Belcat CADIC-2 User manual

DCBA GFE #
Chromatic Tuner
BASS
MIDDLE
TREBLE
MASTER
TUNER
Low
Batt.
: Tuning Guide LED for Sharp tune
: Tuning Guide LED for right tune
: Tuning Guide LED for flat tune
3Band Pardmetric EQ with Chromatic LED tuner
1
2
3
4
5
6
7
8
9
10
11
1. Tuner LED Display
2. Bass
3. Middle
4. Treble
5. Volume Knob
6. Low Batt. (Low Battery LED Light)
7. Tuner on/off Button
8. Piezo Knob
9. C-MIC Knob
10. Tone Knob
11. Phase Button
Tuner LED Display
The BASS, MIDDLE, TREBLE controls are a 3-band equalizer for
controlling tone.
The center detent on these tone controls yields a flat tone response.
“+12" boosts the tone; “12"cuts the tone.
The LED will light when the battery has lost power. Replace the
battery when this light is on.
This LED light will flash when a cable is connected to the output
jack of the pickup system. This shows the battery is good.
The PHASE button controls the phase of the pickup in relationship to
the phase of the speaker that are being used with the system.
Pushing this button will put the pickup “out of phase” with the
speaker. When the button is out the pickup is “in phase.”
This control is most useful for feedback control and will provide a
tone color. Once you experiment with the settings of this control you
will find more about how it works.
The VOLUME controls the output volume. At “0" it is completely OFF.
At “10" it is loud.
Caution
- The jack should be pluged for proper Preamp working.
(TUNER will works regardless pluging jack)
- There is no output sound, please check if tuner or mute is turned on.
- When LCD screen is dim or no display, please check battery life.
- To prevent battery loss, please unplug jack when preamp is not in use.
- Do not disassemble for repair.
Return to your dealer for service or repair.
- Do not use too much force when operating the control.
Specification
3 4
12
1. Tuner LED Display
2. Bass (for bass tones)
3. Middle (for middle tones)
4. Treble (for high tones)
5. Volume Knob
6. Low Batt. (Low Battery LED Light)
7. Tuner on/off Button
8. Piezo Knob
9. C-MIC Knob
10. Tone Knob
11. Phase Button
Functions
PREAMP USER’S MANUAL
CADIC-2
Features : 3Band EQ, Piezo & C-Mic Blender
with Chromatic LED tuner
Frequency Response : 20Hz ~ 20KHz
Control Range
Bass : +/-12dB at 80Hz
Middle : +/-12dB at 1KHz
Treble : +/-12dB at 10KHz
Volume control for Master
Volume control for Piezo pick-up
Volume control for C-Mic
Tone control for C-Mic
Phase Switch
Battery Status LED
Power Supply : 9V Alkaline Battery
Battery Life
Only EQ: Over 700Hours
Tuner on : Over 300Hours
Pick-up : Omega II Piezo Cable pick-up
Dimensions : W 78mm X H 55mm (3.1" X 2.2")

INSTALLATION MANUAL
1. Electric Drill
2. Drill Bit
(2.3mm or 3mm)
3. Phillips Screwdriver
4. Router and Grinder
(cutting-edge 3mm)
5. Round File
6. Masking Tape
Masking
Tape
Masking
Tape
1. Preamp
2. Battery
Box
3. Pick-Up
4. Clip
8. Fix wire with clip.
5. Screw
1. Contents
2. Tool 2.Drilling hole for pick-up
3. Insert EQ and battery box into hole of guitar.
1. Cut out the hole with template
4. Fasten screws properly.
5. Put plugs
into jacks.
6.Installing the pick-up
Cutting
Template
Cutting
Template
1) When there is no sound or sound is stopped,
- Check guitar cable, amp or Mixer
- Check if there is batter or not. When it happens noise or distortion,
please exchange battery.
- Check if the pickup and battery connector is connected correctly
or not.
- Check if out put jack is connected correctly.
2) When there is hum-noise,
- Check the pickup is connected well or not.
- Check if the connectors are connected to correct position well
or not.
3) Some causes of the balance problem
- When the bottom of saddle or the groove of saddle is not flat.
- When saddle is installed to the groove of saddle loosly.
- When the connection is not good between the bottom of saddle
and the groove of saddle.
- When Saddle is very short
- When there is grounds on the groove of saddle.
- When Saddle is declined toward front or back.
- When the top of guitar is bended.
- When the pickup is installed to only a part of the groove of saddle.
Solution
Pick-up
Wire
Clip
EQ Battery box
Cable
Battery
Box
Pick-up
wire
(back page)
Preamp Battery Box
DCBA GFE #
Chromat ic Tu ner
BAS S
MID DL E
TRE BL E
BRI GH T
MID DLE FREQ .
NOT CH
VOL UM E
TUN ER
Low
Bat t.
PHA SE

Cutting Template
1.Print this file without scaling option.
2.Check the size with actual ruler.
3. Cut out the dotted line or desire model.
4. Adhere to location use double stick tape.
5. Cut follow solid line use cutter.
Print>Page Handling>Page Scaling
None
Fit to print margins
Reduce to print margins
Multiple pages per sheet
1 2 3 45678 9 10 11 12 13 14 15
Preamp Opening Battery Box Opening
Ø2.0mm
DCBA GFE #
Chromatic Tuner
BASS
MIDDLE
TREBLE
BRIGHT
MIDDLE FREQ.
NOTCH
VOLUME
TUNER
Low
Batt.
PHASE
47.0mm
69.0mm
52.2mm
26.1mm
Ø2.0mm