Beliani KELUD User manual

FIREPIT
Warnings: You must read this before you proceed.
Page 1 OF  Page 1 OF

Page 2 OF 

Unpack all
the parts
for a clear
overview.
Before Beginning Assembly:
Page 3 OF 
Step 1
Unpack all components carefully from the package. Put the
Fire Pit Body on a hard, level and non-combustible
surface.

Step 2
Step 3
Insert Bowl Handles into the holes on the inside Fire Bowl
wall, as depicted in the picture.
Page 4 OF
Step
3
Put the Fire Bowl into the Fire Pit opening as shown in
Step 3 above. Make sure it sits evenly in the frame
housing.
Page 4 OF 

Step 4
Step 5
Take out the Handles after the Fire Bowl is placed inside
the Fire Pit Main Housing. Place the Log Grill into the Fire
Bowl.
Put the Spark Safeguard Screen onto the top opening of
the Fire Pit Body and make sure it sits into it evenly. The
Firepit is ready for use.
Page 5 OF


Operating Instructions:
WARNING
FOR YOUR SAFETY
Before using this outdoor fire pit, make sure you
have read, understood and are following all
information provided on page 1 of this manual.
Failure to follow those instructions can cause
death, serious injury or property damage.
Lighting:
1. Make sure there is only a small amount of
ash (1/2” thick) at the bottom of the metal
bowl.
2. Place a layer of dry kindling or a natural fire
starter onto the center of the log rack.
3. Place above that layer the dry seasoned
hardwood that is cut to lengths no more than
12”
4. Use a match to light kindling or fire starter.
5. Replace the safeguard spark screen when
the kindling or fire starter is lit.
Tending the Fire
You may need to shift and/or add logs for an
ideal experience.
Reminders:
●Always wear protective gloves or a pot
holder when tending a fire.
●Wait until glowing wood have developed
before adding any additional wood.
●Do NOT add gasoline, kerosene, diesel fuel,
lighter fluid or alcohol to relight or enhance
an existing fire.
1. Use a long handled fire pit tool to carefully
take away the spark screen.
2. Use the long handled fire pit tool to shift the
logs to allow additional airflow.
3. If additional wood is required, place wood on
top of the burning log. Be careful not to shift
ashes.
4. Replace the safeguard spark screen.
Extinguishing
1. Allow fire to burn itself out.
2. Do NOT use water to extinguish as this is
dangerous and can cause damage to this
outdoor fire pit.
Maintenance Instructions:
Inspecting
This outdoor fire pit should be inspected on a
regular basis to ensure product safety and longer
product life.
Check all parts to make sure they are secure.
Cleaning
This outdoor fire pit should be cleaned on a
regular basis to promote safer experiences and
longer product life.
Note: After repeated use, a slight discoloration of
the finish may occur.
Reminders:
Do NOT attempt to clean this outdoor fire pit
until the fire is COMPLETELY out.
Do NOT use oven cleaner or abrasive
cleaners as they will damage this product.
Do NOT clean any part of this outdoor fire
pit in a self-cleaning oven as it may damage
the finish.
1. Wipe exterior surfaces of the metal parts with
a mild dishwashing detergent or baking soda.
2. For stubborn surfaces on the metal parts,
use a citrus based degreaser and a nylon
scrubbing brush.
3. Rinse clean on the metal with water.
4. Use a soft dry brush to wipe away the dust
on the faux stone fire pit body. Never use
water or other liquids to clean the faux stone
top.
Storage
Do NOT move or store this outdoor fire pit until
the fire is COMPLETELY out.
1. Once the fire is out, logs are cold and
outdoor fire pit is cool to the touch, remove
ashes and properly dispose.
2. Store assembled in a location away from
children and pets.
Note: If you do not use a cover, store this
outdoor fire pit in a dry location free from
rain.
Page OF

Powered by TCPDF (www.tcpdf.org)