Behringer U-PHORIA UMC202HD User manual

Behringer U-PHORIA UMC202HD/ UMC204HD Installation for Digitizer
(Windows 7, 8 and 10)
Installing the Drivers for the UMC020xHD (Stereo users install 1 at a time)
1) Start the host PC.
2) Attach the supplied USB cable from the UMC20xHD into a free USB port on your PC
3) Windows will try and find the drivers for the UMC20xHD. Let the found new hardware wizard end
and it will say no suitable drivers found.
4) Insert the Disc marked ‘Behringer UMC Drivers and DT build’ disc and run the
‘BEHRINGER_UMC_DriverSetup_v3.29.0’file from inside the ‘Windows 7, 8 and 10’folder.
5) Follow the onscreen instructions to install the drivers. After this Windows will find the hardware
again and finish installing. Stereo users should now connect the other UMC20xHD and windows will
install the drivers automatically.
Setting the sample rate to 192khz
In order for the Digitizer to record the audio at the highest resolution, the sample rate for the UMC20xHD’s
has to be set to 192Khz. Navigate to the Windows ‘Control Panel’. Change the ‘view by’ setting in the top
left of the window from ‘Category’ to ‘Large icons’. Click on the ‘Sound’ link and this will bring up the
following window:
Select the ‘Recording’ tab at
the top. A double click on the
‘Line – BEHRINGER
UMC20xHD 192k’ will bring up
the ‘Properties’ window. Click
on the ‘Advanced’ tab and
select the sample rate of ‘2
channel, 24 bit, 192000 Hz,
(Studio quality)’. Click ‘Apply’
then ‘OK’ and close both
windows. Stereo users repeat
for the other soundcard too.
USB to Serial Cable Installation
If your Laptop/Tower PC does not have a serial (RS232) port you need to use the RS232 to USB adaptor
(supplied). To install...
1) Start the host computer system and insert the CD marked 'USB to serial driver' into the CD/DVD
drive on your PC.
2) Browse to the CDROM folder D:\USB Serial Adapter\Windows\
3) Select the appropriate folder for your operating system and Double click on the icon
PL2303_Prolific_DriverInstaller
4) Follow the on-screen instructions to install the driver. Plug in the USB to serial adaptor, Windows
will apply the drivers automatically.
5) Check in the Windows device manager, under ports (COM & LPT) you should see Prolific USB to
serial COM port(COM??) The COM port that is emulated by the USB to serial adaptor is displayed in
the brackets.

Connecting the Digitizer to the PC and UMC20xHD
Using the supplied multi cable,
1) Connect the 15 pin D-type connector to the back of the Digitizer.
2) Connect the smaller 9 pin D-type connector to the serial port of the PC or the USB to serial adaptor.
3) Connect the ‘A’ side jack plug to ‘Input 1’ and the ’B’ side jack plug to ‘Input 2’ of the UMC20xHD.
Stereo users connect the ‘AL’ jack plug to ‘Input 1’ and ‘AR’ jack plug to ‘Input 2’ of one of the
UMC20xHD’s. Leave the ‘B’ side jacks unplugged at this moment.
The gain controls on the front of the UMC20xHD can be used to
give a little extra level if required but ensure the level meters in
the Graff software do not hit the top otherwise distortion will
be introduced.
First run with the Digitizer
After installing the Graff Digitizer software from the ‘Digitizer 6.18’ CD, you can run the program from the
shortcut icon created on the desktop. When the software runs for the first time it needs to find the
Digitizer com port and assign the soundcards. This is done by clicking on the ‘About’ link at the top of the
window.
From here you can select the com port that
the Digitizer is using. Select each one in
turn until you see the information about
the Digitizer displayed in the box below the
com port selector. The soundcards will be
automatically assigned on exit from this
page. Mono users are now set up and ready
to go.
For a stereo system, the software assigns
one soundcard per side but we need to
establish which soundcard is being used for
which side:
For the stereo Digitizer, Digitize a tape and see if the A side level meters show. If they show then plug
the B side jacks into the other UMC20xHD. If the B side meters show, then swap the A side jacks into the
other UMC20xHD and put the B side jacks into the first UMC20xHD.