Belcat UK-300T User manual

: Tuning Guide LED for Sharp tune
: Tuning Guide LED for right tune
: Tuning Guide LED for flat tune
2Band EQ with Chromatic LED tuner
1. Tuner LED Display
2. Bass
3. Treble
4. Volume Knob
5. Low Batt. (Low Battery LED Light)
6. Tuner on/off Button
7. Battery box
Tuner LED Display
The BASS, TREBLE controls are a 3-band equalizer for controlling
tone.
The center detent on these tone controls yields a flat tone response.
“+12" boosts the tone; “12"cuts the tone.
The LED will light when the battery has lost power. Replace the
battery when this light is on.
This LED light will flash when a cable is connected to the output
jack of the pickup system. This shows the battery is good.
The VOLUME controls the output volume. At “0" it is completely OFF.
At “10" it is loud.
Caution
- The jack should be pluged for proper Preamp working.
(TUNER will works regardless pluging jack)
- There is no output sound, please check if tuner or mute is turned on.
- When LCD screen is dim or no display, please check battery life.
- To prevent battery loss, please unplug jack when preamp is not in use.
- Do not disassemble for repair.
Return to your dealer for service or repair.
- Do not use too much force when operating the control.
Specification
3 4
12
1. Tuner LED Display
2. Bass (for bass tones)
3. Treble (for high tones)
4. Volume Knob
5. Low Batt. (Low Battery LED Light)
6. Tuner on/off Button
7. Battery box
Functions
UK-300T USER’S MANUAL
Features : 2Band EQ with Chromatic LED tuner
Input Impedance : 22 MΩ
Frequency Response : 20Hz ~ 20KHz
Control Range
Bass : +/-12dB at 100Hz
Treble : +/-12dB at 10KHz
Battery Status LED
Power Supply : 2 X CR2032 Coin Battery
Battery Life
Only Eq : Over 200Hours
Tuner on : Over 100Hours
Pick-up : Omega II Piezo Cable pick-up
Dimension : W 56mm X H 40mm (2.2" X 1.6")
1
2
3
4
5
6
7
Power switch of built-in Chromatic LED tuner.
Automatic power off after 5 minutes
2 X CR2032 Coin Battery

INSTALLATION MANUAL
1. Electric Drill
2. Drill Bit
(2.3mm or 3mm and 12mm )
3. Phillips Screwdriver
4. Router and Grinder
(cutting-edge 3mm)
5. Round File
6. Masking Tape
Masking
apeT
1. Preamp
3. Pick-Up
4. Clip
7. Fix wire with clip.
5. Screw
1. Contents
2. Tool 2.Drilling hole for pick-up
1. Cut out the hole with template
Cutting
Template
1) When there is no sound or sound is stopped,
- Check guitar cable, amp or Mixer
- Check if there is batter or not. When it happens noise or distortion,
please exchange battery.
- Check if the pickup and battery connector is connected correctly
or not.
- Check if out put jack is connected correctly.
2) When there is hum-noise,
- Check the pickup is connected well or not.
- Check if the connectors are connected to correct position well
or not.
3) Some causes of the balance problem
- When the bottom of saddle or the groove of saddle is not flat.
- When saddle is installed to the groove of saddle loosly.
- When the connection is not good between the bottom of saddle
and the groove of saddle.
- When Saddle is very short
- When there is grounds on the groove of saddle.
- When Saddle is declined toward front or back.
- When the top of guitar is bended.
- When the pickup is installed to only a part of the groove of saddle.
Solution
Pick-up
Wire
Clip
EQ Out put jack
Cable
Out put
Jack
(back page)
Preamp
Masking
apeT
12mm
3. Insert EQ and battery box into hole of guitar.
4. Fasten screws properly.
5. Put plugs
into jacks.
6.Installing the pick-up
Pick-up
wire
Out put Jack
2. Output Jack

Cutting Template
1.Print this file without scaling option.
2.Check the size with actual ruler.
3. Cut out the dotted line or desire model.
4. Adhere to location use double stick tape.
5. Cut follow solid line use cutter.
Print>Page Handling>Page Scaling
None
Fit to print margins
Reduce to print margins
1 2 3 45678 9 10 11 12 13 14 15
Preamp Opening
50.9mm
34.6mm Ø2.0mm