Behringer PB600 User manual

behringer.com
Pedal Board with 9 V DC Power Supply and Patch Cables
Footswitches and Controllers
Ultra-compact and lightweight pedal
board for transporting up to 6 effects
pedals, including patch cables
Generous 1.7 A power adapter
included for powering more
than 12 devices*—includes
1 x 6 daisy-chain cabling
Ultra-rigid plastic design withstands
even heavy impact
High-quality components and
exceptionally rugged construction
ensure long life
Conceived and designed by
BEHRINGER Germany
When effects are an integral part of
your rig, their power adapters and
patch cables can often be the most
vulnerable part, and the most likely
to sabotage your set if they're not
pampered. Rather than tossing your
pedals, power adapters and all other
cabling into a duffel bag after a gig,
keep them safe—and ready to rock
at a moment’s notice—with
the PB600.
It's all about connections
This awesome pedal board makes
hooking up six 2.5" x 4.5" pedals as
easy as hooking up just one (of course,
if you’re using pedals that aren’t
2.5" x 4.5", the snug foam padding
can be cut to accommodate pedals of
varying shapes). The PB600 includes
¼" patch cables, so you can leave your
pedals connected to one another,
ready to pass signal even when you’re
transporting them. It also comes with
1 x 6 daisy chain cabling so that when
you plug in the 1.7 A power adapter, all
your pedals receive power. Meanwhile,
all cabling remains safe and free of
strain. Failure is almost guaranteed
when you’re dealing with a rat’s nest
of loose cabling, but with the PB600,
your effects chain is always safe and
organized.
* Depends on the power consumption
of the effects pedals, etc.
Continued on next page
PB600
Universal Effects
Pedal Board

Page 2 of 3
VD400 CS400
HB01
EQ700DR600 BO300 CS400
HB01
PH9 TO800 EQ700
ACX900
VT100FX
VT30FX
VT100FXH
412H-BK
Bugera 333XL
AM100
UM300
412H-BK
Hookup Diagram
PB600
Universal Effects
Pedal Board
Connect your guitar, bass or
keyboard to the single ¼" input in the
upper right corner of the board. A pair
of ¼" FROM EFFECTS jacks in the upper
left corner allow you to connect stereo
effects, and two ¼" OUTPUT TO AMP
jacks send a left and right stereo signal
to up to two amps.
When it’s time to load out, just
unplug the power supply, disconnect
your guitar and amp, put the lid back
on the PB600 and slide the locking
latches back into place. The heavy-
impact plastic casing will protect your
pedals from the very worst dings,
scrapes and scratches the road throws
your way.

Page 3 of 3
©2009 BEHRINGER International GmbH.Technical specifications and appearance subject to change without notice.The information contained herein is correct at the time of printing. BEHRINGER accepts no liability for any loss which
may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. All trademarks (except BEHRINGER, the BEHRINGER logo and JUST LISTEN) mentioned belong to
their respective owners and are not affiliated with BEHRINGER. FOR INTERNAL USE BY BEHRINGER DEALERS ONLY. DO NOT DISTRIBUTE. 985-10000-00382
Order via the BEHRINGER 24/7 Dealer Portal or contact the BEHRINGER location nearest you:
BEHRINGER Australia tel.: [phone], fax: [phone] BEHRINGER Germany tel.: +49
2154 9206 4149, fax: [phone] BEHRINGER Japan tel.: [phone], fax: [phone]
1181 BEHRINGER Singapore tel: [phone], fax: [phone] BEHRINGER USA / CANADA
tel: [phone], fax: [phone] behringer.com
SPECIFICATIONS
Connectors ¼" TS, unbalanced
Power supply 9 V, 1.7 A switching adaptor(included)
USA/Canada 120 V~, 60 Hz GPE182-090170-1 (HSB-UL)
Europe/Australia 230 V~, 50 Hz GPE182-090170-2 (HSB-EU)
U.K. GPE182-090170-3 (HSB-UK)
Korea 220V~, 60 Hz GPE182-090170-4 (HSB-SAA)
China 220 V~, 50 Hz GPE182-090170-5 (HSB-CCC)
Japan 100 V~, 50/60 Hz GPE182-090170-6 (HSB-JP)
Power connector 2 mm DC jack, center negative
(with daisy-chain cable included)
Power consumption 2 mA
Dimensions (H x W x D)
PB1000 504.3 mm (19 ⁄") x 663.6 mm (26 ⁄") x
115 mm (4 ½")
PB600 329 mm (13") x 663.6 mm (26 ⁄") x
115 mm (4 ½")
Weight
PB1000 approx. 5.33 kg (11.8 lbs) including PSU
& daisy chain
PB600 approx. 3.8 kg (8.4 lbs.) including PSU &
daisy chain
BEHRINGER is constantly striving to maintain the highest professional stan-
dards. As a result of these efforts, modifications may be made from time to
time to existing products without prior notice. Specifications and appearance
may differ from those listed or illustrated.
PB600
Universal Effects
Pedal Board
DC OUT connector
powers all effects
via daisy chain.
1.7 A power
adaptor connector. DC cabling duct.
Heavy-duty
plastic casing.
Sliding locks hold lid firmly in place when
pedal board is not in use.
¼" TS INPUT
connector receives
signal from
instrument.
¼" TS TO EFFECTS
connector sends
signal to effects
pedals.
Foam padding
holds effect pedals
in place.
FROM EFFECTS connectors receive stereo
signal from pedals. OUTPUT TO AMP
connectors send signal to two amps.