10%.
For dimmer switch wiring details, please refer to dimmer manufacturer’s installation guide.
(Dimmer not supplied by Beghelli)
NOTE: WIRE LOCATIONS WILL VARY. REFERENCE WIRES BY COLOUR NOT LOCATION
MOUNTING OPTIONS
JUNCTION MOUNT (JM)
BS100LED
MOUNTING CLIP
AS SUPPLIED WITH
FIXTURE
1/4-20 NUTS
MAGNET
1/4-20 SCREW
MAGNETIC MOUNT (MM)
926000292