HOME8 ADS1301 User manual

1/4
User manual
Activity tracking sensor
Model No: ADS1301
FCC ID: 2AE59ADS1301

2/4
1 system introduction
Activity sensors log users daily routine. e.g. Attach a sensor to the refrigerator and other
kitchen objects to infer when food is prepared or consumed. OPU receives activity
signals from each of the sensors to log more detail.
2 Specification
Sensor Requirement
Device Type
Activity tracking sensor
Alarm Sensor Type
Movement (front, back, left, right, up and down)
Detection type
A signal will be issued when the sensor detects a
movement of the object it attached to.
Communication Requirement
RF Frequency
433.92MHz
Modulation
ASK
Antenna
Internal Antenna, VSWR<2, Peak Gain di
System Requirement
Power
3 volt battery CR2032
Power Consumption
6 month (Triggered 10 times a day)
Standby current
≤40uA
Trigger current
≤30mA
Battery’s voltage status
3V (Full power – functional)
2.1~2.35V (Low battery warning)
Below 2.1V (shuts down)
Operating Environment
Working Temp: -10
ɗ
~50
ɗ
Humidity:
5%~80%RH non-condensing
Storage Temp:
-20ɗ~60ɗ
Humidity: 5%~85%RH
Environmental Standard
RoHS, REACH
Alarm Type
Heart Beat
Alive signal will be issued once per 12 hours.
Activity Signal
Each movement of the object being monitored will issue an
RF signal for this event
.
(Variance
烉
1600 for Refrigerator)
Low Battery Alarm
The device will send out a low battery signal, if the voltage
drop to low battery state and the signal will be sent
accompany heart beat and other alarms.
LED Indicator
* LED color: Red
* Normal Operation: LED off

3/4
* Power on: Flash Frequency 250 ms on/off
炻
4 times
* HeartBeat&Event Alarm
烉LED on 460ms炻then off
* Low Battery (When the battery is lower than 2.4V): Flash
Frequency 50 ms on/off, 5 times
Silence Time
When Activity sensor power on within 5 minutes, once
Activity sensor alarms it will start to count 5 seconds, if any
movement detected in this silence period, the alarm will be
not triggered. After the 5 minutes, the silence period is 1
minute.
Activity trigger alarm
Once Activity sensor alarms it will start to count 1 minute, if
any m
ovement detected in this period
.The alarm will be not
triggered.
3 Operating instructions
1. First use the Activity sensor, pull up the insulation spacer.
2. The Activity sensor fixed right where you need to detect, such as
the refrigerator door, need to pay attention to the fixed in the near
the door, away from the door of the shaft, because it is not easy to
detect.
3. When battery low power, if Activity sensor send alarm, the low
battery alarm will accompany to sending.
4. If battery low power, please replace the battery as soon as possible.

4/4
FCC Statement
This device compiles with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
a) This device may not cause harmful interference
b) This device must accept any interference received, including
interference that may cause undesired operation.
Warming! This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept
any interference received, including interference that may cause undesired operation.
N
ote: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
p
rotection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.