Belson Outdoors SANISTAND User manual

111 North River Road
North Aurora, IL 60542
Phone: [phone]
Fax: [phone]
[email protected]
Model # SAN1-2100 Instructions Sheet
www.belson.com
SANISTAND™ HAND SANITIZER STAND | ADA COMPLIANT
We recommend reading through the entire assembly
instructions prior to proceeding with installation, service
and maintenance. All references to left and right
throughout this guide are as viewed from the front.
DIMENSION
Height
Width
Depth
Number of Single Dispenses
Weight Empty w/Dispensers
Base Capacity
IMPERIAL
66
in
28 in
28 in
5333
36 lbs
23 gal
METRIC
168 cm
71 cm
71 cm
5333
16.3 kg
87.1 L
SPECIFICATIONS
~~Assembly Tools Required~~
•Drill with a Phillips Bit
or a Phillips Head Screwdriver
Full Scale Fastener Drawing
(4) PC-000158
Self-Tapping Screws

www.belson.com
SAN1-0001G - Base
PC-000554 - 1” Plug
Gray w/Tether
(1) PC-000345 - O-Ring
PC-000762 -
Locking Rod
PC-000205M - Lock
SAN1-0005 -
Dispensing Pipe
(4) FD1-1000 -
Hand Foam Dispenser
(16) PC-000105 - Rivet
(16) PC-000106 - Washer
(1) SAN1-0004*TC -
Top Foam Dispenser Holder
(1) SAN1-0004*BC -
Bottom Foam Dispenser Holder
(4) PC-000158 -
Self-Tapping Screws
* = Specify Color Option

www.belson.com
General Use and Information
Assembly Instructions
NOTE: All drilling will require a 13/64” bit. * = Specify Color Option
Step 1. Insert the SAN1-0005 - Dispensing Pipe into the SAN1-0001G - Base.
Step 2. Line up the pre-drilled holes of the base and dispensing pipe. Insert
a PC-000762 - Locking Rod through the holes of the base and dispensing pipe
and push through to the other side. Place a PC-000205M - Lock onto the lock-
ing rod and secure in place.
NOTE: The suggested positioning of the Dispenser Holders would be with the
Foam Dispensers in opposition of each other (the top two dispensers opposite
the bottom two dispensers).
Step 3. Place the SAN1-0004*BC - Bottom Foam Dispenser Holder (the holder
with a hole through the center) onto the dispensing pipe, lining up the corners
of the holder with the corners of the base.
Step 4. Place the SAN1-0004*TC - Top Foam Dispenser Holder onto the dis-
pensing pipe, (the holder with a center hole at the bottom) lining up the corners
of the holder with the corners of the base
pipe).
Step 5. While pushing down on the top of the holder, drive (2) PC-000158 Self-
Tapping Screws through the two drill spots located along the top of the holder
and through the dispensing pipe.
Step 6. ts up against the bottom of the
top holder (with the foam dispensers opposite as suggested). Drive (2) PC-000158
Self-Tapping Screws through the two drill spots located along the top of the
holder and through the dispensing pipe.
Filling a Dispenser:
ll a dispenser, push up on the tab from underneath the dispenser and pull
down the cover. Fill with Rid-It™ - Foam Hand Sanitizer (follow the instructions
located on the sticker inside of the foam dispenser). Order Part #FD1-0001 for a
lls, available from PolyJohn.
Filling the Base:
ll the base with water or sand (in order to create enough ballast to keep from
being tipped over), unlock the lock from the base and remove the lock, locking
rod and dispensing pipe. Fill with either water or sand and reinsert the dis-
pensing pipe, locking rod and lock.
NOTE: lling with sand, make sure to tilt the base on its side to keep the bottom
raised area free from sand for proper re-installation of the dispensing pipe into the base.
Draining the Base:
lled with water, simply loosen the PC-000554 Plug located
nished draining. If
lled with sand, unlock the lock, remove the lock and locking rod and pull out
the dispensing pipe. Turn the base upside down and empty. Reinsert the dis-
pensing pipe, locking rod and lock when empty.