Belling CRS60 Instruction Manual

Belling
CRS60 Hob
0
Users Guide & Installation
Handbook

GENERAL
Carefully read the contents of this leaflet
since it provides important instructions
regarding safety of installation, use and
maintenance.
Keep the leaflet for possible future consul-
tation. All the operations relating to instal-
lation (electrical connections) must be car-
ried out by specialised personnel in con-
formity with the regulations in force.
SAFETY WARNINGS
It is recommended to use flat-bottom pans
with a diameter equal to or slightly larger
than that of the heated area. Do not use
pans with a rough base to prevent scratch-
ing the heat surface of the cook top
(Fig.3).
This appliance is not suitable for use by
children or persons requiring supervision.
Do not let children play with the appliance.
IMPORTANT
lAvoid spilling liquid, therefore to boil or
heat liquids, reduce the heat.
lDo not leave the heating elements on
with empty pots and pans or without
receptacles.
lWhen you have finished cooking, switch
off the relevant heating element with the
control indicated below.
ATTENTION: Steam cleaners must not be
used.
WARNING: If the surface is cracked,
switch off the appliance to prevent electric
shock.
INSTALLATION INSTRUCTIONS
These instructions address specialised
installers and serve as a guide for installa-
tion, adjustment and maintenance in con-
formity with the laws and regulations in
force.
POSITIONING (Fig.1)
The domestic appliance is designed to be
built into a work top as illustrated in the
specific figure.
Apply sealant around the entire perimeter
(cut-out dimensions Fig.1B).
Fix the domestic appliance on the work top
by means of the 2 brackets provided, tak-
ing the thickness of the work top into
account (Fig.1A).
If the lower part of the appliance, after
installation, is accessible via the lower part
of the cabinet then it is necessary to
mount a separator panel respecting the
distances indicated (Fig.1C).
If the appliance is installed with an oven
underneath then the separator is not nec-
essary.
Instructions
40mm
30mm
Incorrect:
Concave base Incorrect:
Convex base
Correct:
Flat base
25mm
48mm
580mm
48mm
53.5mm
495mm
510mm
50mm
min
50mm
min
560mm
fig 3
fig 1B
fig 1A
fig 1C
1

ELECTRICAL CONNECTIONS
Before making the electrical connections,
check that:
lthe ground cable is 2 cm longer than the
other cables;
lthe system ratings meet the ratings indi-
cated on the identification plate fixed on
the lower part of the work top;
lthe system is fitted with efficient earth-
ing compliant to the laws and regulations
in force.
Earthing is obligatory by law.
Live should be wired to terminal ‘L’.
Neutral should be wired to terminal ‘N’.
Earth should be wired to terminal ‘E’ or
If the domestic appliance is not fitted with
a cable and/or relevant plug, use material
suited to the absorption value indicated on
the identification plate and the operating
temperature.
At no point must the cable reach a tem-
perature 50°C higher than room tempera-
ture.
If wishing to make a direct connection to
the mains, an omnipolar switch must be
interposed with a minimum opening of 3
mm between the contacts and suited to
the load indicated on the plate and con-
form to the regulations in force (the yel-
low/green ground conductor must not be
interrupted by the switch). When the
appliance has been installed, the omnipo-
lar switch must be easily accessible.
USE AND MAINTENANCEMAINTENANCE
Remove any residues of food and drops of
grease from the cooking surface using the
special scraper supplied on request (Fig.5)
Clean the heated area as thoroughly as
possible using SIDOL, STAHLFIX or similar
products and a cloth/paper, then rinse with
water and dry with a clean cloth. Using
the special scraper (optional) immediately
remove any fragments of aluminium and
plastic material that have unintentionally
melted on the heated cooking area
or residues of sugar or food with a high
sugar content (Fig.5).
In this way, any damage to the cook top
surface is prevented.
Under no circumstances use abrasive
sponges or irritating chemical detergents
such as oven sprays or stain remover.
USE
Use the control knobs to set the desired
power. Turn them clockwise to maximum.
In the case of plates with a double area,
the external heating element can be
switched on starting from zero and
turning in an anticlockwise direction.
The hit hob lights are ON when:
lthe top temperature at the Indicated
spot is higher than 50°C.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR EVENTUAL
DAMAGES CAUSED BY BREACHING
THE ABOVE WARNINGS.
Instructions
fig 5
2

0826392 01© 11.2010
Glen Dimplex Home Appliances, Stoney Lane, Prescot, Merseyside, L35 2XW
Belling Customer Care
0844 815 3746