Behringer MicroPHONO PP400 User manual

MICROPHONO PP400
Welcome to BEHRINGER
Thank you for showing your condence in us by purchasing the BEHRINGER MICROPHONO
PP400, a compact phono preamplier.
Turntables have low-level signals. However, most audio units can only process line-level
signals. Between a turntable and another audio unit (a mixer, an amplier, or a recording
unit), the PP400 acts as an intermediary, as follows:
1. The PP400 equalizes a turntable signal according to RIAA specications.
2. The PP400 amplies the RIAA equalized signal.
3. The PP400 outputs a line-level signal.
◊
◊ Please read the safety instructions that appear at the end of this document.
Connectors and Control Elements
This section illustrates and describes each PP400 connector and control element.
(2)
(1) (5)(3) (4)
Fig. 1: PP400 connectors and control elements
(1) 12 V𝌂connector:
To connect the power supply unit to the PP400, use the 12 V connector. Connecting the
power supply unit to the mains automatically switches the PP400 on. To disconnect
the unit from the mains, pull out the main cord plug.
(2) ON LED:
As soon as the unit is connected to the mains, the ON LED is illuminated.
(3) INPUT (Land R) connectors:
To send a turntable signal to the PP400, you need an RCA audio cable (stereo). Use this
cable to connect:
•
• the left output on the turntable to the L(left) INPUT on the PP400
•
• the right output on the turntable to the R(right) INPUT on the PP400
The PP400 can output a line-level signal via one of the following connectors:
•
• RCA ((4) OUTPUT L and R)
•
• ¼" TRS ((5) OUTPUT)
◊
◊ Do not simultaneously use both PP400 OUTPUTs.
(4) OUTPUT (Land R) connectors:
To use these RCA connectors, you need an RCA audio cable (stereo). Use this audio
cable to connect:
•
• the L(left) OUTPUT on the PP400 to the left input on the amplier,
recordingunit, or mixer. (On a mixer, use a CD or TAPE input.)
•
• the R(right) OUTPUT on the PP400 to the right input on the amplier,
recordingunit, or mixer
(5) OUTPUT connector:
To use this ¼", TRS (stereo) connector, you need an audio cable. Use the audio cable
to connect the PP400 OUTPUT to an input on the mixer, amplier, or recording unit.
Oneend of this audio cable must include a ¼", TRS connector. If the input on the mixer,
amplier, or recording unit is:
•
• stereo, the other end of the audio cable must include a ¼", TRS connector
•
• mono, the other end of the audio cable must include 2 TS connectors
(one for each mono input)
SERIAL NUMBER: To register your unit, use the serial number that is located on the bottom
of the PP400.
Setup Example
The following is an example of how to set up the PP400:
OUTPUT
TAPE IN/STREREO
CHANNEL IN
TURNTABLE UB1204-PRO
MICROPHONO PP400
INPUT
Fig 2: PP400 setup example

MICROPHONO PP400
Warranty
For our current warranty terms, please refer to our website at http://behringer.com.
Die deutsche Anleitung ist erhältlich @ behringer.com
Manuel francophone en téléchargement sur behringer.com
Manual en español disponible en behringer.com
Manuali italiani disponibili @ behringer.com
Русскоязычное руководство @ behringer.com
Polska instrukcja dostępna jest pod adresem @ behringer.com
Nederlandse handleiding beschikbaar @ behringer.com
Suomenkielinen käyttöohje saatavilla osoitteesta behringer.com
Svensk manual nns tillgänglig på behringer.com
Dansk vejledning ndes på @ behringer.com
Manual português disponível @ behringer.com
Ελληνικό εγχειρίδιο υπάρχει διαθέσιμο στη διεύθυνση behringer.com
@ behringer.com
@ behringer.com
Specications
Input
Type RCA connector
Impedance approx. 47 kΩ
Max. input level -23.5 dBV @ 1kHz
Output
Type RCA and ¼" TRS, stereo connectors
Impedance approx. 50 Ω
Max. output level +11.5 dBV @ 1 kHz
System Specications
Frequency response RIAA
THD 0.06% typ. @ -40 dBu/1 kHz
Gain 35 dB
Signal-to-noise ratio 68 dBu @ 0 dBu, A-weighted
Input sensitivity 5.3 mV @ 1 kHz
Power Supply
Mains connection external power supply, 12 V𝌂/ 150 mA
Mains Voltage
USA/Canada 120 V~, 60 Hz
China/Korea 220 V~, 50 Hz
U.K./Australia 240 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power consumption approx. 1.5 W
Dimensions/Weight
Dimensions (H x D x W) approx. 1 ¼ x 4 x 2 ½"
approx. 32 x 103 x 64 mm
Weight approx. 0.40 lbs / 0.180 kg
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these eorts, modications
may be made from time to time to existing products without prior notice. Specications and appearance may dier from
those listed or illustrated.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
theapparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description,
photograph, or statement contained herein. Technical specications, appearances and other information are subject to change without
notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic,
TC Helicon, Behringer, Bugera and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global
Brands Ltd. 2018 All rights reserved.
Important Safety
Instructions